DATA LOGGER Model DL-SA11 User’s Manual Felix Storch, Inc. An ISO 9001:2008 registered company 770 Garrison Avenue Bronx, New York 10474 www.summitappliance.
Product Overview This data logger is used mainly to record the temperature of food, pharmaceuticals, chemicals, etc., during storage and transportation. It is especially applicable to container transportation of temperature-sensitive goods by sea, air and road for large export-oriented enterprises and global chain enterprises. Specifications………………………………………………………………………. Size (length x diameter): 131 x 24 mm (5.16‖ x 0.95‖) Technical parameters: Temperature measuring range: -30°C to 70°C Resolution: 0.
Configure parameters Refer to the data management software instructions for details (pages 8 –14) Caution! Make sure you have saved selected parameters. Default Settings Alarm Settings Logging interval Stop mode: Start Mode: Temp. Unit Buffer Ring: H1 (high alarm) = L1 (low alarm) = Alarm Mode: Other settings 5 minutes Software Instant on o C Disabled 10 oC 2 oC Single 0-11 hours; 0-59 minutes; 0-50 seconds Manual stop (see pp. 3-4 ) Manual and timing start (pg.
and the data logger is not stopped manually, the data logger will save the data by overwriting the initial data. (It keeps the statistical information of the whole transportation process.) NOTE: When the record capacity exceeds the Max capacity (32,000 points) in the manual mode, the data logger can continue recording the temperature state of the whole transportation process but only keep the details of the last 32,000 points.
Menu 4: Current record interval. (e.g., the digit N following the decimal point represents N*10 sec. Fig.6 shows the record interval is set to 12 min 50 sec.) Fig.6 Record interval Menu 5: MKT value. Menu 6: Average temperature value. Fig.7 Static Fig.8 indicates it stopped recording Menu 7: Max temperature value. Menu 8: Min temperature value. Fig.9 Fig.10 Menu 9, 10, 11: Set upper limit of temperature. See Fig.11, 12, 13 Fig.11 Upper limit 3 Fig.12 Upper limit 2 Fig.
Content of exported report The report varies based on the set alarm types. When unit is set to ―no alarm‖, there is no alarm info on the top right corner of the first page or color mark among data. When it is set to ―alarm‖, relative alarm info appears in the alarm info column based on the selected alarms. Over high temperature data is in red. Below low temperature data is in blue. Normal data is in black.
Step 2. Press the snap to remove the compartment. See Fig. 21. Fig.21 Step 3. Remove the battery compartment. See Fig. 22. Fig.22 Step 4. Remove the old battery and Install the new one. See Fig. 23. Fig.23 Step 5. Adjust the button and the internal light pipe to the same side; snap the compartment shut. See Fig. 24. Fig.24 Step 6. To re-install the transparent cap, rotate it in the direction shown in Fig. 25. Fig.
Data Management Software Instructions Data Management Software can upload all recorded data to a computer and systematically analyze, collect and manage data. 1. Installation environment Hardware environment： CPU：above PII600MHZ Hard disk：above 40G Memory：above 512M Operation system: Windows XP（32bit、64bit, Windows Vista（32bit、 64bit, Win7（32bit、64bit） ，Windows8(x86/x64) 2. Main functions 2.
Parameter information： Serial Number——Data logger ID Stop Time——Stop time Log Interval——Record interval Data points——Total record points Time Base——Time Zone Elapsed time——Total record time Start Mode——Logger start mode MKT——Mean kinetic temperature Start Delay——Logger start delay time Over——Alarm upper limit Buffer Ring——Buffer Ring Below——Alarm lower limit Trip ID——Trip ID number Allow Time——Alarm delay time Description—Trip description Total time——Accumulated alarm time Highest ——Max.
Data table ——Displays first page data ——Displays previous page data ——Displays next page data ——Displays last page data ——Skips to a specific page R3-081016 10
3.
4. Data management page ——Data backup (saves data in the format of ELT) ——Data restore (restores ELT file and reads it by software) ——Back to home page 5.
Parameter information： Serial Number——Data logger ID Start Mode——Logger start mode Trip ID——Travel ID number Travel DSC——Travel description Log Interval——Record interval Report Language——Report Language Time Base——Time Base Battery——Battery display Cycle—— Total record time available No Alarm ——Alarm threshold not set Password——Setting password Stop Mode——Logger stop modes Multiple Alarm——Set several alarm thresholds Multiple Work——Permit logger to be started or stopped several times Probe Type—
7. Export data page Export data in the EXCEL format Export data in the AI format Export data in the ELT format Restore/insert ELT data to the software Customer Support …………………………………………………………….……… For technical support, please call 800-932-4267 (U.S. and Canada) or email info@summitappliance.com; for calibration services please contact calibration@summitappliance.com . Limited Warranty…………………………………………………………….
