OUTDOOR KEGERATOR Model SBC696OSNK User Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Installation Instructions 5-9 Before Using your Appliance 5 Locating your Appliance 5 Guardrail Installation 5 Caster Installation 6 Door Handle Installation 6 Reversing the Door Swing of your Appliance 6-9 Operating your Appliance 10-11 Control Panel 10 Setting the Temperature 10 Defrosting 11 Interior Light 11 Interior Fan 11 Alarms 11 Black Plastic Tube 11 Care and Maintenance 12 Cleaning your Appliance 12
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words "DANGER" or "WARNING".
• • • • • • • • • • • • • • • • • • • For every ounce of coolant at least 325 cubic feet of room space is required. The amount of coolant in the appliance is stated on the data plate on the back of the appliance. It is hazardous for anyone other than an Authorized Service Person to carry out servicing or repairs to this appliance. Take serious care when handling, moving, and using the appliance to avoid either damaging the refrigerant tubing or increasing the risk of a leak.
INSTALLATION INSTRUCTIONS Before Using your Appliance • • • • • • • • Remove the exterior and interior packaging, but do not remove any foam insulation surrounding the pipes at the back. Before connecting the unit to the power source, let it stand upright for approximately 24 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth.
Caster Installation 1. 2. 3. 4. 5. Remove everything from the cabinet and lay the unit on a clean, dry, and padded sur face Install casters into the holes on the bottom of the unit as show n and tighten with a wrench The two casters equipped with locks should be installed on the front of the unit Once all four casters are attached, return the beer dispenser to an upright position Allow the unit to sit for 8-10 hours before plugging in to allow the refrigerant to settle.
Step 1 A. Take out two hex keys from a bag in the cabinet. Insert the small hex key (1) to the axes (2). B. Rotating the axes (2) clockwise. C. Use the big hex key (3) to push the pin (4) until you can remove the pin by hand. Step 2 A. Remove the top right screws (5) from the right top hinge (6). Gently pull down the door and place it on a padded surface to avoid the risk of damage. B. Transfer the top left screws (7) to cover the top right holes. Step 3 A.
Step 4 A. Remove the screws (5) from the hinge plate (13). B. Place the hinge plate (13) on the bottom left. C. Fix the screws (5) on the hinge plate (13) again. Step 5 A. Place the axes (2) on the left hinge plate. Step 5 A. Screw the alternative left top hinge (12) included with the unit, onto the left-hand side of the cabinet, and tighten it after the door is leveled.
Step 6 A. Place the axes (2) on the left hinge plate. Step 7 A. Loosen the small screw a little (around 0.3”), making sure the pin is not higher than the screw. B. Use the small hex key (1) to rotate the axes (2) counter-clockwise. C. Insert the pin (4) when you find your desired self-closing strength.
OPERATING YOUR APPLIANCE The Kegerator is ab le to maintain the proper dispensing temperature for beer, provided it is installed correctly in the proper environment. For best results, mount the draft tower as close to the top of the kegerator as possible and seal any openings to prevent heat transfer. Avoid opening and closing the door of the kegerator too often to ensure a consistent temperature inside the unit. Factory preset temperature is 34 degrees Fahrenheit.
Defrosting The Kegerator defrosts automatically under normal operating conditions. Condensate collects in the drainage channel behind the rear wall of the unit, and flows through a drainage hole into the drip tray near the compressor, where it evaporated. Frost may accumulate on the evaporator if the unit is repeatedly opened in high heat or high humidity locations. If this frost pattern does not clear within 24 hours, the appliance will require manual defrosting.
CARE AND MAINTENANCE Cleaning your Appliance • • • • • • Turn off the power, unplug the appliance, and remove all items including the dispense kit. Wash the inside surfaces with warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts. Wash the outside cabinet with warm water and mild liquid detergent.
TROUBLESHOOTING There are many common issues you may experience with your kegerator that can be solved very easily, without the need of a service call.
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factoryspecified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
