BEVERAGE MERCHANDISERS Model Nos.: SCR610BL / SCR1156 Instruction Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Write Serial No. (on lower left corner of inside cabinet) here: ____________________________________________ Felix Storch, Inc. 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Appliance Safety 3 Important Safeguards 3-4 Location of Parts 5 Installation Instructions 6-8 Before Using Your Appliance 6 Installation of Your Appliance 6 Electrical Connection 6-7 Extension Cord 7 Reversing the Door Swing of Your Appliance Installing the Stainless Steel Handle 7-8 8 Operating Your Appliance 8-10 Control Panel 8-9 Setting the Temperature Control 9 Dynamic Cooling Mode 9 Sabbath Mode 9-10 Temperature Memory Function 10 Temperature Alarm / Doo
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words "DANGER" or "WARNING".
In the event of any damage: - Avoid open flames and anything that creates a spark, - Disconnect from the electrical power line, - Air the room in which the appliance is located for several minutes and - Contact the Service Department for advice. The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a leakage, if the appliance is in a small room, there is the danger of combustible gases building up.
LOCATION OF PARTS MODEL SCR610BL Door Shelves (3) Handle Security Lock Ventilation Grille Adjustable Legs Digital control panel Cabinet MODEL SCR1156 Door Shelves (4) Handle Security Lock Ventilation Grille Adjustable Legs Digital control panel Cabinet 5
INSTALLATION INSTRUCTIONS BEFORE USING YOUR APPLIANCE Remove the exterior and interior packing. CAUTION: After unpacking you MUST allow your appliance to stand upright for at least 2 hours to allow the lubricant and refrigerant to drain back into the compressor and stabilize. Failure to do so may adversely affect performance and the lifetime of the unit. Clean the interior surface with lukewarm water using a soft cloth. Install the handle on the door. (See page 8.
To prevent accidental injury, the cord should be secured behind the appliance and not left exposed or dangling. The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevents overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the appliance by pulling on the power cord.
6. Relocate the door to the designated position. Then screw the bottom hinge assembly on the left designated position and tighten it after the door is leveled. (Fig. 1) 7. Remove the handle from the left side of the door and install it on the right side. (See next section.) INSTALLING THE STAINLESS STEEL HANDLE This appliance includes a stainless steel handle that is not required to operate the unit.
LIGHT The interior light makes it easy to view your items. Touching the LIGHT symbol toggles between 2 modes of operation for the internal lights: functional (default) mode and showcase mode. If you are in functional (default) mode, the lights will turn on only when the door is open. If you are in showcase mode, the lights will be on whether or not the door is open. ºF/ºC SELECTOR Select the temperature display in Fahrenheit or Celsius degrees.
To initiate Sabbath mode, press the POWER and LIGHT keys at the same time for at least 5 seconds. The indicator light will flash four times and confirm the Sabbath mode is ON. Sabbath mode can be exit by repeating the above process. The Sabbath Mode will automatically exit after 96 hours. TEMPERATURE MEMORY FUNCTION In the event of a power interruption (power surge, breaker switch, etc.), the unit can remember the previous temperature settings.
CARE AND MAINTENANCE CLEANING YOUR BEVERAGE MERCHANDISER Turn off the power, unplug the appliance, and remove all items, including shelves. Wash the inside and outside surfaces as well as the shelves with warm water and mild liquid detergent. Rinse well and wipe dry with a clean soft cloth. Wring excess water out of the sponge or cloth when cleaning the area where the controls are located, or any electrical parts. Do not use steel wool or a steel brush on the stainless steel.
TROUBLESHOOTING You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. Troubleshooting Guide PROBLEM Appliance does not operate. Appliance is not cold enough. POSSIBLE CAUSE REMEDY Appliance is not connected to a power source. The appliance is turned off. Tripped circuit breaker or a blown fuse. Connect the appliance. The temperature is not set correctly.
The appliance seems to make too much noise. The door will not close properly. The rattling noise may come from the flow of the refrigerant, which is normal. As each cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your appliance. If temperature fluctuations occur, the contraction and expansion of the inner walls may cause popping and crackling noises. The appliance is not properly level. Level the appliance with the adjustable feet. The appliance is not properly level.
NOTES 14
NOTES 15
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.