RANGE HOODS Models SEH3630 SEH3636 FELIX STORCH, INC. 770 Garrison Avenue Bronx, New York 10474 www.summitappliance.
TABLE OF CONTENTS Safety Warnings................................................................................................2-4 Location of Parts..................................................................................................5 Technical Specifications......................................................................................6 Dimensional Diagram...........................................................................................7 Installation..........................
WIRING DIAGRAM Motor : 420 W / Lamp : 2x50w RED WHITE BLUE BLACK WHITE CAPACITOR CONTROL TROL PANEL WHITE BROWN M LAMP INPUT : 110V AC / 60 Hz WHITE GREEN/YELLOW BLACK ELECTRONIC CIRCUIT SAFETY WARNINGS a. This product is designed for domestic use. b. Electric input for the device must be 110-120 Volt, 60 Hz. c. A grounded cable is installed in your device. It must be connected to a grounded electrical socket. d. All of the electrical installation must be done by a qualified electrician.
v. If the electrical cable is defective, it must be changed by the manufacturer or a qualified service technician. w. If there is a fire, cut off the power to the hood and cooking devices and cover the flame. Do not use water to extinguish the fire. Model SEH3630 Model No 2190.8.579.01 Part No. Spare Part YT971.1000.22 CARBON FILTER YT142.2120.19 YT207.1000.35 ALUMINUM CASSETTE FILTER 3 CABLE FIXER(FOR CHIMNEY HOOD) 4 YT201.1000.21 CIRCUIT BOX 5 YT201.1000.22 CIRCUIT BOX COVER 6 YT202.
EXPLODED VIEW SEH3630 2190.8.579.01 Exploded View For 30" Model 20 15 a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. b. Before servicing or cleaning the unit, switch power off at the service panel and lock the service-disconnecting means to prevent power from being switched on accidentally. If the service-disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. c.
LOCATION OF PARTS Model SEH3636 Model No 2190.9.579.01 Part No. Spare Part YT971.1000.22 CARBON FILTER YT142.2120.06 YT207.1000.35 ALUMINUM CASSETTE FILTER 3 CABLE FIXER(FOR CHIMNEY HOOD) 4 YT201.1000.21 CIRCUIT BOX 5 YT201.1000.22 CIRCUIT BOX COVER 6 YT202.1000.16 METAL VALVE 7 8 YT460.1000.17 YT403.1000.10 BLOWER 9 YT404.1000.24 10 YT455.2120.01 POWER SUPPLY CORD LAMP HOLDER GROUP 11 12 YT456.1001.06 YT457.3110.01 ELECTRONIC CIRCUIT FOR 3 SPEED 13 YT402.1000.02 14 YT410.
EXPLODED VIEW TECHNICAL SPECIFICATIONS SEH3636 2190.9.579.
DIMENSIONAL DIAGRAM WARNING! TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. 11 3 13 16 11 16 3 8 Hood does not operate X Illumination lamp does not illuminate X Check bulbs. (Bulbs should be in good conditions.) Check aluminum filter. (Aluminum cassette filter should be washed once a month under normal conditions.) Check lamp switch. (Lamp switch should be in on position.) Check carbon filter. (If it operates with carbon filter, carbon filter should be replaced quarterly.
REPLACEMENT OF LIGHTING COMPONENTS Disconnect the hood. Remove the aluminum cassette filter. In order to change the 50-watt halogen light bulb, refer to diagram below. (1) Press down on the back part of the lamp holder and (2) turn it counter-clockwise. Replace old bulb with new one. Turn in reverse direction when installing new bulb. INSTALLATION CAUTION: During installation, persons installing the hood must wear heavy gloves to protect against sharp edges.
* Fix the connector box to the motor junction plate with 2 pieces of 3,5 x 9,5 RYSB screws as shown. * * CLEANING AND MAINTENANCE Disconnect the device prior to maintenance (cut off its power supply by turning off the switch). The aluminum cassette filter holds oils and dust from the air. The metal filter must be washed in hot soapy water every month, if possible in the dishwasher at 140°F. To disassemble, press on the spring clamps at the edge of the cassette filter.
OPERATION Peel off protective films from the stainless steel components after assembly. PUSH-BUTTON CONTROLS Your range hood has three levels of ventilation. According to your needs, you can choose a low (|), medium (||) or high (|||) ventilation level by pushing one of the first three buttons on the front panel.
WARNING! TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. Place metal chimneys over product body. D)MOUNTING THE PRODUCT ONTO WALL Hang the product by already mounted -L shaped- hanging parts through covering the body. Screw internal chimney on chimney fixing sheet, fixed over upper corner of external chimney. Fix the body onto the wall with a screw through the (C,D) holes that are located inside the body. A D C B Then fix the body on (A,B) holes to the wall.