RANGE HOOD Model SEH5636G FELIX STORCH, INC. 770 Garrison Avenue Bronx, New York 10474 www.summitappliance.
TABLE OF CONTENTS Safety Warnings................................................................................................2-4 Location of Parts..................................................................................................5 Technical Specifications......................................................................................6 Dimensional Diagram...........................................................................................7 Installation..........................
SAFETY WARNINGS a. This product is designed for domestic use. b. Electric input for the device must be 110-120 Volt, 60 Hz. c. A grounded cable is installed in your device. It must be connected to a grounded electrical socket. d. All of the electrical installation must be done by a qualified electrician. Installations done by unqualified persons may result in poor performance, failure of the device, and accidents. e. Do not let the power cord become pinched or squeezed during installation.
v. If the electrical cable is defective, it must be changed by the manufacturer or a qualified service technician. w. If there is a fire, cut off the power to the hood and cooking devices and cover the flame. Do not use water to extinguish the fire. READ AND SAVE THESE INSTRUCTIONS WARNING! TO REDUCE THE RISK OF A RANGE-TOP GREASE FIRE: a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b.
WIRING DIAGRAM Motor : 420 W / Lamp : 2x50w RED WHITE BLUE BLACK WHITE CAPACITOR CONTROL TROL PANEL WHITE BROWN M LAMP INPUT : 110V AC / 60 Hz WHITE a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. b. Before servicing or cleaning the unit, switch power off at the service panel and lock the service-disconnecting means to prevent power from being switched on accidentally.
LOCATION OF PARTS Model SEH5636G Model No 3150.9.579.01 Part No. Pos. 2 3 4 6 8 5 7 1 2 YT971.1000.22 YT142.3150.06 ALUMINUM CASSETTE FILTER 3 YT207.1000.35 CABLE FIXER(FOR CHIMNEY HOOD) 4 YT201.1000.21 CIRCUIT BOX 5 YT201.1000.22 CIRCUIT BOX COVER 6 METAL VALVE 7 8 YT202.1000.16 YT460.1000.17 BLOWER YT403.1000.10 HALOGEN LAMP-50W 9 YT404.1000.24 POWER SUPPLY CORD 10 11 YT455.3110.01 YT456.1001.06 ELECTRONIC TOUCH BUTTON SET 12 YT457.3110.
EXPLODED VIEW TECHNICAL SPECIFICATIONS SEH5636G 3150.9.579.
DIMENSIONAL DIAGRAM WARNING! TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. 1 4 11 8 5 Hood does not operate X Illumination lamp does not illuminate X Check bulbs. (Bulbs should be in good conditions.) Check carbon filter. (If it operates with carbon filter, carbon filter should be replaced quarterly.) 11 16 Check lamp switch. (Lamp switch should be in on position.) 35 8 1 Check air outlet chimney. (Air outlet chimney should be open.) 19 3 8 Check motor switch.
REPLACEMENT OF LIGHTING COMPONENTS Disconnect the hood. Remove the aluminum cassette filter. In order to change the 50-watt halogen light bulb, refer to diagram below. (1) Press down on the back part of the lamp holder and (2) turn it counter-clockwise. Replace old bulb with new one. Turn in reverse direction when installing new bulb. INSTALLATION CAUTION: During installation, persons installing the hood must wear heavy gloves to protect against sharp edges.
* Fix the connector box to the motor junction plate with 2 pieces of 3,5 x 9,5 RYSB screws as shown. * * CLEANING AND MAINTENANCE Disconnect the device prior to maintenance (cut off its power supply by turning off the switch). The aluminum cassette filter holds oils and dust from the air. The metal filter must be washed in hot soapy water every month, if possible in the dishwasher at 140°F. To disassemble, press on the spring clamps at the edge of the cassette filter.
OPERATION Peel off protective films from the stainless steel components after assembly. PUSH-BUTTON CONTROLS Your range hood has three levels of ventilation. According to your needs, you can choose a low (|), medium (||) or high (|||) ventilation level by pushing one of the first three buttons on the front panel.
WARNING! TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. Place metal chimneys over product body. D)MOUNTING THE PRODUCT ONTO WALL Hang the product on the already-mounted L-shaped hanging parts. Screw internal chimney on chimney fixing sheet, fixed over upper corner of external chimney. Fix the body onto the wall with a screw through the (C,D) holes that are located inside the body. A D C B Then fix the body on (A,B) holes to the wall.