RANGE HOODS Models SEH1524 SEH1536 FELIX STORCH, INC. 770 Garrison Avenue Bronx, New York 10474 www.summitappliance.
TABLE OF CONTENTS Safety Warnings................................................................................................2-4 Location of Parts..................................................................................................5 Technical Specifications......................................................................................6 Dimensional Diagram...........................................................................................7 Installation..........................
SAFETY WARNINGS a. This product is designed for domestic use. b. Electric input for the device must be 110-120 Volt, 60 Hz. c. A grounded cable is installed in your device. It must be connected to a grounded electrical socket. d. All of the electrical installation must be done by a qualified electrician. Installations done by unqualified persons may result in poor performance, failure of the device, and accidents. e. Do not let the power cord become pinched or squeezed during installation.
v. If the electrical cable is defective, it must be changed by the manufacturer or a qualified service technician. w. If there is a fire, cut off the power to the hood and cooking devices and cover the flame. Do not use water to extinguish the fire. READ AND SAVE THESE INSTRUCTIONS WARNING! TO REDUCE THE RISK OF A RANGE-TOP GREASE FIRE: a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b.
WIRING DIAGRAM CAPASITOR Motor: 340W / Lamp: 2X50W Input :110V AC 60 Hz BROWN RED BLUE BLACK BROWN WHITE CONTROL PANEL BLUE BLUE WHITE RED BLACK ( L ) a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. b. Before servicing or cleaning the unit, switch power off at the service panel and lock the service-disconnecting means to prevent power from being switched on accidentally.
LOCATION OF PARTS SEH1536 Model 2121.9.579.01 Model No Pos. 7 9 8 2 6 3 4 4 4 YT971.1000.22 CARBON FILTER YT142.2120.06 ALUMINUM CASSETTE FILTER 3 YT207.1000.35 4 YT201.1000.22 CABLE FIXER(FOR CHIMNEY HOOD) CIRCUIT BOX COVER 5 YT201.1000.24 6 YT202.1000.16 7 8 YT460.1000.16 9 YT404.1000.24 BLOWER HALOGEN LAMP-50W POWER SUPPLY CORD 10 YT455.2120.01 YT458.2120.
EXPLODED VIEW TECHNICAL SPECIFICATIONS SEH1536 2121.9.579.
DIMENSIONAL DIAGRAM WARNING! TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. 7 11 4 1 181 9 43 3 19 Pos. 9 23 1 11 16 7 6 / 35 8 Part No. Spare Part 1 2 YT971.1000.22 CARBON FILTER YT142.2120.03 ALUMINUM CASSETTE FILTER 3 YT207.1000.35 4 YT201.1000.22 CABLE FIXER(FOR CHIMNEY HOOD) CIRCUIT BOX COVER 5 YT201.1000.24 6 YT202.1000.16 7 8 YT460.1000.16 9 YT404.1000.24 BLOWER HALOGEN LAMP-50W POWER SUPPLY CORD 10 YT455.2120.01 YT458.2120.
EXPLODED VIEW INSTALLATION SEH1524 2121.6.579.01 Exploded View For 24" Model 20 15 CAUTION: During installation, persons installing the hood must wear heavy gloves to protect against sharp edges. POSITIONING THE RANGE HOOD Upon completion of installation, the distance between the hood and an electric rangetop must be a minimum of 25" (65cm), and the distance between the hood and a gas rangetop must be a minimum of 30" (75cm). 21 3 12 9 18 6 min. 30" for gas ranges 16 min.
TROUBLESHOOTING If hood does not operate, before contacting customer service: Be sure that the power cable is connected to the power supply and that the electric fuse for the installation is in good condition. Before contacting the service, check your hood according to the table below. If the problem continues, contact your dealer or authorized service center. Troubleshooting Guide Fix the connector box to the motor junction plate with two 3,5 x 9,5 RYSB screws as shown.
REPLACEMENT OF LIGHTING COMPONENTS Disconnect the hood. Remove the aluminum cassette filter. In order to change the 50-watt halogen light bulb, refer to diagram below. (1) Press down on the back part of the lamp holder and (2) turn it counter-clockwise. 3.Fix the suspender screws. Fix the screws to holes A and B.Keep a clearance of 5 mm (0.2") between wall and head of screws in order to hang the hood body easily.Fix the chimney mounting plate to holes E and F by using the screws provided with hood.
OPERATION SPEED CHOICE Product has three-speed motor and a multi-positioned switch to command the motor. For best performance, we recommend you to operate the unit at high speed in excessively smokey and smelly places. Motor starts as the slider switch is opened and stops as the slider set is closed.The slider button at the bottom of the device is for turning the device on. To turn on the device, slide the button to the right.