BUILT-IN TWO-ZONE WINE COOLER Model SWC532LBIST Owner’s Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Write the Serial Number here: _________________________ Felix Storch, Inc. Summit Appliance Division 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Important Safety Instructions ................................................................ 2 – 3 Location of Parts ...........................................................................................4 Installation Instructions .......................................................................... 5 – 7 Before Using Your Wine Cooler ............................................................5 Installation of Your Wine Cooler ..................................................
IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electrical shock or injury when using your appliance, follow these basic precautions • Read all instructions before using the wine cooler. • Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an adapter, and do not use an extension cord. • It is recommended that a separate circuit, serving only your wine cooler, be provided. Use receptacles that cannot be turned off by a switch or pull chain.
the appliance before use. • Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage or discolor the interior. • Do not use this apparatus for other than residential purposes. • This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect.
LOCATION OF PARTS 1. 2. 3. 4. 5. 6. 7. Front vent 8. Adjustable feet 9. Upper hinge 10. Door (with handle and gasket) 11. Lower hinge 12.
INSTALLATION INSTRUCTIONS Before Using Your Wine Cooler Remove the exterior and interior packing. Before connecting the wine cooler to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth. This appliance is especially designed for the storage of wine; do not use it for other purposes.
temperatures may also cause the unit to perform improperly. Avoid locating the unit in moist areas. Do not use an extension cord. Plug the wine cooler into an exclusive, properly installed and grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified or authorized products service center.
NOTE: All parts removed must be saved to allow the door swing to be reversed 1. Carefully use a sharp tool to pry up the decorative cap on the top of the cabinet and the cap of the door spindle. (Fig 1) 2. Open the door about 90°, unscrew the screw of the upper door hinge cover and remove the cover, then unscrew all the screws on the upper door hinge. Be sure to hold the door firmly after removing the screws, and take off the door. (Fig 2) 3.
OPERATING YOUR WINE COOLER The wine cooler should be placed where the ambient temperature is between 61 and 95 degrees Fahrenheit (16-35°C). If the ambient temperature is above or below this range, the performance of the unit may be affected. For example, placing your unit in extremely cold or hot conditions may cause interior temperatures to fluctuate and the range of 41-72 degrees Fahrenheit (5-22°C) may not be reached.
the internal cabinet temperature. The SET temperature is automatically saved. Upper chamber: Temperature setting can be adjusted from 41 to 54°F (5 to 12°C). Lower chamber: Temperature setting can be adjusted from 54 to 72°F (12 to 22°C). To view the SET temperature of either chamber at any time, press the corresponding SET button. The SET temperature will show in the LED display for about 5 seconds, then the current internal temperature for that chamber will reappear.
Storage of Wine Bottles Your wine cooler was designed to store a maximum of 44 bottles in total security. We recommend that you observe the tips below to optimize loading: • Each of the four large shelves can hold 8 bottles, and the two smaller shelves can each hold 6 bottles, arranged as shown here: rear wall rear wall Large shelf Small shelf • Spread your bottles out as evenly as possible over the shelves, so that weight is not concentrated in one spot.
To Remove a Sliding Shelf 1. Remove all bottles from the shelf. 2. Pull the shelf out as far as it will go. 3. Adjust the lever on each side of the shelf, as shown below (down on the left, up on the right) and at the same time, pull the shelf out completely. To raise or lower the position of the shelf, push up the sliding rails, making the front hook out of the shelf bracket, then pull the sliding rails outward to detach them from the shelf bracket. Reverse these steps to install rails in new location.
3. Tape the door shut. 4. Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the appliance with a blanket or similar item. Energy-Saving Tip The wine cooler should be located in the coolest area of the room, away from heat producing appliances and out of direct sunlight.
PROBLEMS WITH YOUR WINE COOLER You can solve many common wine cooler problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling a service technician. TROUBLESHOOTING GUIDE Problem Wine cooler does not operate. Possible Cause Not plugged in. The appliance is turned off. The circuit breaker has tripped or a fuse has blown. Wine cooler is not Check the temperature control settings. cold enough.
NOTES 14
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
