INSTALLATION INSTRUCTIONS BUILT-IN GAS AND ELECTRIC SURFACE UNITS (Cook tops) CABINET OPENING Prepare the cabinet accurately so your unit will fit properly. Below are cabinet cutout dimensions, The dimensions are for the unit to be mounted so the knobs are on the right side. CHECK LOCAL CODES BEFORE MAKING +o Overhead CONNECTIONS. 2h 0 Overhead hl Combustible TT ree Construction SIRES “Connection Area SE an WR SARA < IN STEER 225/4" (LOUELLA) he ~ 28%" {LASSOS} Pa “AT" See CABINET PREPARATIONS Section.
GAS SURFACE UNITS MOUNTING THE BUILT-IN TOP UNIT Place unit in cabinet opening with the valves on the right side. Raise the top by removing top burner valve knobs, and lifting upward on the front edge of the main top. Secure unit to top of cabinets with four No. 8 screws through holes provided in the top flanges of the burner box. The gas pressure regulator supplied must be used with this unit If it is necessary to convert this unit from use with natural gas to L.P,, or L.P.
Manifold Pipe and Burner Valves — Top Buber Pilots Pilot Adjustment Built-in Top Unit with Pilots {Main Burners Not Shown) On units with battery powered ignition, there are no top burner pilots. There are top ignition electrodes in the same location as the top burner pilots. This ignition system requires one (1) § volt alkaline battery for operation. The battery is housed in an enclosure underneath the switch panel cover. It is recommended that you check and/or replace the battery at least once per year.
WIRING DIAGRAM FOR GAS RANGES AND SURFACE UNITS WITH BATTERY EQUIPMENT TEAT ', = Taupe Hf oy on ren sdf | LEADS wo 1) adn T= ih HER ro Ome Een ne oo LEAD cupric aw! 5 1 wires arroyo ode REFER ONLY TO FEATURES WHICH ARE EQUIPPED ON YOUR RANGE 1606-60162 TOP BURNER VALVES Built-in top boomer valves are operated by pressing the knob and truing #t 90 degrees counter-clockwise to the “LITE” position. This position is also the "HI position where maximum gas flow is obtained.
WIRING DIAGRAM FOR GAS SURFACE UNITS AND WALL OVENS BK TOP BURNER IGNITION SWITCHES REAR FRONT IGNITION IGNITION IGNITION MODULE LEAD LEAD MLE OVEN T'STAT OVEN £0 gross mn ti INHERITOR SAFETY VALVE BK £5) M LOOK with TIE 8x @ (Du OVEN LAMP SWITCH \ OVEN LAP WALL PLUG BK.
ELECTRIC SURFACE UNITS MOUNTING THE BUILT-IN TOP UNIT Place unit in cabinet opening with the knobs, on the right side. Raise the top by lifting upward on the front edge of the main top. Secure unit to top of cabinets with four No. 8 screws through holes provided in the top flanges of the boomer box. Make electrical connection. Electrical connection should conform to local requirements and codes.
THREE-WIRE CONDUIT CONNECTION BRANCH id JUNCTION BOX (ACCESS PLATE BLACK REMOVED) LEAD RED LEAD WHITE LEAD . Remove the access plate to gain access to the electrical junction box. 2. Install the thees-wire range conduit and an appropriate strain relief clamp through the Tole in the junction box. . Use an appropriate insulated wire connector to connect the red and black wires from the range conduit to the corresponding ved and black leads from the branch circuit. 4.
WIRING DIAGRAM FOR ELECTRIC RANGES ® 2 L TAT] LIGHT GROUND NOTICE WARNING: FRAME GROUNDED TO NEUTRAL OF APPLIANCE THROUGH & LINK. CODE Unbroken ING THROUGH THE NEUTRAL. DISCONNECT THE LINK FROM THE HERALDIC AND USE GROUNDING TERMINAL OR MELD TO GROUND UNIT IN ACCORDANCE WITH LOCAL CODES. CONNECT NEUTRAL TERMINAL OR LEAD TO BRANCH CIRCUIT NEUTRAL IN USUAL APTER CONSULT MANUFACTURER'S INSTRUCTIONS WHEN CODES, MCGUIRE THAT 3~CONDUCTOR ’ REEL CONED MB LIES.