Use And Care Manual

4. Place the new grinding wheel in position, x it by the
grinding wheel retainer.
NOTE: Examine the grinding wheel and adjust the
tightness of the retainer to make sure the grinding
wheel can rotate freely. DO NOT overtighten the
grinding wheel retainer.
5. Replace the grinding wheel guard, x with the
original screws.
mCAUTION! Never operate a chain saw sharpener
without a proper installed grinding wheel guard.
NOTE: It's recommended to perform a test run for at least
30 seconds with no load before using this product for the rst
time and after changing the grinding wheel. Switch o the
product immediately if the grinding wheel is no longer round
or irregular, considerable vibration occurs or you notice
abnormal noise.
Proper Care for Battery + Charger
mWARNING! To reduce the risk of injury, always unplug
the charger and remove the battery pack from the charger
before performing any maintenance task. Never disassemble
the battery pack or charger. Contact your Snow Joe
®
+
Sun Joe
®
dealer or the Snow Joe
®
+ Sun Joe
®
customer
service center for ALL repairs.
1. To reduce the risk of injury and damage, never immerse
your battery pack or charger in liquid or allow any liquid to
ow inside these components.
2. Clean out dust and debris from charger vents and
electrical contacts by blowing with compressed air.
3. Use only mild soap on a damp cloth to clean the battery
pack and charger, keeping away from all electrical
contacts. Certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Some of
these include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never use
ammable or combustible solvents around battery packs,
battery chargers or tools.
Storage
1. Examine the cordless chain saw sharpener thoroughly for
worn, loose or damaged parts. Should you need to repair
or replace a part, contact an authorized Snow Joe
®
+
Sun Joe
®
dealer or call the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
2. Remove the battery from the cordless chain saw
sharpener before storing.
3. Store the cordless chain saw sharpener indoors in a
locked, dry place out of the reach of children to prevent
unauthorized use or damage.
Battery + Charger O-Season Storage
1. Do not expose your battery pack or charger to water,
rain or allow them to get wet. This could permanently
damage the charger and the battery pack. Do not use oil
or solvents to clean or lubricate your battery pack as the
plastic casing can become brittle and crack, causing a
serious risk of injury.
2. Store the battery pack and charger at room temperature
away from moisture. Do not store in damp locations where
corrosion of terminals may occur. As with other battery
pack types, permanent capacity loss can result if the pack
is stored for long periods of time at high temperatures
(over 120ºF/49ºC).
3. iON+ 24VBAT lithium-ion battery packs maintain their
charge during storage longer than other battery pack
types. As a general practice, it is best to unplug the
battery charger and remove the battery pack when they
are not in use. Recharge the battery pack every 6 months
to 50% capacity (2 lights on) during o-season storage to
maintain optimal battery performance.
Battery Caution + Disposal
Always dispose of your battery pack according to federal,
state, and local regulations. Contact a recycling agency in your
area for recycling locations.
mCAUTION! Even discharged battery packs contain
some energy. Before disposing, use electrical tape to cover
the terminals to prevent the battery pack from shorting, which
could cause a re or explosion.
mWARNING! To reduce the risk of injury or explosion,
never burn or incinerate a battery pack even if it is damaged,
dead or completely discharged. When burned, toxic fumes and
materials are emitted into the surrounding atmosphere.
1. Batteries vary according to device. Consult your manual
for specic information.
2. Install only new batteries of the same type in your product
(where applicable).
3. Failure to insert batteries in the correct polarity,
as indicated in the battery compartment or manual, may
shorten the life of the batteries or cause batteries to leak.
Fig. 21
Unlock
Grinding
wheel retainer
Lock
15