Use and Care Manual

3
• Carry the chain saw by the front handle with the chain saw
switched o and away from your body. When transporting
or storing the chain saw, always t the guide bar cover.
Proper handling of the chain saw will reduce the likelihood
of accidental contact with the moving saw chain.
• Follow instructions for lubricating, chain tensioning and
changing accessories. An improperly tensioned or poorly
lubricated chain may either break or increase the chance
for kickback.
• Keep handles dry, clean and free from oil and grease.
Greasy, oily handles are slippery and can cause loss of
control.
• Cut wood only. Do not use the chain saw for any other
purpose. For example, do not use the chain saw to cut
plastic, masonry or non-wood building materials. Using
the chain saw in these incorrect ways could result in
serious damage to you and your tool.
Causes and Prevention
of Kickback
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut. Tip contact in some cases may cause
a sudden reverse reaction, kicking the guide bar up and back
towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to loose control of the
saw which could result in serious personal injury. Do not rely
exclusively upon the safety devices built into your saw.
As a chain saw user, you should take several steps to keep
your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as detailed below:
• Maintain a rm grip (right hand on the rear handle and
left hand on the front handle with thumbs and ngers
encircling the respective handles) and position your body
and arms to allow you to resist kickback forces. Kickback
forces can be controlled by the operator, if proper
precautions are taken. Do not let go of the chain saw.
• Do not overreach and do not cut above shoulder height.
This helps prevent unintended tip contact and enables
better control of the chain saw in unexpected situations.
• Only use replacement bars and chains specied by the
manufacturer. Incorrect replacement bars and chains may
cause chain breakage and/or kickback.
• Follow the manufacturer’s sharpening and maintenance
instructions for the saw chain. Decreasing the depth
gauge height can lead to increased kickback.
• Always observe the safety regulations and follow the
correct sawing techniques.
• Ensure safe carrying of the chain saw. Whenever the
machine is to be handled or transported, you must:
– switch o the motor, remove the battery and wait for
the chain to stop;
– mount the guide bar cover;
– hold the machine using the hand grips and
position the bar in the opposite direction to that used
during operation.
When using a vehicle to transport the machine, fasten
it rmly and position it so that it is not a danger to any
passengers.
• Before felling or delimbing for the rst time, make sure:
– you have been specically trained to use this type
of equipment;
– you have carefully read the safety regulations and
user instructions contained in this manual;
– you practice rst on logs on the ground or attached to
trestles, in order to get familiar with the machine and
the proper cutting techniques.
Battery & Charger
Safety Instructions
We pay a great deal of attention to the design of every battery
pack to ensure that we supply you with batteries that are safe,
durable and have a high energy density. The battery cells have
a wide range of safety devices. Each individual cell is initially
formatted and its electrical characteristic curves are recorded.
This data is then used exclusively to be able to assemble the
best possible battery packs.
Despite all the safety precautions, caution must always be
exercised when handling batteries. The following points must
be obeyed at all times to ensure safe use. Safe use can only
be guaranteed if undamaged cells are used. Incorrect handling
of the battery pack can cause cell damage.
IMPORTANT! Analyses conrm that incorrect use and poor
care of high-performance batteries are the main factors
responsible for personal and/or product damage.
mWARNING! Use only approved replacement batteries;
other batteries may damage the chain saw and cause it to
malfunction, which can lead to serious personal injury.
mCAUTION! To reduce the risk of injury, charge the
EcoSharp
®
iBAT40 lithium-ion battery pack only in its
designated lithium-ion charger, the iCHRG40. Other types of
chargers present risk of re, personal injury and damage. Do
not wire a battery pack to a power supply plug or car cigarette
lighter. Such misuse will permanently disable or damage the
battery pack.
• Avoid dangerous environments – Do not charge the
battery pack in rain, snow or in damp or wet locations.
Do not use the battery pack or charger in the presence of
explosive atmospheres (gaseous fumes, dust or ammable
materials) because sparks may be generated when inserting
or removing the battery pack, which could lead to a re.