Use and Care Manual

5. To re-install the blade, position the blade with the
cutting edges toward the ground. Assemble the blade,
the square washer, and the blade nut as shown in the
following. Using a 15-mm wrench or socket, turn the
blade nut “CLOCKWISE” to secure the blade.
NOTE: Be sure to replace the parts in the exact order in
which they were removed. When installing the cutting blade,
verify that it is installed with the curved ends pointing toward
the mower deck.
Clean the Mower
m WARNING: To reduce the risk of electric shock, do not
expose the mower to water.
The underside of mower deck should be cleaned after each
use as grass clippings, leaves, dirt and other debris will
accumulate causing rust and corrosion.
Remove any buildup of grass and leaves on or around the
motor cover (do not use water). Wipe the mower clean with a
dry cloth occasionally.
• If debris build up on the underside of the unit while using,
stop the motor and disconnect it from the power supply.
Tilt the mower forward, or on its side, and scrape it clean
with an appropriate tool.
Storage
The following steps should be taken to prepare the lawn
mower for storage.
• Make certain the power is disconnected.
• Clean mower as instructed in previous section.
• Inspect and replace/sharpen blade, if required. Refer to
the Maintenance section.
• Store mower in a dry, clean area. Do not store next to
corrosive materials, such as fertilizer and rock salt.
• Wipe extension cord to remove any foreign substances
such as oil or stains. Replace extension cord if cut or
damaged in any way.
• Wind the cord in a series of equal loops to prevent it
from tangling.
• Store mower indoors, in a cool, dry place, out of reach
of children. Do not cover lawn mower with a solid plastic
sheet. Plastic coverings trap moisture around the mower
causing corrosion.
• The handle may be folded away completely for storage.
• Loosen the handle knobs on the sides of the handle, and
fold the upper handle down.
• Loosen the handle knobs, pull outwards on each side of
the lower handle, and lift the sides of the lower handle past
the edges of the handle mounting brackets. Fold the lower
handle forward. Make sure not to bend or kink the power
cord.
• When cutting thick grass, reduce walking speed in order to
allow for a more effective cut and a proper discharge of the
clippings. For a healthy lawn, always cut off one-third or less
of the total length of the grass. The average lawn should be
approximately 1-1/2 to 2 in. (3.8 to 5 cm) long during cool
month, and more than 2 in. (5cm) long during hot months. If
there is growth, the lawn should be cut in the fall.
Mulching Tips
NOTE: INSPECT THE AREA WHERE THE MOWER IS TO
BE USED AND REMOVE ALL THE STONES, STICKS, WIRES
AND OTHER DEBRIS THAT MIGHT BE THROWN BY THE
ROTATING BLADE.
1. Release the switch to turn the mower off when crossing
any graveled area (stone can be thrown by the blade).
2. Set mower to the highest cutting height when mowing
on uneven ground or in tall weeds.
3. For effective mulching, do not cut wet grass, because it
tends to stick to the underside of the deck, preventing
proper mulching of grass clippings. New or thick grass
may require a narrower cut. The ground speed should
be adjusted to the condition of the lawn. If mowing has
been delayed and the grass has been allowed to grow
longer than 4 in. (10 cm), mow the lawn twice in order
to reduce the grass to the maximum of 3 -1/4 in. (8.3
cm).
4. Walk at a steady pace. Overlap the cutting rows. Do
not let the grass get too tall. If the grass gets too long,
start at the highest cutting position and work down to
the desired cutting height.
m WARNING: If you strike a foreign object, stop the
motor and disconnect the power cord. Thoroughly inspect the
mower for any damage. Repair any damage before operating
the mower.
Cutting Blade Replacement
(Fig. 9 & Fig. 10)
m WARNING: Always protect your hands by wearing
heavy gloves and/or wrapping the cutting edges with rags
or other materials when performing any maintenance on the
blades.
1. Release the switch lever to turn the mower OFF, wait
for the blade to come to a complete stop.
2. While wearing leather padded gloves, wedge a block
of wood between the blade and the mower deck in
order to prevent the blade from turning when the nut is
being removed.
3. Using a 15-mm wrench or socket, loosen the blade
nut (1) “COUNTERCLOCKWISE” to loosen it and
“CLOCKWISE” to tighten it.
4. Remove the blade nut (1), the square washer (2), and
the blade (3).
8
Fig. 10
Fig. 9
Tighten
Loosen
3
2
1