Instructions / Assembly

ManualsBrandsSun-Mar ManualsKitchenElongated Dry Toilet Non-Electric Waterless Toilet

INSTALLING THE SUN-MAR DRY TOILET

- 5 –

Placement

Of The

SUN-MAR

Dry Toilet

Installing

The

SUN-MAR

Dry Toilet

Base

The

Transition

Piece

Ensure that the floor joists are not in the way and that there is an unobstructed 10”

diameter passage from the underside of the AF “Dry Toilet” to the top of the transition

piece. The 10” hole should be centered 11.5” (29.21 cm) from the back wall and at least

9” (22.86 cm) dry toilet from the side wall in the room where the toilet will be installed.

The transition piece on the top of the composting unit should be located so that the

center line of the transition piece is directly below the center of the 10” circular cutout

which will be made in the bathroom floor above. The transition piece should be at a right

angle to the composting unit.

The SUN-MAR Dry Toilet comes preassembled. For the purpose of

explanation, the toilet base is the bottom of the toilet which is

secured to the bathroom floor, the toilet chute is the black inner

section (shown in Fig. A) that fits through the floor and is attached

to the toilet top, the toilet top is the upper part of the toilet that

attaches to the toilet base, and the bowl liner which is the black

removable funnel shaped piece below the toilet seat.

To install the SUN-MAR Dry Toilet, follow the procedure outlined

below:

1. To locate the position of the SUN-MAR Dry Toilet, place the toilet

chute in the desired location on the floor in the bathroom and

trace the 10”(25 cm) diameter cut out in the bottom of the toilet

base on the floor in the bathroom. The centre of the 10” circle

should be centered 11.5” (29.21 cm) from the wall against which

the toilet will be mounted(See Fig. A)

2. Drill a 1/2”(6mm) hole on the front of traced line and then check

under the floor that the hole will be clear of floor joists and will

line up with the composting unit below. (See Fig. B)

3. If the position is correct, complete the cutting of the10”(250mm)

diameter circle with a jig saw. (See Fig. C)

4. Center the toilet base over the 10”(250mm) diameter hole that

Has been cut out of the floor and securely attach to the floor by

using the four 5/16” by 2 1/2”(8mm by 64mm) lag bolts that are

provided with your kit. (See Fig. D)

**Prior to finishing the SUN-Mar Dry Toilet installation, it is a good

Idea at this time to do a pre-assembly check to see if you will

need any extension pipe.

Place transition piece (Fig. E) into the rectangular opening on the

top of the composting unit. Make sure that the transition piece is

completely vertical on the unit, or completely vertical. Important: the

transition piece should be completely vertical. The opening in the

toilet in bathroom should be oriented above the opening in the

transition piece so that waste can drop directly into the patented

bio-drum.

Summary of content (2 pages)

PAGE 1
INSTALLING THE SUN-MAR DRY TOILET Placement Of The SUN-MAR Dry Toilet Installing The SUN-MAR Dry Toilet Base The Transition Piece Ensure that the floor joists are not in the way and that there is an unobstructed 10” diameter passage from the underside of the AF “Dry Toilet” to the top of the transition piece. The 10” hole should be centered 11.5” (29.21 cm) from the back wall and at least 9” (22.86 cm) dry toilet from the side wall in the room where the toilet will be installed.
PAGE 2
Determining If An Extension Pipe Piece Is Required Assembling And Installing The Extension Pipe Pieces Finishing The SUN-MAR AF Dry Toilet Base Installation Place the toilet chute into the toilet base in the bathroom. If the toilet chute extends 1- 7 piece, 2”(25 - 50mm) into the transition then no extension pipe pieces will be required. If the transition piece does not extend far enough up to meet the toilet chute, then one or more extension pipe pieces will be needed.