Netra™ 1290 Server Installation Guide Sun Microsystems, Inc. www.sun.com Part No. 819-4372-10 May 2006, Revision A Submit comments about this document at: http://www.sun.
Copyright 2006 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc. has intellectual property rights relating to technology that is described in this document. In particular, and without limitation, these intellectual property rights may include one or more of the U.S. patents listed at http://www.sun.com/patents and one or more additional patents or pending patent applications in the U.S. and in other countries.
Contents Preface 1.
Connecting Consoles to the System Controller Connecting the I/O Assemblies 37 Installing Additional Hardware 37 Installing Additional Peripheral Devices 2. Setting Up 34 38 39 Setup Process 39 Setting Up the Hardware On/Standby Switch 40 40 Disabling Operation of the On/Standby Switch Powering On the Server 41 Bringing the Server to Standby Mode Setting Up the Server 42 44 Installing and Booting the Solaris Operating System Installing the Lights Out Management Packages A.
Figures FIGURE 1-1 Opening the Shipping Carton 2 FIGURE 1-2 Removing the Carton Pieces 3 FIGURE 1-3 Slide Rail Assembly (Standard Configuration) FIGURE 1-4 Spring Clips and Cutouts FIGURE 1-5 Slide Rail Assembly–Modified for 2-Post Installation FIGURE 1-6 Installing the Slide Rails in a Sun Fire Cabinet FIGURE 1-7 Installing the Rails in a Sun Rack 900 Cabinet or 19-Inch Four-Post Cabinet FIGURE 1-8 Releasing the Door Hinge Mechanism FIGURE 1-9 Removing the Shipping Cradle Bolts FIGURE
FIGURE 1-21 Attaching the Upper CMA Arm and Pivot Bracket 28 FIGURE 1-22 Attaching the Lower CMA Arm and Pivot Bracket 29 FIGURE 1-23 Attaching the Left-Hand T-Bracket FIGURE 1-24 Attaching the Right-Hand T-Bracket FIGURE 1-25 Attaching the Upper and Lower CMA Arms to the T-Bracket FIGURE 1-26 System Controller and I/O Assembly Locations FIGURE 2-1 Netra 1290 Server On/Standby Switch FIGURE A-1 External I/O Connection Locations FIGURE A-2 68-Pin SCSI Connector FIGURE A-3 DB-15 (Male) Al
Tables TABLE A-1 68-Pin SCSI Connector Pinout 55 TABLE A-2 68-Pin SCSI Connector Pinout (continued) TABLE A-3 Alarms Service Port Connector Pinout TABLE A-4 RJ-45 Gigabit Ethernet Connector Pinout TABLE A-5 Twisted-pair Ethernet Connector Pinout TABLE A-6 TPE STP-5 Cable Lengths TABLE A-7 RJ-45 Serial Connector Pinout TABLE A-8 Default Settings for Connecting to LOM Serial A TABLE A-9 Pin Interconnections Performed by the Sun DB-25 Adapter TABLE A-10 Pin Interconnections Performed by a
viii Netra 1290 Server Installation Guide • May 2006
Preface The Netra 1290 Server Installation Guide provides detailed procedures that describe the installation, power-on, and configuration of the Netra™ 1290 server into a rack. This document is written for technicians, system administrators, authorized service providers (ASPs), and users who have experience installing and configuring computer hardware. How This Document Is Organized Chapter 1 describes how to unpack your server and install it into a cabinet or rack.
Shell Prompts Shell Prompt C shell machine-name% C shell superuser machine-name# Bourne shell and Korn shell $ Bourne shell and Korn shell superuser # Typographic Conventions Typeface* Meaning Examples AaBbCc123 The names of commands, files, and directories; on-screen computer output Edit your.login file. Use ls -a to list all files. % You have mail.
Related Documentation The documents listed as online are available at: http://www.sun.
Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions. You can submit your comments by going to: http://www.sun.
CHAPTER 1 Unpacking and Installing the Server This chapter describes unpacking and installing the Netra 1290 server into a rack.
Shipping kit Carton protection pads Bands FIGURE 1-1 Opening the Shipping Carton 4. Cut the bands from the outer packaging and open the carton. See FIGURE 1-1. 5. Remove and unpack the shipping kit. See FIGURE 1-2.
Shipping kit Outer carton Internal saddle FIGURE 1-2 Removing the Carton Pieces 6. Remove the outer carton. See FIGURE 1-2.
7. Remove the internal saddle. See FIGURE 1-2. 8. Lift off the server bag. 9. Make a visual check to ensure that the chassis is undamaged. 10. Move the server to the operating location using a computer lifting device. Note – Power cords for the Netra 1290 server are supplied in a separate country kit. Note – The Solaris software and the LOM firmware are preinstalled or preconfigured on the server.
This section is divided into the following: ■ ■ ■ ■ ■ ■ ■ “Adjusting the Slide Rail Assembly” on page 5 “To Install the Inner Rails on the Server” on page 6 “To Prepare the Rails for 2-Post Installations” on page 8 “Installing the Slide Rail Assemblies in a Sun Fire or Sun StorEdge Cabinet” on page 9 “Installing the Slide Rail Assemblies in a Sun Rack 900 Cabinet” on page 11 “Installing the Slide Rail Assemblies in a 19-Inch 4-Post Cabinet” on page 13 “Installing the Slide Rail Assemblies in a 19-Inch 2-P
Adjust the rear bracket or the adjustable bracket position to modify the length of the assembly. The slide rail assembly and the rear bracket have bracket locations for specific cabinets stamped onto the metal. FIGURE 1-3 shows the location of the markings. ▼ To Install the Inner Rails on the Server 1. Remove the inner rail from the slide rail assembly: a. Press the latch adjacent to the green latch. b. Pull the inner rail free from the outer slide rail assembly. 2.
FIGURE 1-4 Spring Clips and Cutouts The spring clip should engage. Note – The spring clips must be above the system hooks. The lip on the main body of the inner rail must engage under and behind the system hook. 3. Secure the inner rail to the server using two 5 x 10 mm screws for each rail.
4. Repeat Step 1 through Step 3 for the second inner rail. ▼ To Prepare the Rails for 2-Post Installations For 2-post installations, you can dismantle and reassemble the slide rail assemblies (FIGURE 1-5). The slide rail assemblies can be adjusted to suit a 19-inch 2-post rack that has a post depth in the range of 3 to 6 inches (7.5 to 15.0 cm).
Installing the Slide Rail Assemblies in a Sun Fire or Sun StorEdge Cabinet Sun Fire™ and Sun StorEdge™ cabinets have No. 10-32 UNF tapped screw holes in the front and rear, which are numbered from bottom to top. Note – The slide rail assemblies are reversible. They can be used on either side of the cabinet. ▼ To Install the Slide Rail Assemblies in the Bottom Position 1. Adjust the position of the adjustable bracket on each slide rail assembly. a. Loosen the two nuts that secure the adjustable bracket. b.
3. Insert the pins in the front bracket into cabinet holes 22 and 33 (FIGURE 1-6). Front bracket secured to outer cabinet holes FIGURE 1-6 Adjustable bracket secured to inner cabinet holes Installing the Slide Rails in a Sun Fire Cabinet The pins hold the bracket in place until the bracket is secured. 4. Secure the adjustable bracket into cabinet holes 24 and 31 with two No. 10-32 UNF screws. 5. Secure the front bracket into cabinet holes 24 and 31 with two No. 10-32 UNF screws. 6.
a. Loosen the four nuts that secure the rear bracket. b. Reposition the rear bracket to the location marked “Sun Fire Cabinet” on the slide rail assembly and secure the rear bracket. 3. Insert the pins in the front bracket into cabinet holes 58 and 69 (FIGURE 1-6). The pins hold the bracket in place until it is secured. 4. Secure the adjustable bracket into cabinet holes 60 and 67 with two No. 10-32 UNF screws. 5. Secure the front bracket into cabinet holes 60 and 67 with two No. 10-32 UNF screws. 6.
a. Loosen the four nuts that secure the rear bracket. b. Reposition the rear bracket to the location marked “NGR Cabinet” on the slide rail assembly and secure the rear bracket. 3. Insert the pins in the front bracket into cabinet holes 22 and 33 (FIGURE 1-7). Front bracket secured to outer cabinet holes FIGURE 1-7 Rear bracket secured to outer cabinet holes Installing the Rails in a Sun Rack 900 Cabinet or 19-Inch Four-Post Cabinet The pins will hold the bracket in place until the bracket is secured.
▼ To Install the Slide Rail Assemblies in the Top Position 1. Remove the adjustable bracket on each rail. a. Loosen the two nuts that secure the adjustable bracket. b. Discard the adjustable bracket. 2. Adjust the length of each slide rail assembly. a. Loosen the four nuts that secure the rear bracket. b. Reposition the rear bracket to the location marked “NGR Cabinet” on the slide rail assembly and secure the rear bracket. 3. Insert the pins in the front bracket into cabinet holes 58 and 69 (FIGURE 1-7).
b. Discard the adjustable bracket. 2. Adjust the length of each slide rail assembly. a. Loosen the four nuts that secure the rear bracket. b. Reposition the rear bracket to the appropriate markings shown on the slide rail assembly and secure the rear bracket. 3. Secure the rear bracket with two No. 10-32 UNF screws (FIGURE 1-7). ■ To install the server in the lowest position, insert the rackmount securing screws no lower than 18.5 inches and 22.5 inches (47.0 cm and 57.2 cm) respectively.
▼ To Install the Slide Rail Assemblies in a 19-Inch 2-Post Rack 1. Secure the front bracket with two No. 10-32 UNF screws. Insert the rackmount securing screws no lower than 18.5 inches and 22.5 inches (47.0 cm and 57.2 cm) respectively. Note – Mounting the bracket no lower than 18.5 inches and 22.5 inches allows for 10 inches of space beneath the server in order to service the backplane. 2. Secure the rear bracket with two No. 10-32 UNF screws. 3.
c. Repeat Step a and Step b for the second front bezel door. FIGURE 1-8 Releasing the Door Hinge Mechanism 2. Remove the shipping cradle bolts (FIGURE 1-9). The bolts secure the orange metal shipping cradle to the wooden pallet.
F R O N T FIGURE 1-9 ▼ Removing the Shipping Cradle Bolts To Mount the Server in the Cabinet Caution – The Netra 1290 server with shipping cradle weighs approximately 286.0 lb (130.0 kg). To prevent personal injury, two people are needed to move the server safely into the cabinet using a computer equipment lift. 1. Extend the cabinet stabilizer and lock it in position (as applicable).
Caution – The shipping cradle must be attached when the server is lifted. Failure to do so will result in major damage to the server. 2. Insert the forks of the lifting device fully through the shipping cradle opening (FIGURE 1-10). F R O N T FIGURE 1-10 Inserting the Lifting Device Into the Shipping Cradle 3. Lift the server off the wooden shipping pallet and remove the pallet. 4. Extend the outer rails from the cabinet and latch them in the extended position. 5.
Outer rails Inner rails FIGURE 1-11 Aligning the Rails Chapter 1 Unpacking and Installing the Server 19
Caution – The cabinet stabilizers (if applicable) must be extended or the cabinet might topple when the lifting device is withdrawn. 7. With the lifting device still supporting the server, loosen the four captive screws attaching the handles of the shipping cradle to the server. 8. Loosen the four captive screws that attach the handles to the shipping cradle. 9. Pull both shipping cradle handles away from the server. This disconnects the shipping cradle from the server. 10.
11. Press the green latches on each rail and push the server into the cabinet (FIGURE 1-13). FIGURE 1-13 Pushing the Server Into the System Cabinet 12. Tighten the two securing screws on the front of the server to secure the server in the cabinet (FIGURE 1-14). Securing screw FIGURE 1-14 Securing screw Tightening the Securing Screws 13. Retract the cabinet stabilization mechanism (as required).
14. Reattach the front doors of the server. Installing Slide Rail Lock Nuts Note – Slide rail lock nuts are preinstalled on all units shipped from the factory in a cabinet. For servers not shipped preinstalled in a cabinet, a slide rail mounting kit containing lock nuts, spacers, and rails is used to mount and secure a server in a cabinet. See “Installing Slide Rails” on page 4.
FIGURE 1-15 Inserting and Tightening the Spacers 5. Slide the server into the system cabinet. 6. From the rear of the server, insert and tighten the lock nuts, one for each rail (FIGURE 1-16). FIGURE 1-16 Inserting and Tightening the Lock Nut 7. Repeat Step 1 through Step 6 for each server in the system cabinet. 8. Retract the cabinet stabilization mechanism (as required).
Installing the Cable Management Arm This section contains the following topics: ■ ■ “To Install the CMA–Lite” on page 25 “To Install the CMA–800” on page 26 The cable management arm (CMA) supports and protects cables when a server slides into or out of a cabinet. Two cable management arm solutions are offered – CMA-Lite and CMA-800. The choice of CMA depends on the available depth in the cabinet and the quantity or type of cable to be supported.
▼ To Install the CMA–Lite 1. Secure the pivot at the end of the upper arm to the top rear of the server, using the two captive screws (FIGURE 1-18). 2. Secure the center pivot point of the CMA to the inside rear of the left hand slide rail assembly, using the two captive screws. 3. Secure the pivot at the end of the lower arm to the bottom rear of the server, using the two captive screws.
▼ To Install the CMA–800 Refer to FIGURE 1-19, throughout the following procedure for identification of CMA parts. Hinge pin Upper pivot bracket Upper CMA arm Guide bar Hinge pin Lower pivot bracket Left hand T-bracket Guide slot Right hand T-bracket Guide slot Lower CMA arm FIGURE 1-19 Guide bar Upper and Lower CMA Arms, and Left-Hand and Right-Hand T-Brackets Note – In the following procedure all left-hand and right-hand orientation is as viewed from the rear of the server chassis.
1. Remove the hinge pin securing the pivot bracket to the upper CMA arm, which facilitates attaching the bracket to the server chassis. 2. Secure the pivot bracket to the upper left-hand side of the server chassis using the two captive screws. See FIGURE 1-20 and FIGURE 1-21.
Hinge pin Upper pivot bracket Upper CMA arm FIGURE 1-21 Attaching the Upper CMA Arm and Pivot Bracket 3. Remove the hinge pin securing the pivot bracket to the lower CMA arm, which facilitates attaching the bracket to the server chassis. 4. Secure the pivot bracket to the lower left-hand of the server chassis using the two captive screws. See FIGURE 1-20 and FIGURE 1-22.
Hinge pin Lower pivot bracket Lower CMA arm FIGURE 1-22 Attaching the Lower CMA Arm and Pivot Bracket 5. After attaching the bracket to the chassis, secure the lower CMA arm to the bracket using the hinge pin removed previously. 6. Secure the left hand T-bracket to the left hand slide rail using two captive screws, FIGURE 1-23.
Slide rail Left hand T-bracket FIGURE 1-23 Attaching the Left-Hand T-Bracket 7. Secure the right-hand T-bracket to the right-hand slide rail using two captive screws (FIGURE 1-24).
Slide rail Right hand T-bracket FIGURE 1-24 Attaching the Right-Hand T-Bracket 8. Secure the upper CMA arm to the left-hand T-bracket using a single hinge pin (FIGURE 1-25).
Hinge pin Guide bars Hinge pin Left hand T-bracket Right hand T-bracket FIGURE 1-25 Attaching the Upper and Lower CMA Arms to the T-Bracket 9. Secure the lower CMA arm to the left-hand T-bracket using a single hinge pin (FIGURE 1-25). 10. Route the cabling through the cable channels as desired. 11. Secure both the upper and lower CMA arms by inserting the guide bars of each arm into the slots provided on the right-hand T-bracket.
Connecting Power Cables Caution – The Netra 1290 server is designed to work with power systems having a grounded neutral conductor. Do not connect the equipment into any other type of power system. Contact your facilities manager or a qualified electrician to determine what type of power is supplied to your building. Caution – The Netra 1290 server is shipped with grounding-type (three-wire) power cords. Always connect the cords into grounded power outlets.
Note – It is the installer’s responsibility to ensure that the cabinet has sufficient electrical power and redundancy to handle the required installation. ■ If the server is mounted in an unpowered cabinet: a. Connect power cords from Source A on the server to the customer-supplied power source A circuit breakers. b. Connect power cords from Source B on the server to the customer-supplied power source B circuit breakers. ■ If the server is mounted in a powered cabinet: a.
LOM Serial A port connects directly to an ASCII terminal or a network terminal server (NTS) using a command-line interface. This port is used for the initial administrative console. Use this port to modify the default system controller settings so that the 10/100BASE-T LOM Ethernet port can be used as an administrative console. The configuration of Serial port A cannot be changed. See Appendix A for details on the serial ports.
PCI+ 0-5 slots SCSI port, 68 pins 10/100BASE-T LOM/SC port Alarms port LOM Serial A port NET0 and NET1 ports Serial B port FIGURE 1-26 ▼ System Controller and I/O Assembly Locations To Connect the Administrative Console Once the initial configuration is complete, you can perform system administration tasks directly or over the network using the 10/100BASE-T LOM Ethernet port. Note – Communication on the LOM Serial A port is possible but is subject to interruption by the LOM device.
Connecting the I/O Assemblies The I/O assemblies provide network interface and peripheral access to the system domains. ▼ To Connect the I/O Assemblies 1. Connect one end of the I/O Ethernet cable to the NET0/NET1 Ethernet port (FIGURE 1-26). 2. Connect the other end of the I/O Ethernet cable to the hub, workstation, or peripheral.
additional information refer to: http://www.sun.com/io Installing Additional Peripheral Devices When you add additional storage devices, refer to the Rackmount Placement Matrix, at http://docs.sun.com, for the mounting hole numbers of the mounting screws for Sun Microsystems disk arrays, other storage trays, and devices. Unless otherwise specified in the Rackmount Placement Matrix, mount the heaviest subassemblies at the lowest available opening.
CHAPTER 2 Setting Up This chapter describes how to power on your server using the system controller command-line interface (LOM prompt), how to set up the SC using the setupnetwork command, and how to boot the Solaris Operating System.
8. Booting the Solaris Operating System. 9. Installing the Lights Out Management packages from the Sun Microsystems software download center. Setting Up the Hardware ▼ To Install and Cable the Hardware 1. Connect a terminal to the system controller board serial port (FIGURE 1-26). 2. Set up the terminal to use the same baud rate as the SC serial port.
2.0.1 Disabling Operation of the On/Standby Switch ● To disable the On/Standby switch, use the setupsc command. lom>setupsc System Controller Configuration ------------------------------SC POST diag Level [off]: Host Watchdog [enabled]: Rocker Switch [enabled]:disabled Secure Mode [off]: Powering On the Server When all the power cables are connected and the external circuit breakers are switched on, the server enters Standby mode.
The server powers on completely. The System Active indicator illuminates and the server executes the power-on self-test (POST). ▼ To Power On Using the LOM poweron Command ● At the lom> prompt, type: lom>poweron The SC first powers on all the power supplies, followed by the fan tray. Finally the SC powers on the system boards. If the value of the OpenBoot PROM variable auto-boot? is true then the server also boots the Solaris Operating System.
▼ To Bring the System to Standby Mode From the Solaris Command Line ● At the system prompt, type: # shutdown -i5 ▼ To Bring the System to Standby Mode From the LOM Port ● At the lom> prompt, type: lom>shutdown ● For an abrupt power off, type: lom>poweroff This will abruptly terminate Solaris. Do you want to continue? [no] Caution – This abruptly brings the system to Standby mode, regardless of the system state and might corrupt data on the hard drives.
● For an abrupt power off, press the left side of the On/Standby switch and hold it for at least four seconds. Caution – This abruptly brings the system to Standby mode, regardless of the system state and might corrupt data on the hard drives. Setting Up the Server After powering on, you must set up your server using the SC setdate and setupnetwork commands described in this section.
2. At the Enter new password prompt, type your password. 3. At the Enter new password again prompt, re-type your password. lom>password Enter new password: Enter new password again: lom> If your password has been lost or forgotten, contact Sun Service for assistance. ▼ To Configure Network Parameters The Netra 1290 server can be administered from the SC LOM prompt and from the Solaris software.
CODE EXAMPLE 2-1 Output From the setupnetwork Command lom> setupnetwork Network Configuration --------------------Is the system controller on a network? [yes]: Use DHCP or static network settings? [static]: Hostname [hostname]: IP Address [xxx.xxx.xxx.xxx]: Netmask [xxx.xxx.xxx.x]: Gateway [xxx.xxx.xxx.xxx]: DNS Domain [xxxx.xxx.xxx]: Primary DNS Server [xxx.xxx.xxx.xx]: Secondary DNS Server [xxx.xxx.xx.
2. To power on the server, type poweron. Depending on the setting of the OpenBoot PROM auto-boot? parameter, the server attempts to boot the Solaris Operating System (OS) or remains at the OpenBoot PROM ok prompt. The default setting is true, which attempts to initiate a boot into the Solaris OS. If the setting of auto-boot? is false or there is no bootable Solaris image installed, then you the OpenBoot PROM ok prompt is returned. lom>poweron . . . . . . ok 3.
These packages are available from the Solaris software download center at: http://www.sun.com/download/ Under Systems Administration, click on the Systems Management link. Note – The latest patches to these packages is available from SunSolve in patch 110208. It is strongly advised that the latest version of patch 110208 be obtained from SunSolve and be installed on the Netra 1290 server to make use of the latest LOM utility updates.
CODE EXAMPLE 2-2 Installing the LOM Drivers (Continued) i.drivers (INFO): Installing /var/tmp/SUNWlomr/reloc/platform/sun4u/kernel/drv/sparcv9/lomv i.drivers (INFO): Identified drivers ’lom lomp lomv’ i.drivers (INFO): Cleaning up old driver ’lom’... Cleaning up old devlink entry ’type=ddi_pseudo;name=SUNW,lom i.drivers (INFO): Cleaning up old driver ’lomp’... Cleaning up old devlink entry ’type=ddi_pseudo;name=lomp i.drivers (INFO): Cleaning up old driver ’lomv’...
Note – The warning messages concerning lomp, lomv, and lom driver attachment seen during the installation of the SUWNlomr package can be safely ignored since the SUNWlomr package is not used on the Netra 1290 server. However, the presence of the package is required to enable successful upgrade through future patches. ▼ To Install the LOM Utility ● As superuser, type: CODE EXAMPLE 2-3 Installing the LOM Utility # pkgadd -d .
CODE EXAMPLE 2-4 Installing the LOM Manual Pages # pkgadd -d . SUNWlomm Processing package instance from LOMlite manual pages (sparc) 2.0,REV=2000.08.22.14.14 Copyright 2000 Sun Microsystems, Inc. All rights reserved. Using as the package base directory. ## Processing package information. ## Processing system information. 5 package pathnames are already properly installed. ## Verifying disk space requirements. ## Checking for conflicts with packages already installed.
52 Netra 1290 Server Installation Guide • May 2006
APPENDIX A Netra 1290 Server Connections This appendix describes the cables and connectors available to complete the installation.
PCI+ 0-5 slots SCSI port, 68 pins 10/100BASE-T LOM/SC port Alarms port LOM Serial A port NET0 and NET1 ports Serial B port FIGURE A-1 External I/O Connection Locations PCI+ IB_SSC Assemblies Note – Do not mix different cards with different speeds within an IB6 leaf (two paired slots), because leaf slots run at the lowest speed and the lowest mode for a given set of cards within a leaf.
SCSI Connector The SCSI connector is a 68-pin SCSI connector (FIGURE A-2). TABLE A-1 lists the pinout information. 34 68 SCSI3 FIGURE A-2 TABLE A-1 1 35 68-Pin SCSI Connector 68-Pin SCSI Connector Pinout Pin No. Signal Name Type Pin No. Signal Name Type Pin No.
TABLE A-2 68-Pin SCSI Connector Pinout (continued) Pin No. Signal Name Type Pin No. Signal Name Type Pin No.
TABLE A-3 Alarms Service Port Connector Pinout Pin Signal Name Description State 1 Not connected 2 Not connected 3 Not connected 4 Not connected 5 SYSTEM_NO UNIX® Running Normally open 6 SYSTEM_NC UNIX Running Normally closed 7 SYSTEM_COM UNIX Running Common 8 ALARM1_NO Alarm1 Normally open 9 ALARM1_NC Alarm1 Normally closed 10 ALARM1_COM Alarm1 Common 11 ALARM2_NO Alarm2 Normally open 12 ALARM2_NC Alarm2 Normally closed 13 ALARM2_COM Alarm2 Common 14 Not c
1 NET 0 8 1 NET 1 8 FIGURE A-4 RJ-45 Gigabit Ethernet Connectors TABLE A-4 RJ-45 Gigabit Ethernet Connector Pinout Pin Signal Name Pin Signal Name 1 TRD0_H 5 TRD2_L 2 TRD0_L 6 TRD1_L 3 TRD1_H 7 TRD3_H 4 TRD2_H 8 TRD3_L 10/100BASE-T LOM Ethernet Port The 10/100BASE-T LOM Ethernet port is an RJ-45 twisted-pair Ethernet (TPE) connector (FIGURE A-5). This port is also known as the system controller Ethernet port. TABLE A-5 lists the pinout information.
TABLE A-5 Twisted-pair Ethernet Connector Pinout Pin Description Pin Description 1 TXD+ 5 Common mode termination 2 TXD– 6 RXD– 3 RXD+ 7 Common mode termination 4 Common mode termination 8 Common mode termination Twisted-Pair Ethernet Cable-Type Connectivity The following types of TPE cables can be connected to the 8-pin TPE connector: ■ For 10BASE-T applications, shielded twisted-pair (STP) cable: ■ Category 3 (STP-3, voice grade) ■ Category 4 (STP-4) ■ Category 5 (STP-5, data grade)
8 1 LOM Serial A 8 1 Serial B FIGURE A-6 RJ-45 Serial Connectors TABLE A-7 RJ-45 Serial Connector Pinout Pin Signal 1 RTS 2 DTR 3 TXD 4 Signal Ground 5 Signal Ground 6 RXD 7 DSR 8 CTS Note – Serial port B is reserved. TABLE A-8 lists the settings needed to use the LOM Serial A connection. The configuration of this port cannot be changed. Be sure to check the manufacturer’s documentation for your specific terminal server.
Using a DB-25 Adapter for Your Serial Link To connect from a terminal, use either the DB-25 (25-Pin DSUB male to 8-POS RJ-45 female) adapter supplied with your server (part number 530-2889) or an alternative adapter that performs the same pin interconnections. The Sun supplied DB-25 adapter enables you to connect to most Sun system. TABLE A-9 lists the pin interconnections the DB-25 adapter performs.
62 Netra 1290 Server Installation Guide • May 2006
Index A connectivity, 59 adjusting slide rails, 5 administrative console, 35 alarm connector, 56 D C E cable lengths, 59 cable management arm CMA-800, installing, 26 CMA-Lite, installing, 25 installing, 24 command password, 44 pkgadd, 48 poweroff, 43 poweron, 42 setdate, 44 setupnetwork, 45 shutdown, 43 connecting administrative console, 36 initially, 35 I/O assemblies, 37 power cables, 33 system controller, 34 connection alarm, 56 Ethernet, 57 LOM Ethernet, 58 serial, 59 SCSI, 55 Ethernet cable len
bottom position, 9, 11 inner, 6 lock nuts, 22 Sun Fire or StorEdge cabinet, 9 Sun Rack 900 cabinet, 11, 13 top position, 10, 13 Solaris, 46 L LOM adapter DB-25, 61 DB-9, 61 connection Ethernet, 58 serial, 59 N network parameters configuring, 45 O On/Standby switch, 40, 41 disabling, 41 powering on, 41 standby mode, 43 P password command, 44 PCI+ IB_SSC conditions, 54 pkgadd command, 48 powering on, 41 LOM command, 42 On/Standby switch, 41 poweroff command, 43 poweron command, 42 preparing installing ser