Server User Manual
Table Of Contents
- Sun Fire™ X2250 Server Service Manual
- Contents
- Preface
- Sun Fire X2250 Server Overview
- Troubleshooting
- Performing Diagnostics
- 3.1 Pc-Check Diagnostics Overview
- 3.2 System Information Menu Options
- 3.3 Advanced Diagnostics Tests Menu Options
- 3.4 Immediate Burn-in Testing
- 3.5 Deferred Burn-in Testing
- 3.6 Create Diagnostic Partition Option
- 3.6.1 Removing Existing Partitions From a Hard Disk
- 3.6.2 Adding a Diagnostic Partition to the First Bootable Disk
- 3.6.3 Creating a Log File on the Diagnostic Partition
- 3.6.4 Accessing the Diagnostic Partition on a Red Hat Linux System
- 3.6.5 Accessing the Diagnostic Partition on the Solaris 10 Operating System
- 3.6.6 Accessing the Diagnostic Partition on the Windows Server 2003 Operating System
- 3.7 Show Results Summary
- 3.8 Print Results Report
- 3.9 About Pc-Check
- 3.10 Exit to DOS
- Maintaining the Sun Fire X2250 Server
- 4.1 Tools and Supplies Needed
- 4.2 Installation Precautions
- 4.3 Powering Off the Server and Removing the Cover
- 4.4 Locations of Server Components
- 4.5 Component Replacement Procedures
- 4.5.1 Replacing the I/O Board
- 4.5.2 Replacing the PCIe Card and Riser Assembly
- 4.5.3 Replacing a Hard Disk Drive and Carrier
- 4.5.4 Replacing an HDD Backplane Assembly
- 4.5.5 Removing and Installing the ODD Drive Assembly
- 4.5.6 Replacing the Air Duct
- 4.5.7 Replacing the Power Supply
- 4.5.8 Replacing the Single Fan Module
- 4.5.9 Replacing the Dual Blower Module
- 4.5.10 Replacing Memory Modules
- 4.5.11 Replacing the System Battery
- 4.5.12 Replacing a CPU and Heatsink
- 4.5.13 Installing a New CPU
- 4.5.14 Replacing Cables
- 4.5.15 Motherboard
- System Specifications
- Using the Tools & Drivers CD
- Installing the Server Into a Rack With Optional Slide Rails
- C.1 Disassembling the Slide Rails Before Installation
- C.2 Installing the Mounting Brackets Onto the Server
- C.3 Attaching the Slide-Rail Assemblies to the Rack
- C.4 Installing the Server Into the Slide-Rail Assemblies
- C.5 Installing the Cable Management Assembly
- C.6 Verifying Operation of the Slide Rails and CMA
- Index
Appendix B Using the Tools & Drivers CD B-11
B.5 Intel PROSET Driver Software
Included on the Tools & Drivers CD is a driver software package for the Intel
network interface card (NIC). After installing the Windows Server 2003 OS on the
X2250 server, you must install the NIC driver software.
If auto insert notification is enabled (default in Windows 2003), the NIC driver
software package is automatically installed on your server when the CD is inserted
into the DVD-ROM drive. If you need to reinstall or update the NIC driver software,
perform the following procedures.
B.5.1 Installing the Intel PROSET Driver Software
1. Insert the Tools & Drivers CD into the server DVD-ROM drive.
The system device driver autorun program automatically launches the X2250 Tools
& Drivers wizard.
2. In the X2250 Tools & Drivers wizard, select Install and Update System Device
Drivers.
The Intel NIC drivers are automatically installed on the server.
B.6 Updating FRU PROM When the System
Mainboard is Replaced
When a system is built at the factory, the system serial number (SSN) and ordered
product part number (PPN) are entered into the mainboard FRU PROM before the
unit ships. When a mainboard is replaced in the field, the new board will not contain
the SSN and PPN. As a result, ILOM will incorrectly display system FRU
information.
SSN and PPN values must be transferred into the replacement mainboard before
ILOM will correctly display any system FRU information. The procedure to transfer
SSN and PPN values into the replacement mainboard is as follows.
1. Locate the System Serial Number (SSN) on the front chassis label (or from
either ILOM or sdfru -l before the mainboard is replaced).