Server User Manual
Table Of Contents
- Sun Fire™ X2250 Server Service Manual
- Contents
- Preface
- Sun Fire X2250 Server Overview
- Troubleshooting
- Performing Diagnostics
- 3.1 Pc-Check Diagnostics Overview
- 3.2 System Information Menu Options
- 3.3 Advanced Diagnostics Tests Menu Options
- 3.4 Immediate Burn-in Testing
- 3.5 Deferred Burn-in Testing
- 3.6 Create Diagnostic Partition Option
- 3.6.1 Removing Existing Partitions From a Hard Disk
- 3.6.2 Adding a Diagnostic Partition to the First Bootable Disk
- 3.6.3 Creating a Log File on the Diagnostic Partition
- 3.6.4 Accessing the Diagnostic Partition on a Red Hat Linux System
- 3.6.5 Accessing the Diagnostic Partition on the Solaris 10 Operating System
- 3.6.6 Accessing the Diagnostic Partition on the Windows Server 2003 Operating System
- 3.7 Show Results Summary
- 3.8 Print Results Report
- 3.9 About Pc-Check
- 3.10 Exit to DOS
- Maintaining the Sun Fire X2250 Server
- 4.1 Tools and Supplies Needed
- 4.2 Installation Precautions
- 4.3 Powering Off the Server and Removing the Cover
- 4.4 Locations of Server Components
- 4.5 Component Replacement Procedures
- 4.5.1 Replacing the I/O Board
- 4.5.2 Replacing the PCIe Card and Riser Assembly
- 4.5.3 Replacing a Hard Disk Drive and Carrier
- 4.5.4 Replacing an HDD Backplane Assembly
- 4.5.5 Removing and Installing the ODD Drive Assembly
- 4.5.6 Replacing the Air Duct
- 4.5.7 Replacing the Power Supply
- 4.5.8 Replacing the Single Fan Module
- 4.5.9 Replacing the Dual Blower Module
- 4.5.10 Replacing Memory Modules
- 4.5.11 Replacing the System Battery
- 4.5.12 Replacing a CPU and Heatsink
- 4.5.13 Installing a New CPU
- 4.5.14 Replacing Cables
- 4.5.15 Motherboard
- System Specifications
- Using the Tools & Drivers CD
- Installing the Server Into a Rack With Optional Slide Rails
- C.1 Disassembling the Slide Rails Before Installation
- C.2 Installing the Mounting Brackets Onto the Server
- C.3 Attaching the Slide-Rail Assemblies to the Rack
- C.4 Installing the Server Into the Slide-Rail Assemblies
- C.5 Installing the Cable Management Assembly
- C.6 Verifying Operation of the Slide Rails and CMA
- Index
Contents vii
A.4 Serial Connector Pin Assignments A–4
B. Using the Tools & Drivers CD B–1
B.1 Tools & Drivers CD Contents B–1
B.2 Updating BIOS B–2
B.2.1 Updating Sun Fire X2250 BIOS Using the DVD Drive B–2
B.2.2 Updating Sun Fire X2250 BIOS From a Remote Client B–3
B.3 Updating SP Firmware B–4
B.3.1 ILOM CLI B–4
B.3.1.1 Updating ILOM SP Firmware Using the CLI B–4
B.3.2 ILOM Web Interface B–5
B.3.2.1 Updating SP Firmware B–5
B.4 Booting the Tools & Drivers CD From a PXE Server B–7
B.4.1 Setting up the Tools & Drivers CD Image on the PXE Server B–7
B.4.1.1 Setting Up the PXE Server B–7
B.4.2 Accessing the Tools & Drivers CD From the Target Sun Fire X2250
Server B–10
B.4.2.1 Accessing the Tools & Drivers CD From the Target
Server B–10
B.5 Intel PROSET Driver Software B–11
B.5.1 Installing the Intel PROSET Driver Software B–11
B.6 Updating FRU PROM When the System Mainboard is Replaced B–11
C. Installing the Server Into a Rack With Optional Slide Rails C–1
C.1 Disassembling the Slide Rails Before Installation C–2
C.2 Installing the Mounting Brackets Onto the Server C–3
C.3 Attaching the Slide-Rail Assemblies to the Rack C–4
C.4 Installing the Server Into the Slide-Rail Assemblies C–7
C.5 Installing the Cable Management Assembly C–9
C.6 Verifying Operation of the Slide Rails and CMA C–16