2019/08 Version 4.1 Dedicated PTZ Camera Professional SUNBA® PTZ Camera Analog Series User Manual Version 4.1 Visit http://analog.sunba.net to access the step by step YouTube video tutorials for setting up Sunba Analog PTZ camera.
FCC Warning (U.S.A) The device has been tested in compliance with limits set by Part 15 of Federal Communication Commission (Class B). The operation of the device is thus limited by the following two conditions: 1) it is not permitted to cause harmful interference to any authorized radio communications, and 2) it must accept any interference it receives. WARNING: Please test the camera locally by directly connecting to the default power adapter from the package before mounting it outside.
Common RS485 Control Type A: Digital Video Recorder (DVR) with RS485 Port A B RS485 Type B: 3D Pan Tilt Zoom Joystick (usually used with DVR without RS485 port or with CCTV monitor) Keyboard This enables your camera to pan tilt zoom. Incompatible DVR will result in problems such as B/W display, no video or the loss of PTZ control. 2.
Indoor Bench Test When you first receive the PTZ camera, please make sure it works properly before mount the camera outside. Note PTZ dome cameras have higher power requirements than bullet cameras and corresponding IP cameras. Therefore, how the unit is powered can be critical to its functionality. Please make sure the unit itself is working, and try eliminating all cabling factors to set up the bench test. How to Test Locally In short, in a bench test, do NOT extend the power line.
Stage2:Permanent Installation With DVR Power Video DC12V BNC PTZ Control Blue side goes to polar A on the RS485 port of the DVR Orange side goes to polar B on the RS485 port of the DVR Twisted Pair Cable With CCTV Monitor and 3D Pan Tilt Zoom Joystick Power Video DC12V CCTV Monitor BNC 3D Keyboard Blue side goes to polar + on the RS485 port of the 3D Keyboard Orange side goes to polar - on the RS485 port of the 3D Keyboard DC 9V A B + - PTZ Control 1.RS485A 2.RS485B 3.RS485+ 4.
3.Mount Installation for 305-A4X Step 1.
4.Cable Extension Methods 1)AC cable: Make sure your AC power source is close enough to the camera. The easiest way is to get a premade AC extension cable (no distance limit). Power strip is an example. 2)DC cable: Make sure the wire is AWG18 or thicker (distance dependent). The thicker the cable, the smaller the electrical resistance and the longer it can run without voltage loss. WARNING: Please strictly follow any applicable local security camera installation rules.
What is the PTZ address bit? Address bit is the unique ID (virtual) for PTZ analog cameras so that the terminal controller (DVR/Joystick) can recognize each camera connected to it. Address1 Camera1 Address2 Camera2 Address3 Camera3 Address4 Camera4 All 4 cameras have different addresses. They are easily recognizable! DVR The default address of Sunba PTZ camera is 1. So if you buy 2 PTZ cameras without changing the address on the 2nd unit, then…..
How to modify the PTZ address of the camera? Please set the camera’s address before using this dome. No same address (or ID) is allowed for more than one PTZ camera. By default, the address of PTZ camera is 1. Step 1: Go to the OSD Menu of the camera by calling preset 95+CALL (refer to the manual of your DVR if you want to learn how to use/call preset). See Chapter 5 for details of calling preset. Step 2: The first item in the OSD menu is the address bit.
PTZ Device RS485 Device Please change the address number that you just modified for the corresponding channel here. Channel 1 Protocol Pelco D None Address 1 1 Baud Rate 9600 9600 Data Bits 8 8 Stop Bits 1 1 None None Parity Important: If two cameras are both at the same address bit 1, you need to power one of the units off in order to modify the PTZ address bit of the other. How to double check the current PTZ address of the camera? Please reboot the device.
Special Presets Special presets are preset numbers not associated with positions but to advanced commands that cameras can follow to modify/enable settings such as setting up special auto scan boundaries etc. You can call the preset directly (no need to “add” a special preset as they are pre-existed) accor-ding to The Full Preset List. What does XX + CALL Mean? Example for 95+CALL below: Every PTZ supported DVR has a built-in PTZ control panel on the screen.
The Full Preset List Special Preset Function 0~50 Preset Conventional Position Preset XXX + Add Preset Set preset XXX. XXX + CALL Call preset XXX.
7.Camera OSD Menu Model: 305-A4X, 301-3X,301-AHD3X, 604-22X, When you open the OSD menu with preset 95+CALL, use the up and down keys to move the cursor, left key to go back to the previous menu, right key to select and confirm. Preset 95 + call will appear the following menu: MAIN MENU PAGE 2 MAIN MENU PAGE 1 SOFT ADDR PARK ACT NONE PARK TIME 15 FRAME SPEED 16 DWELL TIME LED MODE RESET 1 EXIT 8 AUTO LED ON 210 LED OFF 185 CAMERA Description of each option from the menu: 1.
3.PARK TIME The waiting time (or idle time) before the camera executes its PARK ACTION (see below). The default is 15 seconds. 4.FRAME SPEED The rate the dome scans continuously between two preset points. Valid value 1~31. Please read the “The Full Preset List” to learn how to set left and right scan boundary. 5.LED MODE A. AUTO MODE: Turn on and off IR LED automatically according to the value of photoresister.
8.Troubleshooting Built-in Self Test When powered up, the speed dome will automatically begin a self -diagnostic process during which the camera will pan horizontally and vertically to make sure PTZ, lens and other parts of the camera are functional. Please contact our technical staff if a self-test does not happen on your unit. Please refrain from disassembling the unit before contacting us. Symptom PTZ not working properly B/W display Red lights on but no power Reason & Solution 1.
Warranty Statement 1.This product comes with a 2-year limited US warranty covering parts only (1-Yr in other regions). You must pay the labor fee for repair inside the warehouse. However, any parts replacements are always covered and we will be sending you videos & instructions on how to fix the unit. Please contact us first within the warranty period to make sure the condition of warranty is met. 2.
