User's Manual

WARNINGS AND SAFEGUARDS
THERAPEUTIC LOW HEAT
Unlike traditional heating pads, your Renue™ Back & Body Warming Pad is designed
to provide a low-level therapeutic heat over an extended period of time. When used
as intended – on a chair or on a bed – it will give off consistent and soothing low
heat, providing therapeutic relief from aches and pains. The heat this pad generates
can best be experienced by seating or lying on top of the product.
SET-UP & USAGE INSTRUCTIONS
Your Renue™ Back & Body Warming Pad is designed to be
used on a chair or on bed for a continuous heat therapy. It
provides relief from aches and pains by giving off consistent
low level, soothing heat while you work or relax. This pad
can also be used as a proactive heat therapy – to reduce
stress and tension before it hurts!
FOR USE ON A CHAIR:
1. Place the Renue™ Back & Body Pad on a chair, with
softer fleece fabric facing out. The cord connector
should be on the right side of the chair's seat, and the
two loop holes for straps should be at the top corners
of the chair’s back (Figure 1).
2. Secure the pad on the chair with provided flexible
Velcro straps (Figures 2a-b). Depending on personal
preference and the size and type of chair, the
orientation of the straps may change. Place the straps
in a way that allows the pad to be attached securely to
the chair while still being comfortable to sit on.
3. As an optional feature, your Renue™ Back & Body
pad can be rolled up for lumbar support, allowing for
added comfort throughout the day. Just roll up the
seat portion of the pad and secure with the Velcro
strip on the underside of the pad (Figure 3).
4. Make sure Control Connector is securely attached to
the Pad Connector (Figure 4). Push both parts together
until they click for a tight fit.
NOTE: Control must be connected to heating pad
before plugging unit into outlet.
5. After control is connected to pad, plug into 120V AC
electrical outlet. For convenience, the pad features a
snap that can be used to keep cord & controller handy,
but out of the way (Figure 5).
NOTE: To avoid any tangling or pinching, do not tuck in
the cord between chair’s seat and back or arms.
6. To turn the pad on, press the Power Button. Then
select from 4 heat settings by scrolling to the desired
setting with the Power Button from "warm" to "high"
(Figure 6).
7. To turn the pad OFF, scroll through the remaining heat
settings by pressing the Power Button sequentially
until no lights remain lit.
AUTO-OFF FEATURE
Your pad controller includes an Auto-Off feature. This feature is designed to conserve
energy by automatically turning off after 8 hours of continuous use.
NOTE: After a power outage, the Auto-Off feature automatically resets the timer.
CARE AND CLEANING
BEFORE WASHING OR STORING YOUR HEATED PRODUCT:
1. Disconnect power cord from wall BEFORE detaching control cord from the
heated product.
2. Ensure that no cords are still connected to the pad and none of the wires have
worn through the fabric of the pad.
3. Carefully follow all washing instructions or your Renue™ Back & Body pad
may shrink and/or cause a fire hazard.
•DO NOT submerge control in water.
•DO NOT dry clean your heated product. Dry cleaning solvents may damage the wires.
•DO NOT use bleach or cleaning fluids.
•DO NOT use a wringer.
•DO NOT iron your heated product.
•DO NOT use mothballs or sprays of any kind.
•DO NOT reconnect the heated product or use it until it is COMPLETELY dry.
•DO NOT wash or put into water the power cord or any of the product’s cords.
Taking care of your Renue™ Back & Body Pad is easy as long as you follow a few
simple steps.
MACHINE WASHING
1. Presoak the pad for 15 minutes in mild soap and lukewarm water.
2. Wash in mild soap and lukewarm water on the “delicate” or “gentle” cycle in
the washer for two minutes. Remember, do not use bleach.
3. Rinse in fresh, lukewarm water.
4. Spin dry in the washing machine. Then gently stretch to its original size.
MACHINE DRYING
CAUTION: Do not use commercial dryers or the dryers at your local laundromat. They
get too hot and will damage the wiring of the heated product.
1. Preheat the dryer on the “low” temperature setting for 2 minutes.
2. Place pad into the dryer. Remove the pad while it is still damp, then gently
stretch pad to its original size.
3. Drape pad over a clothesline or a shower rod. DO NOT use clothespins.
4. Pad must be COMPLETELY dry before reconnecting the power plug or control
plug.
HAND WASHING
1. Presoak the pad for 15 minutes in mild soap and lukewarm water.
2. Gently squeeze the soap suds through a few times.
3. Rinse in fresh, lukewarm water.
HAND DRYING
1. Gently stretch the pad back to its original size.
2. Drape over a clothesline or hang over a shower rod. DO NOT use clothespins.
3.
Pad must be COMPLETELY dry before reconnecting the power plug or control plug.
www.sunbeam.com
5-YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada)
Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of five years from the
date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace
this product or any component of the product found to be defective during the warranty period. Replacement will be made
with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a
similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or
mechanical functions on this product. Doing so will void this warranty. This warranty is valid for the original retail purchaser
from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to
obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter,
modify or any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use
contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service
center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory
warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability
or fitness for a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be
liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including
incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or
otherwise, or for any claim brought against purchaser by any other party. Some provinces, states or jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so
the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights that vary from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A. - If you have any question regarding this warranty or would like to obtain warranty service, please call 1-800-435-1250
and a convenient service center address will be provided to you.
In Canada - If you have any question regarding this warranty or would like to obtain warranty service, please call 1-800-667-8623
and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in
Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as
Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or
claim in connection with this product, please write our Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
©2012 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Distributed by Sunbeam
Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
Printed in China. DW-080112 PN: 156796
THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS
PLUG IS INTENDED TO FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE
PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
Renue
™
Back & Body Pad
Model: 889
IMPORTANT SAFETY INSTRUCTIONS – DO NOT DESTROY
FOR USE ON A BED:
1. The Renue™ Back & Body pad can be placed on top
of or underneath a fitted sheet.
2. Place the pad on a bed in the position that best allows
heat to target the affected area of aches or pains.
The softer fleece fabric should be facing up (Figure 7).
3. Make sure Control Connector is securely attached to
the Pad Connector (Figure 4). Push both parts together
until they click for a tight fit.
NOTE: Control must be connected to heating pad
before plugging unit into outlet.
4. After control is connected to pad, plug into 120V AC
electrical outlet.
5. Run the control cord on the floor under the bed.
To avoid any tangling or pinching, do not sandwich
cord between the mattress and box spring. For your
convenience, the pad features a snap that can be used
to keep the cord & controller handy, but out of the way.
6. To turn the pad on, press the Power Button. Then
select from 4 heat settings by scrolling to the desired
setting with the Power Button from "warm" to "high"
(Figure 6).
7. To turn the pad OFF, scroll through the remaining heat
settings by pressing the Power Button sequentially
until no lights remain lit.
AS WITH ALL ELECTRICAL PRODUCTS, MISUSE OF PRODUCT
OR FAILURE TO PROPERLY FOLLOW THE INSTRUCTIONS MAY
CAUSE OVERHEATING, FIRE OR PERSONAL INJURY. PLEASE
READ THE PRODUCT LABEL AND ALL OF THE INSTRUCTIONS
BEFORE USING YOUR HEATED PRODUCT.
1. DO NOT USE THIS HEATED PRODUCT WITH AN INFANT,
A CHILD, AN INCAPACITATED OR IMMOBILE PERSON,
A PARAPLEGIC, A QUADRIPLEGIC, A DIABETIC, ONE
INSENSITIVE TO HEAT SUCH AS A PERSON WITH POOR
BLOOD CIRCULATION, OR ANYONE WHO CANNOT CLEARLY
UNDERSTAND THE INSTRUCTIONS AND/OR OPERATE THE
CONTROLS.
2. WHEN USED ON A BED, DO NOT ROUTE ELECTRICAL
CORDS BETWEEN THE MATTRESS AND BOX SPRING. DO
NOT ALLOW THE CORDS TO BE PINCHED.
3. DO NOT USE WITH DAMAGED CORDS. DAMAGED CORDS
CAN LEAD TO FIRE. DO NOT TUCK IN, TRAP, FOLD, CROSS
OR PINCH CORDS BETWEEN CHAIR’S SEAT AND BACK
OR ARMS, AGAINST WALLS, BETWEEN BED SLATS,
MATTRESS OR SPRINGS, FOOTBOARDS OR BED FRAME.
4. DO NOT DRY CLEAN THIS HEATED PRODUCT. CLEANING
LIQUID AND BLEACH MAY DAMAGE THE INSULATION OF
THE HEATING ELEMENT. IMPROPER LAUNDERING MAY
CAUSE PROBLEMS WITH THE HEATING WIRE WHICH CAN
LEAD TO FIRE.
5. DO NOT TUCK IN, PINCH, FLEX OR EXPOSE THE HEATING
WIRE TO RUBBING. A DAMAGED HEATING WIRE MAY
RESULT IN POSSIBLE OVERHEATING OR FIRE. DO NOT
TUCK THE HEATED PRODUCT OR SUPPLY CORD IN A
SOFA, ARMCHAIR OR OTHER FURNITURE.
6. TURN OFF OR UNPLUG THE CONTROL FOR THE HEATED
PRODUCT WHEN NOT USING.
7. WRAPPING THE CORD AROUND THE CONTROLLER MAY
DAMAGE THE CORD. LOOP LOOSELY WHEN STORING.
8. CONTROLLER IS NOT WATERPROOF. DO NOT IMMERSE IN
WATER.
9. KEEP THE CONTROL AWAY FROM DRAFTY AREAS, SUCH
AS BY AN OPEN WINDOW, WHICH MAY CAUSE IT TO
BECOME DAMP OR WET.
10. DO NOT USE PINS; THEY MAY DAMAGE THE ELECTRIC
WIRING.
11. BE SURE THAT THIS HEATED PRODUCT IS USED ONLY ON
AN AC SUPPLY CURRENT CIRCUIT OF 110-120 VOLTS. DO
NOT USE WITH AN EXTENSION CORD.
12. THE PRODUCT MAY EXPERIENCE INCREASED HEAT
IN AREAS WHERE HEATED PRODUCT IS BUNCHED OR
FOLDED WHILE IN USE.
13. KEEP ALL DOGS, CATS AND OTHER PETS AWAY FROM
THIS HEATED PRODUCT. THIS IS AN ELECTRICAL
APPLIANCE THAT THEY CAN DAMAGE OR BE INJURED BY.
14. DO NOT USE THIS HEATED PRODUCT ON A WATERBED,
BUNK BED, MECHANICALLY ADJUSTABLE BED OR A
CHILD’S CRIB/BED.
15. DO NOT USE WITH ROCKING CHAIRS, RECLINERS, CHAIRS
WITH CASTERS OR WHEELS, OR OTHER FURNITURE
SUBJECT TO MOVEMENT. DO NOT WRAP PRODUCT
AROUND CONTROL.
16. DO NOT USE ANOTHER ELECTRONIC HEATING DEVICE IN
CONJUNCTION WITH YOUR HEATED PRODUCT.
17. IF THESE IMPORTANT INSTRUCTIONS ARE NOT
FOLLOWED, THE HEATED PRODUCT WILL NOT OPERATE
PROPERLY.
18. NOT FOR HOTEL, MOTEL OR OTHER INSTITUTIONAL USE.
19. DO NOT USE WITH GENERATOR POWER.
20. IF YOU SEE THE HEATED PRODUCT OPERATING
IMPROPERLY, UNPLUG IT IMMEDIATELY AND CALL
SUNBEAM CONSUMER CARE IN THE U.S AT 800-435-1250
OR IN CANADA AT 800-667-8623.
A. Control Connector
B. Pad Connector
A
B
Figure 1
Figure 2a
Figure 2b
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7