Includes QUICK SET-UP GUIDE pages 4-5 heated bedding U S E R M A N U A L TRUSTED FOR OVER 100 YEARS P.N.
IMPORTANT INSTRUCTIONS DO NOT DESTROY WARNINGS AND SAFEGUARDS AS WITH ALL ELECTRICAL PRODUCTS, MISUSE OF PRODUCT OR FAILURE TO PROPERLY FOLLOW THE INSTRUCTIONS MAY CAUSE OVERHEATING, FIRE OR PERSONAL INJURY. PLEASE READ THE PRODUCT LABEL AND ALL OF THE INSTRUCTIONS BEFORE USING YOUR HEATED PRODUCT. 1.
11. CONTROLLER IS NOT WATERPROOF. DO NOT IMMERSE IN WATER. 12. KEEP THE CONTROL AWAY FROM DRAFTY AREAS THAT MAY BECOME DAMP OR WET SUCH AS AN OPEN WINDOW. 13. DO NOT USE PINS; THEY MAY DAMAGE THE ELECTRIC WIRING. 14. BE SURE THIS BLANKET/MATTRESS PAD/THROW IS USED ONLY ON AN AC SUPPLY CURRENT CIRCUIT OF 110-120 VOLTS 60 HZ. DO NOT USE WITH AN EXTENSION CORD. DO NOT USE WITH GENERATORS, POWER CONVERTERS, OR INVERTERS. 15.
QUICK SET-UP GUIDE Mattress Pad & Blanket STEP 4 TWIN/FULL SINGLE CONTROL SET-UP STEP 1 Place on bed with label at foot of bed facing out Plug Power Cord into wall Power Cord Left Side Control Right Side STEP 2 Connect the Control Cord connector and module securely Module Label Control Cord Connector STEP 3 Run Control Cord under the bed Flag Tag BASE UNIT FOR REMOTE CONTROL SET-UP 4 1 Module 2 3 Run Base Unit Cord under the bed QUEEN/KING/CALIFORNIA KING DUAL CONTROL SET-UP STEP STEP
QUICK SET-UP GUIDE Heated Throw STEP STEP 1 2 Flag Tag Connect the Control Cord connector and module securely Control Plug Power Cord into wall Power Cord Module Flag Tag Throw Cord Connector Label Throw Cord Control Control Cord Control Cord Connector Connector Power Cord Module Throw Cord Connector Label Throw Cord PLEASE follow these directions in the order they are given to ensure your product will work correctly. Do not turn on the product until it has been fully assembled.
Table of Contents Quick Set-Up Guide................................................................................................. 4-5 Heated Blanket, Mattress Pad and Comforter Setup...................................................................................................................... 7 Controllers........................................................................................................ 8-10 Heated Throw Setup............................................................
Heated Blanket, Mattress Pad and Comforter Setup 1 Place the heated blanket/mattress pad on the bed with the label at the foot of the bed facing upward. 2 Connect the cord into the module at the bottom of the heated blanket/ mattress pad until the plastic hinges click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of fire could result from a loose connection. 3 Run the control cord on the floor under the bed. Do not sandwich cord between the mattress and box spring.
Control Chart OneSet™ SimpliTouch™ EasySet™ Pro StyleSmart™ II ComfortSet™ SelectTouch™ ChoicePlus™ DesignSmart™ ChoiceTouch™ EliteStyle™ PrimeStyle™ EliteStyle™ II SimpliTouch™ Pro AO Style # (Single Control) Y85 K85P S85/S85A U85/U85A 085 P85/ P85A 85P W85/ W85A X85/X85A Style # (Dual Control) Y85KQ K85KQP S85KQ/ S85KQA P85KQ/ P85KQA 85KQP W85KQ/ W85KQA X85KQ/ X85KQA U85KQ/ U85KQA Backlit Display 085KQ b LED Display Warming Settings b b b b b 10 hour 10 hour 10 hour* (S85A,
Preheat Feature (selected models only): The preheat function will heat the bed for a period of 30 minutes and the control will return to its original setting. 1 To use the preheat feature, simply turn on the warming product by pressing the “On/Off” button and then press the “Preheat” button. The display will show “PH” while the function is activated. 2 To reset the preheat feature, simply turn off the control by pressing the “On/Off” button and then turn it back on by pressing the “On/Off” button.
Note: there is a P to the right of the clock to denote PM. 4. Release the button to stop at the desired time. 5. When the desired time has been reached, slide the switch to the center position to save the time and return to normal operation. Note: The clock will blink until the time has been set. The control will remember the time settings unless AC power is disconnected. Selectable Auto Off: You can set the auto-off time at 2hrs, 6hrs or 10hrs.
Note: When the Preheat Mode is set to turn on at the set time, the clock display will show the time the blanket will begin the preheat, not the actual time of day. This is to remind you when you have the blanket set to start preheat. Heat Adjustment: There are 10 Heat level settings from Low to Hi. To adjust the heat setting, simply press the + (raise heat temp) or the – ( lower heat temp) on the large circular button in the center of the control. Dimmer: You can adjust the brightness of the display.
Care and Cleaning OF YOUR HEATED BEDDING PRODUCT We recommend washing before initial use. Before Washing or Storing Your Heated Bedding Product: 1 Disconnect power cord from wall BEFORE detaching control cord from the heated product. 2 Ensure that no cords are still connected and none of the wires have worn through the fabric. 3 Carefully follow all washing instructions or your heated product may shrink and possibly cause a fire hazard. • DO NOT submerge control in water.
Frequently Asked Questions ABOUT YOUR HEATED BEDDING PRODUCT Q Who should NOT use the heated blanket, heated mattress pad or heated throw? A The following people should NOT use the heated blanket, heated mattress pad or warming throw: • An infant • A child • An incapacitated or immobile person • A paraplegic • A quadriplegic • A diabetic • Anyone insensitive to heat such as a person with poor blood circulation • Anyone who cannot clearly understand the instructions and/or operate the controls Q What
Q What does “F” ,“FF”, “F1” or “F2” mean on my Electronic Digital Control? A T he digital controls are designed to notify you in the event that a problem has been discovered by flashing “FF”, “F1” or “F2” on the display. Models: ChoicePlus™ Follow instructions below. FF F1 Models: SelectTouch™, ComfortSet™ Follow instructions below. F2 Models: SelectTouch™, ComfortSet™ Follow instructions below. F Models: StyleSmart™ II, DesignSmart™, ChoiceTouch™ Follow instructions below. 1.
PLEASE DO NOT RETURN THIS PRODUCT TO PLACE OF PURCHASE. Limited Warranty Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period stated below from the date of purchase, this product will be free from defects in material and workmanship. • All heated products branded “Arlington™” will carry a ONE year limited warranty.
PLEASE DO NOT RETURN THIS PRODUCT TO PLACE OF PURCHASE We’re Here to Help, Please contact Jarden Consumer Care Centers listed below: How to Obtain Warranty Service In the U.S.A. If you have any question regarding your heated product, this warranty or would like to obtain warranty service, please visit our web site at: www.sunbeam.com or contact Jarden Consumer Care at 1-800-892-7684 and a convenient service center address will be provided to you.