Compact Ceramic Oscillating Heater 1800W oscillating heater with ceramic element Instruction Booklet HE2105 Please read these instructions carefully and retain for future reference.
Contents Sunbeam’s Safety Precautions 1 Sunbeam’s Safety Precautions for your Heater 2 Sunbeam’s Total Safety System 3 Features of your Compact Oscillating Ceramic Heater 4 Using your Compact Oscillating Ceramic Heater 6 Using the Oscillation function 7 Resetting the Total Safety System 7 Troubleshooting Guide 8 Care and Cleaning 8
Sunbeam’s Safety Precautions • • • • • • • • • Sunbeam is very safety conscious when designing and manufacturing consumer products, but it is essential that the product user also exercise care when using an electrical appliance. Listed below are precautions which are essential for the safe use of an electrical appliance: Read carefully and save all the instructions provided with an appliance. Always turn the power off at the power outlet before you insert or remove a plug.
Sunbeam’s Safety Precautions • Do not locate the heater immediately below a • This heater becomes hot during use. To avoid socket outlet. burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this • Do not use this heater in the immediate heater. Keep combustible materials such as surrounds of a bath, shower, laundry area or furniture, pillows, bedding, papers, clothes and swimming pool.
Sunbeam’s Total Safety System Safety auto shut off Your Sunbeam Compact Oscillating Ceramic heater is equipped with a safety system that detects any abnormally high temperatures within the heater and automatically shuts it off to prevent overheating. If the heater is getting excessively hot, an alarm will sound. Instant tip over cut out The instant tip over cut out interrupts the power to the heating element and fan if the heater is accidentally tipped over.
Features of your Compact Oscillating Ceramic Heater Mode button Press the mode button to select the desired operating mode: low heat, high heat auto, fan or standby Fan setting Ideal for circulating cool air in summer, the fan setting operates the fan without heat. Power ON light Illuminates to indicate that the heater is connected to the power outlet. LCD screen The LCD screen displays the current settings including the ambient room temperature, the selected mode, or heat setting.
O Oscillation function The heater oscillates 90 degrees to provide greater heat distribution. Simply press the oscillation button (OSC) to activate this function. Electronic thermostat The electronic thermostat allows for precise temperature control. Select the auto mode to set the electronic thermostat and turn the thermostat dial to the desired heat setting. Once your desired temperature is reached, the heater will cycle on and off to maintain it.
Using your Compact Oscillating Ceramic Heater 1. Place the heater on a flat level surface and ensure that the air intake and outlet are clear of obstructions. 2. Insert the plug into a 230/240V power outlet and turn the power on. 3.The power on light and LCD screen will illuminate. Note: When the heater is switched on it will be automatically set to the Standby mode. 4. Press the mode button to select the desired setting, as follows.
Using the Oscillation Function The 90 degree oscillation function can be used in any mode except standby. 1. Press the oscillation button (OSC), positioned on the top of the heater. The heater will then begin to oscillate from side to side. 2. To stop the heater from oscillating, simply press the oscillation button (OSC) once again.
Troubleshooting Guide • Make sure the electrical outlet or circuit breaker is working. • Check that the thermostat is not set too low. Turn the thermostat dial clockwise to adjust the electronic thermostat until the heater restarts. • Check for obstructions. If you find an obstruction, turn the heater off and follow the reset instructions on page 7. • The safety auto shut-off may have activated, so follow the instructions for resetting on page 7.
2 Year Replacement Guarantee In the unlikely event that this appliance develops any malfunction within 2 years of purchase (3 months commercial use) due to faulty materials or manufacture, we will replace it for you free of charge. Should you experience any difficulties with your appliance, please phone our customer service line for advice on 1300 881 861 in Australia, or 0800 786 232 in New Zealand. Alternatively, you can send a written claim to Sunbeam at the address listed below.
Need help with your appliance? Contact our customer service team or visit our website for information and tips on getting the most from your appliance. In Australia Visit www.sunbeam.com.au Or call 1300 881 861 In New Zealand Visit www.sunbeam.co.nz Or call 0800 786 232 is a registered trademark. Made in China. Due to minor changes in design or otherwise, the product may differ from the one shown in this leaflet. © Copyright. Sunbeam Corporation Limited 2006.
