purifying fountain Model SBCF01 INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS • This device should only be used when training dogs for deterring unwanted behaviors. • This device is not a toy; keep out of reach of children. • This device is not intended to provide protection against aggressive dogs. • This basic remote trainer should only be used on one dog at a time. • Your dog should be in good health when using this product. • This product is not to be used on dogs less than 9 lbs. • This product is not to be used on dogs less than 6 months old.
Product Overview: Collar INDICATOR LIGHTS: • Low • Med • High Solid Green: Correction level selected and functioning properly MAIN CONTROL BUTTON: • On/Off • Correction level adjustment • System reset Flashing Green: Correction administered and received All 3 Flashing Red: Low battery STAINLESS STEEL PROBES: Correction administering system CHARGING JACK FABRIC COLLAR QUICK RELEASE CLASP 2 ADJUSTABLE BUCKLE
Product Overview: Remote Control INDICATOR LIGHTS: TRANSMIT INDICATOR LIGHTS: POWER Flashing Green: The warning or correction has been transmitted effectively Flashing Red: Over Correction Mode Solid Green: Remote is on Flashing Red: Low battery • Correction button • On/Off • Warning tone button CHARGING ADAPTER: • 2 ft.
How it Works: The Sunbeam® Rechargeable Remote Trainer should be used as a training aid for you and your pet. This specially designed system will shut off if there is an excess of corrections, for example, if something is leaning on the correction button or if there is continuous pressing. This is called Over Correction Mode and will cause the unit to turn off and automatically reset. IMPORTANT: The Sunbeam® Rechargeable Remote Trainer has a range of up to 400 yards.
Charge the Remote Control • Locate the charging jack on the Remote Control and lift the rubber cover. (fig. 4) • Insert one of the charger connectors into the charging jack. (fig. 5) figure 4 • Plug the charger into a standard wall outlet. • While the Remote Control battery is charging: - If the Remote Control is turned off, the LED lights will flash red and green indicating the battery is charging. The LED lights will flash green indicating when it is fully charged.
Use the longer stainless steel probes if the coat does not allow the shorter probes to reach the skin. Before changing the stainless steel probes you must completely discharge the collar by holding a plastic handle screwdriver across both stainless steel probes for 5 seconds. Make sure the metal portion of the screwdriver is touching both stainless steel probes and the unit is in the OFF position.
The default correction level is LOW; this setting will illuminate green for 10 seconds and then turn off. During the ten seconds, you may toggle to different correction levels by pressing the Main Control Button. STEP 2: Set correction level by pressing and holding (approximately 2 seconds) the Main Control Button until a green LED illuminates at the desired setting. When a green LED is illuminated press the Main Control Button once to toggle to the next correction level.
SPECIAL OPERATING NOTES REMOTE CONTROL: For precaution, the collar will be ready to use 10 seconds after the user has selected or made adjustments to the correction level on the collar. The collar will not react to the handheld remote when the user turns the collar on and/or toggles the correction settings during this period. WARNING BUTTON: If the user presses the warning button on the remote control, the transmit green LED on the remote will flash. There will be an audible beep at the collar unit.
Each dog can have a different reaction to the correction it receives from the remote trainer. Reactions can vary from a dip of the head, to shaking the head, whining, excessive barking, confusion or running away. In the event of an extreme reaction or aggression, wait until your dog is calm before approaching your dog. The remote trainer should be used when you want to deter unwanted behavior. Do not leave the remote trainer collar on your dog when you are not present.
FCC STATEMENT Potential for Radio/Television Interference This device complies with part 15 and 95 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and 95 of the FCC Rules.
1 YEAR WARRANTY In the U.S.A. and Canada If you have any question regarding this warranty or would like to obtain warranty service, please call 1-866-537-2249 and a convenient service center address will be provided to you. Sunbeam® Products, Inc.