User Manual

Operating Instructions
FILLING WATER TANK
Warning: To avoid personal injury and
damage to the unit, only add water to
the water tank. NEVER add cleaning
solutions, perfumes, oils or any other
chemical additives.
Note: Your Steamer is designed to be
used with tap water. However, if you have
hard water, we recommend using distilled
water for better results.
1. Place Steamer on a at surface.
2. Hold the water tank with one hand
while turning the steamer handle
counterclockwise with other hand, until
the arrow on the handle reaches the
unlock symbol ( ) on the water tank.
Lift the handle off the water tank. Set
the Steamer aside (Figure 1).
3. Take the water tank to a sink. Pull the
rubberized water-ll cover to open and
pour tap water from the tap into the
water-ll opening until it reaches the
Max water level in water tank (Figure
2). If water spills outside of the tank,
or within the center water tank cavity,
wipe it dry with a paper towel or cloth.
Warning: When lling the water tank,
watch for water that can drip onto the
oor and cause you to slip and fall.
Tip: It is not necessary to have a
full tank of water for the Steamer to
generate steam. For best results, just
make sure the water tank is at least
half full.
4. Close the water-ll cover, insert the
handle into the water tank and turn
clockwise until the arrow on the handle
aligns with the lock symbol ( ) on the
tank. Pull on the handle to ensure it is
fully locked in position.
Note: If you need to add water while
steaming, unplug the steamer, wait
until it cools and follow above steps.
If a loud vibrating noise is heard, then
the water level is low and needs to be
relled.
ATTACHING AND REMOVING ACCESSORIES
• To attach: Grasp both sides of the
accessory and insert the heated press
bar opening at the top of the accessory,
behind the small tab above the heated
press bar then gently press accessory
onto steamer head until it snaps into
place.
• To remove: Grip accessory handle and
gently pull toward you to separate from
the steam head (Figure 3).
Door
Puerta
Figure 1
Door
Puerta
Figure 2
USING YOUR STEAMER VERTICALLY
You can use your Steamer in the vertical
position to press with steam hanging
garments and drapes.
Caution: Heated press bar gets hot. Do not
touch!
1. With the water tank lled, attach
desired accessory to use on your
garment (refer to ATTACHING AND
REMOVING ACCESSORIES).
2. Hang your garment to be steamed on
a clean, rust-free hanger.
3. Plug unit into a standard electrical
outlet.
Warning: Care should be taken to
arrange the cord so that it cannot be
pulled or tripped over. Always make
sure you can move freely without
getting tangled with the cord.
4. Slide the switch to Low or High. The
red power indicator light illuminates
and will cycle on and off as the
temperature is maintained, and in
just approximately 45 seconds, the
green ready light will also illuminate.
The green light may cycle off, and the
pump will stop if the temperature is
too low to generate steam.
Caution: Burns could occur from
touching hot metal parts, hot water,
or steam. Use care when you turn a
steam appliance upside down – there
may be hot water in the reservoir.
5. You are now ready to start steaming!
6. Hold your Steamer by the handle
in vertical position with the head
pointing toward the fabric and away
from you and your body.
Warning: Steam is hot. Always point
steamer exit away from yourself, other
persons, pets, plants and walls. Never
steam clothes while they are being
worn.
7. With your free hand, pull the fabric
tight and press the trigger switch as
you move the Steamer over the fabric.
Tip: If using the Creaser accessory,
press the lever to open it and just run
the edge of your fabric through it to
create an iron-like crease.
8. You can use the trigger two ways:
a. Press the switch to generate steam
and release it to pause the steam.
OR
b. To get continuous steam, you can
press the triggger switch and move
it down to the lock-down position.
9. Touch the fabric lightly with the heated
press bar, moving it in a downward
motion, beginning at the top of the
garment and moving downward.
Caution: The heated press bar gets
hot, do not touch.
10. Repeat this step until fabric is wrinkle
free.
Tip: For more difcult wrinkles, try
steaming from the underside of the
fabric.
11. When nished, move trigger switch
up to release it from the lock down
position and slide switch to Off.
12. Place Steamer on a at surface and
unplug from electrical outlet.
13. Wait until Steamer has cooled and
empty water tank.
Note: Always unplug the Steamer when
not in use.
Door
Puerta
Figure 3
Operating Instructions (continued)
7
6