Solus Digital Resilium ® Instruction Booklet SR7000 Please read these instructions carefully and retain for future reference.
Contents Sunbeam’s Safety Precautions 3 4 Features of your Solus® Digital Iron 6 Using your Solus® Digital Iron The Safety Auto-Off Feature 7 Care and Cleaning of your Solus® Digital Iron 8 Troubleshooting 8 Ironing Tips & Tricks 9 Ironing Chart 10 Important instructions – retain for future use.
Sunbeam’s Safety Precautions SAFETY PRECAUTIONS FOR YOUR IRON • Do not leave a hot iron within reach of children. If they come into contact with a hot iron it could lead to serious burns. • Iron only on an ironing board. • An iron takes approximately 30 minutes to cool down. Allow the iron to cool completely before storing. • Do not wind the cord around the soleplate while the iron is still hot. • Do not leave the iron unattended while it is plugged into the power outlet.
Features of your Sunbeam Ultura Iron Extreme shot of steam Squeezing the shot of steam trigger instantly produces a concentrated, high-pressure shot of steam to remove stubborn wrinkles. Vertical shot of steam Squeezing the shot of steam trigger with the iron in an upright position produces a vertical shot of steam, which is ideal for steaming curtains and suits, and removing creases from delicate fabrics.
CO Digital thermostat The digital thermostat provides precise temperature control, allowing you to select the exact temperature recommended for each garment. It eliminates temperature overshoot and minimises temperature fluctuations. This ensures consistently superior results and prevents scorching. Temperature alert The light located on the iron handle indicates when the iron soleplate has reached the selected temperature.
Using your Sunbeam Solus® Iron Before first use Remove any adhesive stickers, plastic covers or cardboard sleeves from the soleplate. Ensure that all adhesive is removed by rubbing the soleplate with a cloth dampened with methylated spirits. Fill the water tank and empty the water. This will rinse out any foreign particles remaining in the water tank from the manufacturing process. NOTE: When turned on for the first time, your new iron may give off vapours for up to 10 minutes.
Using your Sunbeam Solus® Iron (continued) Using the shot of steam The shot of steam can be used when dry or steam ironing, when the temperature is set above the two dot (••) setting. 1. Ensure the tank is at least 1/4 full of water. 2. Select the desired temperature and wait until the temperature alert light illuminates green. 3. Squeeze the shot of steam trigger several times with the iron on the soleplate to prime the pump.
Care and Cleaning After each use 1. Turn the power off and remove the plug from the power outlet. 2. Allow the iron to cool before winding the cord around the built-in cord wrap. Storage Always store the iron on its heel rest. Do not store the iron with the soleplate facing down, or in the carton. Cleaning To clean the exterior of your iron, wipe over with a damp soft cloth and wipe dry.
Ironing Tips and Tricks Tip # 27 - Iron shirts like a pro Start with the collar, working from the outer edges into the middle. Iron the shoulder next, followed by the cuffs and sleeves. Place the collar at the narrow end of the board so that one front panel of the shirt is extended flat. Iron the front panel from shoulder to shirt tail. Rotate to iron the back of the shirt. Rotate and complete the remaining front panel. Tip # 34 - Tips for T-shirts Straighten seams on t-shirts before hanging out to dry.
Ironing Chart Temperature Setting minimum MIN synthetic SYNTH silk SILK Fabric Ironing Recommendation Acrylic Dry iron on wrong side. Acetate Dry iron on wrong side while still damp or use spray to dampen. Nylon Iron on wrong side while still damp or use spray to dampen. Polyester & Rayon Iron on wrong side of fabric. Viscose Mainly dry iron. Steam can be used under manufacturer’s instructions. Silk Iron on wrong side. Use an ironing cloth to prevent shine marks.
2 Year Replacement Guarantee In the unlikely event that this appliance develops any malfunction within 2 years of purchase (3 months commercial use) due to faulty materials or manufacture, we will replace it for you free of charge. Should you experience any difficulties with your appliance, please phone our customer service line for advice on 1300 881 861 in Australia, or 0800 786 232 in New Zealand. Alternatively, you can send a written claim to Sunbeam at the address listed below.
Need help with your appliance? Contact our customer service team or visit our website for information and tips on getting the most from your appliance. In Australia Visit www.sunbeam.com.au Or call 1300 881 861 In New Zealand Visit www.sunbeam.co.nz Or call 0800 786 232 is a registered trademark. ‘Solus’ and ‘Resilium’ are registered trademarks of Sunbeam Corporation. Made in China. Due to minor changes in design or otherwise, the product may differ from the one shown in this leaflet. © Copyright.
