All-Weather Outdoor LCD Television Operator’s Manual Model SB-6560HD Rev.
Important Safety Instructions Dear SunBriteTV Customer: Congratulations on the ownership of Model 6560HD all-weather outdoor LCD TV, and welcome to the family of satisfied SunBrite customers. You are in great company with thousands of homeowners and esteemed commercial facilities such as Yankee Stadium, Fenway Park, Disney World, and Sea World who have trusted us to deliver superior performance, lasting durability and the enjoyment of superb television viewing in the great outdoors.
Cleaning Instructions: See “Care of SunBriteTV” on page 32 Attachments: Do not use attachments not specifically recommended by the manufacturer. Use of improper attachments can result in accidents. Power Source: SunBriteTV must operate on a power source indicated on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. When using the TV outdoors, you must use a GFIprotected AC outlet with “in-use” waterproof cover.
Important Safety Instructions Ventilation: Adequate ventilation must be maintained to ensure reliable and continued operation and to protect the television from overheating. Do not block ventilation slots and openings with objects, or install the television in a place where ventilation may be hindered. There must be at least 1.5” of space on all sides. Power cord protection: The power cord must be routed properly to prevent people from stepping on it, or objects from resting on it.
Table of Contents Important Safety Instructions 2 Table of Contents 5 Supplied Accessories 6 TV Installation Choose a Location for the TV 6 Detachable Speaker Module Installation 7 Rear Panel Internal Connect Source 8 Rear Panel Connection Diagrams 9 Side Panel and Front Panel Controls 18 Remote Control Guide 19 On-Screen Display Controls 21 Adjusting On-Screen Displays 21 Picture Menu 21 Audio Menu 22 Time Menu 23 Setup Menu 24 Lock Menu 26 Channel Menu 29 Trouble Shooting
Supplied Accessories Unpacking After unpacking the SunBriteTV television, please make sure that the following items are included in the carton and that they are in good condition. If items are damaged or missing, contact your dealer immediately.
TV Installation - Detachable Speaker Module Installation Detachable Speaker Module Installation Tools Needed: Phillips screwdriver Note: a. If you mount the TV on the Table Stand, the Detachable Speaker Module must be installed before you attach the Table Stand. b. If you mount the TV to a ceiling or wall mount, it is best to install the Detachable Speaker Module after the TV has been mounted. Figure 1 1. Prepare a flat work surface, free of any debris or items which may scratch the front surface of the TV.
TV Installation – Rear Panel Internal Connect Source Rear Panel Connections WARNING: Do not connect the power source before making connections. Internal Connect Source The Internal Connect Source allows you to easily connect to the Audio, Video, S-Video, SVGA, HDMI, Audio Out, RF, RS232, and 12 VDC connectors, and the IR emitter window. The Internal Connect Source is inside the Cable Cover located on the back of the unit (Figure1). 1.
TV Installation – Rear Panel Connections 1 3 2 4 5 6 8 9 7 9 12 10 11 13 14 15 16 1. SERVICE PORT - This USB Service Port is for factory service only...do not use. 2. SERVICE PORT - This Service Port is for factory service only...do not use. 3. HDMI 1 - Connects to devices that use HDMI cables such as Blu-ray or HD DVD player or HD cable / satellite set-top box. This connection port receives pure digital audio and high definition signal through one single cable.
TV Installation – Rear Panel Connections Connection Descriptions: Cable Descriptions: Red Green Blue Yellow Green Red White Page 10
TV Installation – Rear Panel Connections/Connection Diagrams Switching Sources for Ports: Model 6560HD offers several options when connecting your devices to the TV. The chart below will help you understand which source you switch to for each of the ports. CONNECTING TO AN ANTENNA Connecting to Digital Cable without Cable Box or Antenna Connecting to Cable or Antenna 1. Make sure the power to the TV is turned off. 1. Make sure the power of the TV is turned off. 2.
TV Installation – Rear Panel Connection Diagrams CONNECTING TO AN ANTENNA--(Continued) Connecting to Cable or Antenna through VCR 1. Make sure the power of the TV is turned off. 2. Make sure there is an antenna or cable connection to the VCR already. 3. Use a Coaxial RF cable and connect from your VCR’s Antenna Out or Output to TV to the ATSC/ NTSC port of your TV. 4. Turn on the TV. 5.
TV Installation – Rear Panel Connection Diagrams CONNECTING TO A DVD PLAYER (Continued) Connecting with S-Video (fair) 1. 2. 3. 4. 5. 6. Make sure the power of the TV and your DVD player is turned off. Obtain an S-Video Cable. Connect the S-Video connector to both your DVD player and Composite’s S-Video connector port off the back of your MODEL 6560HD. Obtain a RCA Audio Cable.
TV Installation – Rear Panel Connection Diagrams Connecting with Component (Better) CONNECTING TO A SATELLITE OR CABLE SET-TOP BOX Connecting with HDMI (Best) 1. 2. 3. 4. 1. Make sure the power of the TV and your set-top box is turned off. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port off the back of your TV. Turn on the TV and your set-top box. Use the remote control’s source button or the source button on the right side of the TV to switch to HDMI 1.
TV Installation – Rear Panel Connection Diagrams CONNECTING TO A SATELLITE OR CABLE SET-TOP BOX (Continued) Connecting with Composite (Fair) Connecting with S-Video (Fair) 1. 2. 3. 4. 5. 6. Make sure the power of the TV and your DVD player is turned off. Obtain an S-Video Cable. Connect the S-Video connector to both your DVD player and Composite’s S-Video connector port off the back of your MODEL 6560HD. Obtain a RCA Audio Cable.
TV Installation – Rear Panel Connection Diagrams CONNECTING TO AN EXTERNAL AMPLIFIER OR AMPLIFIED SPEAKERS Connecting with Coaxial SPDIF Digital (Best) Connecting with RCA Audio Analog (Good) 1. 1. 2. 3. 1. Make sure the power of the TV and your receiver is turned off. Obtain a Coaxial SPDIF cable, connect it to your receiver’s coaxial SPDIF digital input and the Coaxial SPDIF connection on the LINE OUT port off the back of the TV. Turn on the TV and your receiver. 2. Please Note : 1. 2. 3.
TV Installation – Rear Panel Connection Diagrams CONNECTING TO A PC (Continued) Connecting with RCA Audio Analog (Good) 1. 2. 3. 4. 5. Make sure the power of the TV and your PC is turned off. Obtain a 15-pin D-Sub VGA cable, connect to the VGA output of your PC and the other end to the VGA port off the back of your TV. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC and the other end to the VGA Stereo Input port. Turn on the power of the TV and your PC.
TV Installation--Rear Panel Connection Diagrams Connecting the Power Cord WARNING: TV AND GFCI RECEPTACLE MUST BE INSTALLED AT LEAST 5 FEET AWAY FROM STANDING WATER , SUCH AS (BUT NOT LIMITED TO) A POOL OR SPA. Connect the power cord after you have made connections to your video equipment. Connect the power cord to a GFCI-protected AC outlet with “in-use” waterproof cover. Warning: TV must be installed at least 5 feet away from standing water, such as (but not limited to) a pool or spa.
Remote Control Guide ON – Powers the TV On. OFF – Powers the TV Off. 0~9 – Allows you to set the channels directly. To access a digital channel, use these buttons with the (-) button to switch channels. Dash (-) – Insert the dash for selecting digital channels directly. R – Returns to the previous channel. FREEZE – Freezes the TV picture. Press the button again to unfreeze the picture. SLEEP– Sets time for the TV to turn Off. CC– Selects Closed Caption (CC only works under sources TV, AV1 and AV2.
Remote Control Guide This remote control follows Sony’s TV remote codes with discrete on/off and input select. Direct TV code is 10,000 About the Water-Resistant Remote Control The SunBriteTV® Water-Resistant Remote Controller is engineered to give you many years of service. “Water-resistant” means that the remote control can be in water for short periods of time without damaging the internal workings of the unit. It can be left in the rain, and even dropped in water, as long as it is retrieved quickly.
On-Screen Display Menu - Picture Menu Your TV has been factory-set to plug-in and enjoy your programming. In the event you turn on the TV and get the message, “Please run Channel Auto Scan,” press your remote’s Menu button, press the Channel function and press Auto Scan. Note: To run the Channel function, you must be in the TV Source. To access the TV source, click Input on the TV’s side panel or Source button on the Remote Control. Press TV from the Input Select option.
Adjusting On-Screen Displays – Audio Menu Audio Menu 1. Press qp buttons to move the cursor to the item to be selected. 2. Press t u buttons to make the desired adjustments. 3. When you are satisfied with your adjustments, press MENU or EXIT to exit the main menu. Sound Mode Sound Mode Allows you to you choose your sound preferences. Press qp buttons to Sound Mode, then use t u to adjust the Sound Mode such as Personal/Standard/ Music/Movie.
Adjusting On-Screen Displays – Time Menu Time Menu 1. Press qp buttons to move the cursor to the item to be selected. 2. Press u buttons to make the desired adjustments. 3. When you are satisfied with your adjustments, press MENU or EXIT to exit the main menu. Time Menu Sleep Timer Press qp buttons to Sleep Timer, then use t u buttons to select the sleep timer. The options are: Off; 5Min; 10Min; 15Min; 30Min; 45Min; 60Min; 90Min; 120Min; 180Min; 240Min.
Adjusting On-Screen Displays – Setup Menu Setup Menu 1. Press qp buttons to move the cursor to the item to be selected. 2. Press t u buttons to make the desired adjustments. 3. When you are satisfied with your adjustments, press MENU or EXIT to exit the main menu. Menu language Press qp buttons to Menu Language, then use t u buttons to select menu language, the options are English / French / Spanish.
Adjusting On-Screen Displays – Set Up Menu Closed Caption From the Setup Menu, press qp buttons to Closed Caption, then press u button to enter the Closed Caption submenu list shown below. Closed Caption Submenu Basic Selection Press qp buttons and then use t u buttons to select current zoom mode, the options are CC1 / CC2 / CC3 / CC4 / TEXT1 / TEXT2 / TEXT3 / TEXT4.
Adjusting On-Screen Displays – Lock Menu Lock Menu Press qp buttons to move the cursor to the Enter Password selection. Press “Enter Password” to enter the password. (The default password is 0000.) To change the Password, press the u button to enter the Lock Menu submenu Lock Menu Sub-Menu Change password Press u button to enter the submenu. Once there, you can enter the new password and confirm it. The password will be changed.
Adjusting On-Screen Displays – Lock Menu US Menu From the US Menu, press qp buttons to the TV function. Press u button to enter the submenu shown below.
Adjusting On-Screen Displays – Lock Menu Lock Menu Sub-Menu Canada Press the u button to enter the submenu for the Canadian rating functions. Canada Menu Canada English Press the t u button to select one of E / C / C8+ / G / PG / 14+ / 18+. Canada French Press the t u button to select one of E / G / 8ans+ / 13ans+ / 16ans+ / 18ans+.
Adjusting On-Screen Displays – Parental Menu Channel Menu 1. Press qp buttons to move the cursor to the item to be selected. 2. Press t u buttons to make the desired adjustments. 3. When you are satisfied with your adjustments, press MENU or EXIT to exit the main menu. Channel Menu The CHANNEL MENU can be used in the TV Source mode only. To access the TV Source, click Input on the TV’s side panel or the Source button on the Remote Control. Press TV from the Input Select option.
Adjusting On-Screen Displays – Channel Menu Favorite Favorite From the Channel Menu, press the qp buttons to select Favorite. Press the u button to enter the submenu shown at left. Press qp keys to select channels, and press OK to add current channel to Favorite Channel Table. Follow the same directions to delete a channel from the Favorite Channel Table. Show/Hide Menu Show/Hide From the Channel Menu, press the qp buttons to select Show/Hide. Press the u button to enter the submenu (shown left).
Trouble Shooting The following table contains the common problems and the solutions to these problems. Please check this list before you contact the technicians. Trouble Solutions Trouble Solutions No picture Check the following: Power cord is connected correctly. Power is turned on. The video cable is connected correctly. You have selected the proper input signal source. If you have done the above, without resolve, unplug TV for at least one hour to perform Hard Reset.
Care of SunBriteTV Caring for the LCD Panel 1. Cleaning the LCD Panel: With your TV turned off, gently wipe the surface of the display panel with a damp (with water) microfiber, cotton or flannel cloth. (Do not use tissues, rags, sponges or paper towels because they may damage the screen and leave lint pieces behind).
Specifications Specifications for SunBriteTV Model 6560HD LCD Screen 65-inch diagonal TFT Active Matrix Resolution 1920 x 1080 full-HD 1080p Aspect Ratio 16:9 Contrast Ratio 5000:1 Frame Rate 240 Hz H/V Viewing Angle 176o Response Time 6.
Features Information and Instructions Extreme Climate Warning If temperatures below -24O F. are expected, we recommend that you bring your SunBriteTV inside to prevent damage to the LCD screen. Programming Other Manufacturers’ Universal Remote Control Devices When programming a DirectTV, local cable universal remote control or Control system, you may find that SunBriteTV is not on the list of TV manufacturers. If that is the case, this model supports SONY’s universal remote code.
IR Emitter Installation Tie-Down IR Window To install the IR Emitter: The photo to the right shows an IR Emitter* installed. The end of the Emitter is to be mounted in front of the IR Emitter Window. Place the emitter on the white tie-down block and use the tie-down to secure it in place. Place the emitter cable over the right or left side of the cable box and connect the other end of the emitter to the appropriate control block*. * Neither the emitter or control block are supplied by SunBriteTV.
Appendix A - RS232 Control Codes Com Spec: 9600,8,1,n Page 36 RS 232 Control codes SunbriteTV Function ASCII HEX Command Received Response from TV to control system Model Class ID [ESC]? 1B 3F [B3220AHD-X.XX] or [B4610AHD-X.
Appendix B - RS232 Control Cable Pinout DB9F, Typical PC Serial / Control System RS232 port.
This page is intentionally left blank.
This page is intentionally left blank.
www.sunbritetv.
