Tools Needed for Installation ANA a 2 2 Easy Bolt Easy Driver 010210410 BMS7780/BMS7786 Modern™ Storage Shed ASSEMBLY INSTRUCTIONS i J] IE Quality Control Number: KEEP THESE INSTRUCTIONS. You will need Quality Control Number shown below to register your product.
py Before You Begin... + Consult your local authorities for any permits required to construct shed. Prior to the construction of your shed, check with the local building code official to review any required permits ar building limitations. + A level and sturdy foundation is required before shed construction can begin. Site preparation information is available on pages 10-11. A foundation that differs from the suggestions within this manual could prevent proper assembly and may damage parts.
A Shed Safety and Care = Hot items, such as recently used grills, blowtorches, etc., must not be stored in the shed. * Heavy articles should not be leaned against the walls, as this may cause panel distortion and permanent damage. + Keep roof clean of snow and leaves. * The shed walls and roof sections have a textured exterior, much like vinyl home siding. Over time, dust may accumulate in the texture. When combined with moisture, this could encourage the growth of moss or mold on the shed.
Parts Walls and Floors IMPORTANT OPEN ALL BOXES FIRST AND NEATLY LAYOUT PARTS. SMALL PARTS MAY BE CONTAINED IN EACH BOX. PLEASE REFERENCE THE PARTS LIST WITHIN THIS MANUAL TO VERIFY ALL PARTS ARE PRESENT, COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL PARTS.
Parts Doors IMPORTANT OPEN ALL BOXES FIRST AND NEATLY LAYOUT PARTS. SMALL PARTS MAY BE CONTAINED IN EACH BOX. PLEASE REFERENCE THE PARTS LIST WITHIN THIS MANUAL TO VERIFY ALL PARTS ARE PRESENT. COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL PARTS.
Roof Headers Windows IMPORTANT OPEN ALL BOXES FIRST AND NEATLY LAYOUT PARTS, SMALL PARTS MAY BE CONTAINED iN EACH BOX, PLEASE REFERENCE THE PARTS LIST WITHIN THIS MANUAL TO VERIFY ALL PARTS ARE PRESENT. COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL PARTS.
Parts Roof Steel IMPORTANT ALL PARTS ARE PRESENT. UNPACKING ALL PARTS. OPEN ALL BOXES FIRST AND NEATLY LAYOUT PARTS. SMALL PARTS MAY BE CONTAINED IN EACH BOX. PLEASE REFERENCE THE PARTS LIST WITHIN THIS MANUAL TO VERIFY COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE ® 0 TMRO05006 — Truss Leg TJ 1MPO00023 x3 Support Bracket x4 ANTIPROTON [] Ridge Beam 1MR004005 Side adapter, 1MRO04005 Wall adapter, L.
0480375 ~ Hardware bag 625" Screw x315 Wall Adapter Cap NINCOMPOOP — Metal hinge plate x6 .25" Locking nut x12 0480337 ~ Hardware bag Hardware bag 0440990 Window Gaskets o 25" x .75" Screw x6 28 Locking ut “Easy Holt easy driver Hardware shown at actual size ("unless otherwise noted). Extra hardware provided. Not all are used.
x4 Parts Door Handle Kit 0463795 ~ Door handle kit 0 0102479 Door handle x2 0463797 ~ Door latch kit OMP0O0020 — Left latch plate 0463812 — Door Latch Assembly #10 x 1" Fender washer #0x21/4" Pan head screw x4 (LL) .25" Washer x4 .25" Locking nut x4 Hardware shown at actual size (*unless otherwise noted). Extra hardware provided. Not all are used.
Site Preparation and Platform Construction Materials NOT supplied with Shed Kit Note: Site preparation is required for this shed. Placing the shed on a constructed foundation is required, Without a constructed foundation, settling will probably occur, causing distortion and damage to the shed. Sun cast is not responsible for replacing parts damaged or property lost due to incorrect assembly. Warranty requires foundation.
Site Preparation and Platform Construction (continued) Materials NOT supplied with Shed Kit Wood platform critical spacing * Check all critical spacing measurements, Wood platform materials list a 1 37.25" x 84.75" 84.75" x .76" 84.75" d 8 82.25" 11.75" « Please note-dimensional lumber is actually 1/2" smaller than noted sizes.
Header Pr-Assembly At top interior side of left door (J), attach D-ring slide At bottom interior side of left door (J), attach D-ring slide bolt {0} with four screws (NN) through provided holes. bolt (0) with four screws (NN) through provided holes. Place Front Header (L} on flat surface, facing down. Place Left Side Header (W) on flat surface facing down. insert one gasket {P) into the groove around each Insert one gasket (P} into groove around window window opening.
Header Pr-Assembly Place Front Header (L} face down on flat surface. Place one header beam (Y} in each channel above and below the window openings. Secure Beams (Y) with eight screws {NN}. Place short side adapter (GC) between windows with the flat bottom end facing down. Secure adapter {CC} with four screws (NN). Place Rear Header (Q) face down on flat surface. Place remaining header beam {Y} in channel on back of header. Secure Beam (Y) with four screws {NN}.
Note: Use a rubber mallet to “push” left front Align tab on bottom right side of left front corner (8) with comer (B) into locked position, slot on front floor (A). Lower panel into slot and lock in place by sliding panel forward outside of floor. T Tip left front corner (B) back to vertical position and align lower tabs on right side with slots in floor. Shed Assembly Floors and Walls Push front floor (A) and rear floor (T) panels together and secure with six screws (NN).
Before proceeding, make sure comer is square {top view) where it meets the floor and that panel is flush (side view} with floor. If not, repeat Steps 8-10 until square and flush. T Top view ar | Side view 16 Align tabs on bottom of side panel {N} with slots along front and rear floors. Lower panel into slots and lock in place by sliding panel toward front corner. Note: Use a rubber mallet to “push” side panel (N} into locked position.
Place Front Header (L} over door opening and fit two protruding support tabs into pockets in front corners. Secure front header with four screws (NN). 17 Place Rear Header {Q) over back wall and fit the four protruding tabs into pockets provided in wall. Secure rear header with eight screws (NN) TIP: Have a second person hold wall from inside Place Left Side Header {W) over left side walls.
Place one Side Adapter {BB} in position on right side of interior door opening. Secure with 12 screws (NN). Place one side adapter (BB) in position on back corner. Secure with 12 screws (NN). Note: Critical Orientation of bracket is shown and used in next steps. Repeat steps with the remaining two side adapters {BB) on left side of the shed interior. SIDE x2 Attach one wall adapter (EEE) to right side wall by sliding it in place from above.
Place Ridge Beam {DD} into top of the two wall mounted side adapters. Secure with one bolt {JJ} and one nut {LL} at each end of the ridge beam. Attach three Support Brackets {Z} to the front of the Ridge Beam (DD) using two screws (NN).
Place one Truss Leg (AA) over the side adapters and support bracket on the back wall, ridge beam, and the front header. Secure into the three brackets with bolts (JJ) and Nuts {LL}. Repeat steps for the remaining two truss legs (AA). Line up one Roof Panel {M) with the right side header so the tabs on the header align with the five slots in the roof panel. NOTE: The wide band on the roof panel faces front.
x5 Line up the remaining roof panel {M) on the left side header with header tabs fitting into roof panel slots. Slide the roof panel toward the back wall to fully engage the five attachment features. Secure roof panels (M) to the top of the front header {L) using ten screws (NNJ.
Shed Assembly/Roof Panels Secure roof panels {M) to the top of the back header using ten screws (NN). Note: For clarity, illustration is shown with some parts removed, Each truss leg (AA) is secured to the roof panels (M} with 16 screws (NN).
Shed Assembly/Doors Stand right door {K} upright with three hinge mounts facing right. Slide one metal hinge plate (If) up onto each With metal hinge plates in open position, slide one hinge over each hinge receptacle on inside of right front panel. hinge mount. Rotate hinges to outside of door. Note: For clarity, illustration is shown with roof removed. 7 Note: Use a rubber mallet if necessary. Insert two screws {CCC} into right latch plate (XX) and through right door.
Shed Assembly/Doors insert screws (CCQ) into left latch plate (WW) and through Fran the outside of doors, insert door handle {VV} left door. While holding plate in place on exterior of door, stems into holes of left and right doors, On inside of secure each screw with two washers (AAA) and two doors, place washers (YY} on each door handle stem, locking nuts {BBB}. -DO NOT Overattentive secure each with one screw (ZZ). -DO NOT Enlightenment upper D-ring (O} up to engage in front of header.
SUNCAST® Building, Shed and Gazebo Ten Year Limited Warranty Your SUNCAST® Building, Shed or Gazebo has a TEN YEAR LIMITED WARRANTY against product failure resulting from defects in manufacturing or materials. The warranty period starts on the delivery date. Incidental and consequential damages are nat covered Warranty Claims Te file a warranty claim contact the manufacturer, SUNCAST® CORPORATION, 701 North Kirk Road, Atavist, lino is. 60510. Call toll free (800) B482345 or visit www.
