Instructions / Assembly

ManualsBrandsSuncourt ManualsHeating, Ventilation, and Air ConditioningRadon Mitigation Fan Kit 4 in. Fan with 4 in. to 3 in. Couplers and Air Pressure Indicator

Radon Print

http://suncourt.com/Radon%20Print.html[3/8/2012 1:49:07 PM]

SUNCOURT® RADON FAN MODEL: RDN04 & RDN04-3,

RDK04 & RDK04-3 INSTALLATION INSTRUCTIONS

READ THESE INSTRUCTIONS BEFORE PLANNING YOUR INSTALLATION

PLEASE READ AND SAVE THESE INSTRUCTIONS:

DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED.

CAUTION: BEFORE CARRYING OUT ANY MAINTENANCE OR SERVICING, ENSURE

THE UNIT IS DISCONNECTED FROM THE MAIN POWER SUPPLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS OR DUST.

NEVER EXPOSE THIS FAN TO TEMPERATURES EXCEEDING 140°F (60°C).

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Do not use fan in hazardous environments where the fan electrical system could

provide ignition to combustible or flammable materials.

2. Do not use fan to exhaust explosive or corrosive gases.

3. Check voltage at the fan to insure it corresponds with product nameplate.

4. Normal operation of this device may affect the supply of fresh air needed for safe

operation of fuel burning equipment. Follow safety standards, codes, and heating

equipment manufacturer’s procedures guide lines.

5. There are no user serviceable parts located inside the fan unit. Do NOT attempt to open

(this will void manufacturer’s warranty). Return unit to the factory with original purchase

receipt for service after obtaining a Return Goods Authorization (RGA).

6. All wiring must be in accordance with local and national electrical codes. When installed

outside, power must be supplied from a GFCI (Ground Fault Circuit Interruptor).

7. Operate unit only in the manner intended. If you have questions, contact the

manufacturer.

8. Before servicing or cleaning unit, switch power off at service panel and lock service

panel to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such

as a tag to the service panel.

9. Installation work and electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards, including fire-rated construction.

10. This unit has an unguarded impeller. Do not use in locations where the impeller is

Summary of content (7 pages)

PAGE 1
Radon Print SUNCOURT® RADON FAN MODEL: RDN04 & RDN04-3, RDK04 & RDK04-3 INSTALLATION INSTRUCTIONS READ THESE INSTRUCTIONS BEFORE PLANNING YOUR INSTALLATION PLEASE READ AND SAVE THESE INSTRUCTIONS: DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED. CAUTION: BEFORE CARRYING OUT ANY MAINTENANCE OR SERVICING, ENSURE THE UNIT IS DISCONNECTED FROM THE MAIN POWER SUPPLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS OR DUST.
PAGE 2
Radon Print readily accessible to people or animals. 11. This unit can be used with the Suncourt VS100 or VS200 solid state speed control. (Sold Separately) (1) Running watts at zero static pressure (2) Watts range at varying static pressure FAN SPECIFICATIONS Electric Motor • External Rotor • Ball Bearing • Class B • Thermally Protected • Conforms To ANSI-UL 705 & CSA 22.2 • ETL Listed • Housing Material FRABS • UV Protected • Flame Rating UL 94V0 • Housing Color White http://suncourt.
PAGE 3
Radon Print INSTALLATION Retain original packaging. The fan can be mounted indoors or outdoors. (It is suggested that EPA recommendations be followed in choosing the fan location.) The fan may be mounted directly to the system piping or fastened to a supporting structure by means of mounting brackets provided. MOUNTING Mount the fan vertically with the outlet up. Insure the unit is plumb and level.
PAGE 4
Radon Print MOUNTING BRACKET The fan may be further secured with the mounting brackets provided. The flexible couplings will provide means of disconnect for cleaning the impeller and also to isolate vibration. ELECTRICAL WIRING The fans operate on standard 120V 60 Hz AC. All wiring must be performed in accordance with the National Electrical Code and state and local building codes. A qualified electrician should perform all electrical work.
PAGE 5
Radon Print CONDENSATION & DRAINAGE Condensation can form in the piping of a mitigation system when the air in the piping is chilled below its dew point. This can occur at points where the system piping goes through unheated space such as an attic, garage or outside. The system design must provide a means for water to drain back to a slab hole to remove the condensation. The fan MUST be mounted vertically plumb and level, with the outlet pointing up for proper drainage through the fan.
PAGE 6
Radon Print The bypass is constructed with a 45 degree Wye fitting at the bottom of the outlet stack. The bottom of the Wye is capped and fitted with a tube that connects to the inlet piping or other drain. The condensation produced in the outlet stack is collected in the Wye fitting and drained through the bypass tube. The bypass tubing may be insulated to prevent freezing. Failure to install a proper condensate collection system voids the product warranty.
PAGE 7
Radon Print FIVE YEAR LIMITED WARRANTY Subject to the following limitations, Suncourt Inc. (manufacturer) warrants that the fan will, for 5 (five) years from date of original purchase, remain free from appearance of defects in workmanship or materials.