Instructions / Assembly

ManualsBrandsSuncourt ManualsKitchen10 in. Automated Damper Normally Closed

ZonePrint

http://www.suncourt.com/ZoneMasterPrint.html[1/16/2012 3:22:55 PM]

INSTALLATION INSTRUCTIONS FOR

ZONEMASTER™

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

For general ventilation control use only.

Do not use to control the flow of hazardous, corrosive, flammable or explosive materials

and vapors.

Never expose this product to temperatures exceeding 140°F (60°C).

Always leave this product accessible for maintenance, cleaning and repair.

Before installing or servicing this product, switch power off at the service panel

and lock service to prevent power from being switched on accidentally.

Suncourt® Inc. assumes no responsibility for the installation of the ZoneMaster™.

Suncourt® does not provide electrical connection information beyond what is provided

herein.

If in doubt, contact a competent contractor.

For your safety and protection follow all instructions and adhere to applicable building and

electrical codes.

WARNING

To reduce the risk of fire, electric shock or injury to persons, observe all instructions. The

ZoneMaster™ has been designed to operate on 24 Volt AC, 60 Hz. The only 110/120 Volt

AC connection needed is for the power supply Transformer. Before installing the

Transformer, confirm that the electric power is off at the junction box where you will be

making the Transformer 110/120 Volt connections. Observe the following clearance to

combustible materials or surfaces: For both the Transformer and the Damper electric motor:

a minimum of 4” (10 cm) is required.

This damper is designed to control the flow of heated or cooled air in air distribution

systems only. Never close more than 20% of the air ducts leading to registers. The restricted

airflow through a furnace or central air conditioner may cause failure of that equipment.This

damper must never be used to control the flow of combustion air, flue gas or other toxic or

hazardous gases or applications where failure of the damper can cause damage to persons,

property or equipment and/or create a risk of fire, suffocation or death.

Summary of content (6 pages)

PAGE 1
ZonePrint INSTALLATION INSTRUCTIONS FOR ZONEMASTER™ READ AND SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS For general ventilation control use only. Do not use to control the flow of hazardous, corrosive, flammable or explosive materials and vapors. Never expose this product to temperatures exceeding 140°F (60°C). Always leave this product accessible for maintenance, cleaning and repair.
PAGE 2
ZonePrint IMPORTANT NOTES The following will be required to complete the installation: • A standard low voltage Heat-Cool wall thermostat, designed for gas furnaces. • Electrical wire, 2-conductor, 20 Gauge (CL-2 or Bell Wire) to connect the Transformer to the Damper via the wall thermostat. If the total length of wire exceeds 80 feet (25 m), use 18 Gauge wire. • A cover plate with knockout for the electrical box that the Transformer will be mounted on.
PAGE 3
ZonePrint hardware normally supplied with the thermostat. Do not mount the thermostat on an outside wall. Locate the thermostat approximately 5’ (1.5 m) above the floor and away from drafts and direct sunlight. DO NOT screw the thermostat to the wall at this time. Transformer installation: IMPORTANT WARNING: Locate the breaker on your house power panel that controls the 110/120 Volt AC supply to the wires in the junction box that you selected to mount the Transformer on.
PAGE 4
ZonePrint 1. Run one wire from either Transformer low voltage terminal to either terminal on the Damper. 2. Run one wire from the other Transformer low voltage terminal to the terminal marked “R” on the thermostat. 3. Run one wire from the other terminal on the Damper to the terminal marked “W” on the thermostat. 4. Connect the terminals “W” and “Y” on the thermostat together with a short piece of wire (jumper). THE WIRING IS NOT POLARITY SENSITIVE. CONNECT EITHER SCREW ON TERMINAL BLOCK OR TRANSFORMER.
PAGE 5
ZonePrint installed safely and securely, you may turn on the breaker on your house power panel. MAINTENANCE Suncourt® recommends that you clean your damper at regular intervals to keep it free from lint, dust and debris. The damper must never be exposed to temperatures over 140°F (60°C). OPERATING INSTRUCTIONS 1. Set the switch on the thermostat marked ‘ON-AUTO’, ‘ON-OFF-AUTO’, ‘ON-OFF’ or similar wording, to the ‘ON’ position. 2. Heating Season: Set the thermostat to ‘HEAT’.
PAGE 6
ZonePrint http://www.suncourt.com/ZoneMasterPrint.