Gas Stand-Up Heater SKU:F18B411 & F18G412 & F18S413 5016039 Byphone:+1-626-4201-198 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
SKU:F18B411 & F18G412 & F18S413 DANGER WARNING If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odour continues, keep away from the appliance and immediately call your gas supplier or fire department. Caution Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
DANGER CARBON MONOXIDE HAZARD This heater is a combustion appliance. All EXPLOSION - FIRE HAZARD Keep solid combustibles, such as building materials, combustion appliances produce carbon monoxide (CO) during the combustion process. This product is designed to produce extremely minute, non-hazardous amounts of CO if used and maintained in accordance with all warnings and instructions. Do not block air flow into or out of the heater.
SKU:F18B411 & F18G412 & F18S413 WARNING WARNING Caution California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. WARNING BURN HAZARD Never leave heater unattended when hot or in use. Keep out of reach of children. WARNING Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged.
Assembly Procedures 5 KK LL and 12 pcs packed in MM Zip lock bag, together with wheels AA BB CC DD EE FF GG HH II JJ KK LL MM M6 Cap Nut M6*8 Bolt Reflector Stud Wing Nut M6*12 Bolt M6*30 Bolt M6 Nut Anchoring Arm M8*15 Bolt M8 Big Washer M6/M8 Wrench Anchoring Cylinder Fixer 9 9 3 3 12 6 18 3 3 9 1 3 3 NO H040040005 H010110049 H020040001 H040030005 H010010019 H010010020 H040010003 P000501127 H010010021 H050010018 H090020002 P000100315 P002200208 A B C D E F G 5 Reflector Flame screen Burner Post
Assembly Procedures 6 SKU:F18B411 & F18G412 & F18S413 Secure the cylinder fixer (MM) with two M6 bolts (EE) and nuts (GG). Fix another two cylinder fixers (MM) with bolts and nuts, and reverse the base (G). M KK Secure the ground fixer (HH) with two M6 bolts (EE) and nuts (GG). Fix another two ground fixers (HH) with bolts and nuts, and reverse the base (G). Note: To secure the unit, please use three nails LL to nail the unit to the ground.
STEP 1 1-1. Position the 3 post brackets on the base as shown in the picture. 1-2. Use 3 bolts (M8 x 15 mm) to assemble the post, brackets and stand. G STEP 2 GG 2-1. Put the post on the top of 3 post brackets. 2-2. Use 6 M6 bolts (FF) and nuts (GG) to connect the post to the 3 post brackets. Tighten the bolts and nuts. STEP 3 3-1. Place the tank housing (E) on the base (G).
SKU:F18B411 & F18G412 & F18S413 Assembly Procedures STEP 4 4-1. Attach a reflector stud (CC) and three washers Ø8 (JJ) to the top of the burrer (C). Tighten the reflector stud. 4-2. Unscrew the four screws that are preassembled on the head assembly (C). Place the head assembly (C) into the top of the post (D) by inserting the regulator into the post (D). Tightly fasten the previously removed screws back into the head assembly (C) through the slots at the top of the post (D).
11. Screw gas hose (C) and regulator (E) onto propane 8 cylinder (not included). Do not cross-thread. C Every part of the heater should be secure against displacement and should be constructed to maintain a fixed relationship between essential parts under normal and reasonable conditions of handling and usage. Parts not permanently secured should be designed so they cannot be incorrectly assembled and cannot be improperly located or misaligned in removing or replacing during cleaning or other servicing.
A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. 17.9 in. / 45.5cm Assembly Instructions SKU:F18B411 & F18G412 & F18S413 The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S.
To check for a leak: 1. Make 2-3 oz. leak check solution (one part liquid dishwashing detergent and three parts water). Perform all leak tests outdoors. Extinguish all open flames. NEVER leak test when smoking. Do not use the heater until all connections have been 2. Apply several drops of solution where regulator connects to cylinder and to all hose and valve connections. leak tested and do not leak. 3. Make sure all patio heater and light valves are OFF. 4. Turn cylinder valve ON.
SKU:F18B411 & F18G412 & F18S413 120 cm CEILING 120 cm CARBON MONOXIDE HAZARD For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. WALL Operation Instructions DANGER Caution: Do not attempt to operate until you have read and understood all General Safety Information in this manual and all assembly is complete and leak checks have been performed.
1. Turn on the valve on the gas cylinder. 2. Press and turn the control knob to PILOT position (anti-clockwise 90º). (Figure 1) 3. Holding down the control knob, press the igniter button several times until the main flame is ignited. Release the control knob 10 seconds after the ignition. 4. Press lightly and turn the variable control knob to HI (maximum) position and leave it there for 5 minutes or more before turning the knob to the desired temperature setting. (Figure 2) 5.
SKU:F18B411 & F18G412 & F18S413 Operation Instructions WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When Heater is ON: Emitter screen will become bright red due to intense heat. The colour is more visible at night. Burner will display tongues of blue and yellow flame.
9. Heater is away from gasoline or other flammable liquids or vapours. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 2.3 feet on top and at least 3.3 feet on sides from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
Care and Maintenance 16 SKU:F18B411 & F18G412 & F18S413 Visually check portions of the hose assembly located within the confines of the heater post. Inspect the entire hose assembly at least annually, disassembling the reflector and burner. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. Then assembling the reflector and burner again following with step 6 and 7. Gas odour with extreme yellow tipping of flame.
POSSIBLE CAUSE CORRECTIVE ACTION Wait until the propane cylinder warms up and is defrosted Propane cylinder is frosted over Burner won’t light Blockage in orifice Clear blockage Control knob is not in ON position Turn control knob to ON Gas pressure is low Turn cylinder valve OFF and replace cylinder Outdoor temperature is less than 40ºF and tank is less than 1/4 full Use a full cylinder Control knob fully ON Check burner and orifices for blockage Carbon build-up Dirt or film on reflector and b
Warranty One-year Limited Warranty 18 SKU:F18B411 & F18G412 & F18S413 This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. The Company's obligation under the warranty is to replace or repair defective parts at our discretion.
