User Guide

ManualsBrandsSUNELL ManualsNetwork CameraSUNELL SN-IPR8080CBAA-Z IR Bullet AI Network Camera

Table Of Contents

2.2 Camera Dimensions

Figure 2-2 Dimensions ฀ Unit: mm฀

NO:101-300-0679-01

Issue:1.1

IR Bullet AI Network Camera

Quick Setup Guide

Special Announcement

For more information, please refer to website.

Fully understand this document before using this device,

and strictly observe rules in this document when using this

device. If you install this device in public places, provide the

tip "You have entered the area of electronic surveillance" in

an eye-catching place. Failure to correctly use electrical

products may cause fire and severe injuries.

Ÿ Strictly observe installation requirements when installing

the device. The manufacturer shall not be held responsible

for device damage caused by users' non-conformance to

these requirements.

Ÿ Strictly conform to local electrical safety standards and use

power adapters that are marked with the LPS standard

when installing and using this device. Otherwise, this

device may be damaged.

Ÿ Use accessories delivered with this device. The voltage

must meet input voltage requirements for this device.

Ÿ If this device is installed in places with unsteady voltage,

ground this device to discharge high energy such as

electrical surges in order to prevent the power supply from

burning out.

Ÿ When this device is in use, ensure that no water or any

Ÿ Avoid heavy loads, intensive shakes, and soaking to

prevent damages during transportation and storage. The

warranty does not cover any device damage that is caused

during secondary packaging and transportation after the

original packaging is taken apart.

Ÿ Protect this device from fall-down and intensive strikes,

keep the device away from magnetic field interference, and

do not install the device in places with shaking surfaces or

under shocks.

Ÿ Clean the device with a soft dry cloth. For stubborn dirt, dip

the cloth into slight neutral cleanser, gently wipe the dirt

with the cloth, and then dry the device.

Ÿ Do not jam the ventilation opening. Follow the installation

instructions provided in this document when installing the

device.

Ÿ Keep the device away from heat sources such as radiators,

electric heaters, or other heat equipment.

Ÿ Keep the device away from moist, dusty, extremely hot or

cold places, or places with strong electric radiation.

Ÿ If the device is installed outdoors, take insect- and

moisture-proof measures to avoid circuit board corrosion

that can affect monitoring.

Ÿ Remove the power plug if the device is idle for a long time.

Ÿ Before unpacking, check whether the fragile sticker is

damaged. If the fragile sticker is damaged, contact

customer services or sales personnel. The manufacturer

shall not be held responsible for any artificial damage of the

fragile sticker.

Ÿ All complete products sold by the manufacturer are

delivered along with nameplates, quick setup guide and

accessories after strict inspection. The manufacturer shall

not be held responsible for counterfeit products.

Ÿ The manufacturer will update this manual according to

product function enhancement or changes and regularly

update the software and hardware described in this manual.

Update information will be added to new versions of this

manual without prior notice.

Ÿ This manual may contain misprints, technology information

that is not accurate enough, or product function and

operation description that is slightly inconsistent with the

actual product, the final interpretation of company is as a

standard.

Ÿ This manual is only for reference and does not ensure that

the information is totally consistent with the actual product.

For consistency, see the actual product.

Precautions

Open the package, check the appearance of product for no

obvious damage, and confirm the item list for table 1-1 is

consistent.

Table 1-1 Packing list

2.1 Device Ports

Different devices may have different ports, multi-head cables,

and fill lights; Please refer to the actual product.

Different devices may have different dimensions; Please

refer to the actual product.

NOTE

liquid flows into the device. If water or liquid unexpectedly

flows into the device, immediately power off the device and

disconnect all cables (such as power cables and network

cables) from this device.

Ÿ Do not focus strong light (such as lighted bulbs or sunlight)

on this device. Otherwise, the service life of the image

sensor may be shortened.

Ÿ If this device is installed in places where thunder and

lightning frequently occur, ground the device nearby to

discharge high energy such as thunder strikes in order to

prevent device damage.

It alerts you to moderate dangers which, if not

avoided, may cause minor or moderate injuries.

It alerts you to risks. Neglect of these risks may

cause device damage, data loss, device

performance deterioration, or unpredictable

results.

It provides additional information.

NOTE

CAUTION

WARNING

CAUTION

Device Structure

Open Package Examination

Figure2-1 Multi-head cable

Table 2-1 Multi-head cable description

Figure 2-3 Install SD card

Port

OUT

Connect to a standard Ethernet

cable or PoE. The green light is on,

the network connection is normal;

The yellow light flashes when the

data is transmitted. Some models

maybe not have the lights; Please

refer to the actual product.

Connect to an external audio

device such as a speaker.

Applied for

camera with

audio

function

Receive an analog audio signal

from devices such as a sound

pickup device.

Connect to a 12V direct current

(DC) power supply.

Alarm output COM

Applied for

alarm

function

Alarm output terminal

Alarm input COM

Alarm input terminal

Network

access port

Support PoE

supply.

Core

Description

Remark

Audio output

Power supply

(DC 12V)

Audio input

port

OUT

Reset

PWR SD

Pedestrian direction

15°

If user requires higher

accuracy of personnel count,

we recommend the user to

install camera and draw the

line following as ﬁgure 2-4.

Figure 2-4 Installation of personnel count

CAUTION

243

128

4-φ5

Bullet Network Camera

Quick Setup Guide

Installation Location Sticker

Stainless self-tapping screw

Plastic anchor

Network access port protective cover

waterproof rubber seal

L hexagon wrench

Terminal block

Component

Quantity

Remark

Summary of content (2 pages)

PAGE 1
CAUTION Ÿ Avoid heavy loads, intensive shakes, and soaking to Ÿ Ÿ Ÿ Ÿ NO:101-300-0679-01 Issue:1.1 Ÿ Ÿ Ÿ Precautions CAUTION NOTE It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries. It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results. It provides additional information.
PAGE 2
Figure 4-3 Adding a trusted site 4 Quick Configuration(e.g IE) 3 Device Installation The Bullet Network Camera can be installed on the ceiling or wall. You can select an installation mode based on site requirements. If the camera is installed on a concrete wall, install the expansion bolts before installing the bracket. If the camera is installed on a wooden wall, use self-tapping screws to install the bracket directly.