User Guide

Step 5 If camera base installation applied, press the arrows
marked on the lining to remove the lining aside. Unscrew
the three black screws and put them aside. Turn the
camera base clockwise for 5 degrees and remove it, as
shown in figure 3-3.
Step 6 Aim the three through-holes on the camera base at the
three swell plastic buttons in the ceiling, and use three
screws with a length of 30 mm to fix the base on the
ceiling. Turn the main body clockwise for about 5 degrees
to assembly it with the camera base, and fix the three
screws, as shown in figure 3-4.
Figure 3-2 Installing housing
Figure 3-1 Opening camera
Step 7 Use the Video patch cord in the accessory package to
connect the second video port. Then view the video,
adjust the lens angle horizontally and vertically, Set the
value in the Front-end Configuration for AF lens and use
the focusing lever for MF lens to adjust the lens Focal
length and video angle range, and insert the SD card.
Figure 3-3 Removing lining
and base
Installation Steps:
Step 1 Use the T15 screw driver in the accessory package to
unscrew the three screws on the dome cover. The camera
is opened, as shown in figure 3-1.
Step 2 Stick the Installation location sticker on the ceiling or wall,
Drill three holes based on the marks on the sticker. Drive
the swell plastic buttons into the holes.
Step 3 Connect the multi-head cable(If camera base installation
and aside routing selected, this step is operated after step
5).
Step 4 If camera housing installation applied, Fetch three black
self-tapping screws from the accessory package. Then fix
the screws to fasten the camera on the ceiling as shown
in figure 3-2.
The vandal dome camera can be installed in the ceiling , wall ,
wall bracket or ceiling bracket. This section describes how to
install the camera in the ceiling.
WARNING
To avoid moisture influence, install the dome cover at least
half an hour after the camera is installed and powered on.
Installation Option 1: Use holes marked with 'A' when installing camera base first. Use short ( 1.2inch length) screws and an- chors
Installation Option 2: Use holes marked with 'B' when installing complete camera housing. Use long ( 2.75 inch length) screws and anchors
A
A
A
B
B
B
Aside routing
Swell plastic
buttons
Three long
self-tapping
screws
Top routing
Black screws
Plug
Cover
Base
Three black
screws
Unscrew
Arrows
Base
Top routing
Figure 3-4 Installing base
Aside routing
Three black
screws
lining
cover
Four
buttons
T15 screwdriver
Figure3-6 Assembling
lining and base
Secondary
video port
Adjust the Focal
length and viedo
angle range
SD card slot
Main body
fixation
screws
Figure3-5 Adjusting lens
4.3 Browsing Video
To ensure the real-time video can be played properly, you must
perform the following operation when you log in the web for the first time:
Figure 4-3 Adding a trusted site
Step 2 In the Internet Explorer, choose Tool > Internet Options >
Security > Customer level, and set Download unsigned
ActiveX control and initialize and script ActiveX controls not
marked as safe for scripting under ActiveX controls and
plug-ins to Enable, as shown in figure 4-4.
Step 3 Download and install the player control as prompted.
If the repair tips displayed when installing the control , please
ignore the prompt, and continue the installation, the login page is
displayed when the control is loaded.
Step 1 the Internet Explorer. Choose Tools > Internet options >
Security > Trusted sites > Sites, in the display dialog box, click
Add, as shown in figure 4-3.
To browse a real-time video, click Live Video. The Live Video
page is displayed, as shown in figure 4-5.
4.4 Two-way a udio
Partial camera do not support two-way audio, this section do not
apply.
Figure 4-5 Live Video
Figure 4-4 Configuring ActiveX control and plug-in
Stream
Camera
Live Video
Playback
Configuration
NOTE
NOTE
Connection฀
Step 1 Connect microphone to audio input interface of camera.
Step 2 Connect speaker to the PC audio output interface.
Step 3 Log in camera Web, click to turn on two-way audio.
4.4.2 PC Camera
Step1 Connect microphone to PC audio input interface.
Step2 Connect speaker to camera audio out interface.
Step3 Log in camera Web, click to turn on two-way audio.
4.1 Login
Step 1 Open the Internet Explorer, enter the IP address of IP camera
(default value: 192.168.0.120฀ in the address box, and press
Enter. The login page is displayed. as shown in figure 4-1 .
Step 2 Input the user name and password.
Ÿ฀ The default user name is admin. The default password is admin.
Change the password when you log in the system for first time to ensure
system security.
฀ You can change the system display language on the login page.
NOTE
Step3 Click Login, the main page is displayed.
4.2 Modify IP address
Choose Configuration > Device > Local Network, the Local
Network page is displayed.
Enter the IP address in the IP Address box and click Apply as shown
in figure 4-2.
After the success of the IP address setting, please use the new IP
address to log in the Web interface.
Figure 4-2 Local Network
User Name
Password
English
Figure 4-1 Login
Local Network
IP Protocol
DHCP
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server
MTU(800-1500)
Refresh
Apply
Figure 4-6 Alarm
4.5 Alarm Configuration
Partial camera do not support alarm, this section do not apply.
Alarm input and Alarm output connection:
Step1 Connect alarm input device to Alarm IN0 and Alarm COM0
of multi-head cable.
Step2 Connect alarm output device to Alarm OUT1 and Alarm
COM1 of multi-head cable, alarm output interface can
connect to normal open device only.
Step3 Log in Web, Choose Configuration>Alarm>I/O Alarm, set
the parameters as shown in figure 4-6.
Step4 Choose Configuration>Alarm>I/O Alarm Linkage ,
enable the I/O Alarm and set the parameters of Schedule
Setting.
I/O Alarm
Alarm input
Valid Voltage Level
Name
Alarm output
Name
Alarm Time(ms)(0:Continuous)
Alarm Output Mode
Valid Signal
Manual Control
Stop
Start
Refresh
High
Close
Switch Mode
NOTE
4.4.1 Camera PC
Quick Configuration(e.g IE)
4
Step 8 Assemble the lining with the main body and buckle the four
button placements with the main body bracket. Aim the
three screws unscrewed from the dome cover in Step 1, at
the three threaded holes on the main body. Then fasten the
dome cover.
3
Device Installation