User Guide

ManualsBrandsSUNELL ManualsNetwork CameraSunell SN-IPV57 Panorama Fisheye Network Camera

Table Of Contents

NO:101-100-0450-01

Issue:1.1

Panorama Fisheye Network Camera

Quick Setup Guide

Special Announcement

For more information, please refer to website.

Fully understand this document before using this device, and

strictly observe rules in this document when using this device. If

you install this device in public places, provide the tip "You have

entered the area of electronic surveillance" in an eye-catching

place. Failure to correctly use electrical products may cause fire

and severe injuries.

It alerts you to moderate dangers which, if not

avoided, may cause minor or moderate injuries.

It alerts you to risks. Neglect of these risks may

cause device damage, data loss, device

performance deterioration, or unpredictable results.

It provides additional information.

Ÿ Strictly observe installation requirements when installing the

device. The manufacturer shall not be held responsible for

device damage caused by users' non-conformance to these

requirements.

Ÿ Strictly conform to local electrical safety standards and use

power adapters that are marked with the LPS standard when

installing and using this device. Otherwise, this device may be

damaged.

Ÿ Use accessories delivered with this device. The voltage must

meet input voltage requirements for this device.

Ÿ If this device is installed in places with unsteady voltage, ground

this device to discharge high energy such as electrical surges in

order to prevent the power supply from burning out.

Ÿ When this device is in use, ensure that no water or any liquid

flows into the device. If water or liquid unexpectedly flows into

the device, immediately power off the device and disconnect all

cables (such as power cables and network cables) from this

device.

Ÿ Do not focus strong light (such as lighted bulbs or sunlight) on

Ÿ Avoid heavy loads, intensive shakes, and soaking to prevent

damages during transportation and storage. The warranty does

not cover any device damage that is caused during secondary

packaging and transportation after the original packaging is

taken apart.

Ÿ Protect this device from fall-down and intensive strikes, keep the

device away from magnetic field interference, and do not install

the device in places with shaking surfaces or under shocks.

Ÿ Clean the device with a soft dry cloth. For stubborn dirt, dip the

cloth into slight neutral cleanser, gently wipe the dirt with the

cloth, and then dry the device.

Ÿ Do not jam the ventilation opening. Follow the installation

instructions provided in this document when installing the device.

Ÿ Keep the device away from heat sources such as radiators,

electric heaters, or other heat equipment.

Ÿ Keep the device away from moist, dusty, extremely hot or cold

places, or places with strong electric radiation.

Ÿ If the device is installed outdoors, take insect- and moisture-

proof measures to avoid circuit board corrosion that can affect

monitoring.

Ÿ Remove the power plug if the device is idle for a long time.

Ÿ Before unpacking, check whether the fragile sticker is damaged.

If the fragile sticker is damaged, contact customer services or

sales personnel. The manufacturer shall not be held responsible

for any artificial damage of the fragile sticker.

Ÿ All complete products sold by the manufacturer are delivered

along with nameplates, quick setup guide and accessories after

strict inspection. The manufacturer shall not be held responsible

for counterfeit products.

Ÿ The manufacturer will update this manual according to product

function enhancement or changes and regularly update the

software and hardware described in this manual. Update

information will be added to new versions of this manual without

prior notice.

Ÿ This manual may contain misprints, technology information that

is not accurate enough, or product function and operation

description that is slightly inconsistent with the actual product,

the final interpretation of company is as a standard.

Ÿ This manual is only for reference and does not ensure that the

information is totally consistent with the actual product. For

consistency, see the actual product.

Precautions

Open the package, check the appearance of product for no

obvious damage, and confirm the item list for table 1-1 is

consistent.

Table 1-1 Packing list

2.1 Device Ports

Component

Quantity

Remark

Different device may have different ports and multi-head

cable, please refer to the actual product.

Figure 2-1 Hardware ports

Port Name

Table 2-1 Hardware ports description

Panorama Fisheye Network Camera

Black stainless self-tapping screw

KA4.0×30mm

Swell plastic button φ5.6×29mm

Installation location sticker

Quick Setup Guide

Power supply

indicator

The indicator on when connect to the power

supply.

Description

NOTE

this device. Otherwise, the service life of the image sensor may

be shortened.

Ÿ If this device is installed in places where thunder and lightning

frequently occur, ground the device nearby to discharge high

energy such as thunder strikes in order to prevent device

damage.

Flat-head screwdriver

NIC indicator

When there is a network activity, the indica-

tor flashes.

Figure 2-2 Multi-head cable

Table 2-2 Multi-head cable description

Network

access port

Connects to a standard Ethernet

cable.

Power supply

(DC 12V)

Connects to a 12V(-15%-+10% )

direct current (DC) power supply.

Core

Description

Remark

Audio input

port

Connects to an external audio

device such as a speaker.

Audio output

port

Receives an analog audio signal

from devices such as a sound

pickup device.

2.2 Camera Dimensions

Figure 2-3 Dimensions（Unit:mm）

Different device may have different dimensions, please refer

to the actual product.

NOTE

CAUTION

WARNING

CAUTION

Applied

for

camera

with audio

function

Gray core

Orange core

Yellow core

Purple core

Alarm output terminal A(normal open)

Alarm output terminal B(normal open)

Alarm input positive terminal

Alarm input ground terminal

Applied

for alarm

function

Device Structure

Open Package Examination

Terminal block

Waterproof rubber seal

Network access port protective cover

Ø130

38.3

Summary of content (2 pages)

PAGE 1
this device. Otherwise, the service life of the image sensor may be shortened. Ÿ If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage. 1 Figure 2-2 Multi-head cable Open Package Examination 1 Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.
PAGE 2
You can install the fisheye network camera in the ceiling and wall. This section describes how to install the camera in the ceiling. 3.1 Installation Steps Step 1 Stick the Installation location sticker on the Installation surface, Drill four holes based on the marks on the sticker. Drive the swell plastic buttons into the holes, as shown in figure 3-1. Step 2 Take out the camera and remove the installation bracket, use screws with a length of 30mm to fix the installation bracket, as shown in figure 3-2.