User Guide

NO:101-100-0511-01
Issue:1.0
Vandal Dome Network Camera
Quick Setup Guide
Special Announcement
For more information, please refer to website.
Fully understand this document before using this device, and
strictly observe rules in this document when using this device. If
you install this device in public places, provide the tip "You have
entered the area of electronic surveillance" in an eye-catching
place. Failure to correctly use electrical products may cause fire
and severe injuries.
It alerts you to moderate dangers which, if not
avoided, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may
cause device damage, data loss, device
performance deterioration, or unpredictable results.
It provides additional information.
Ÿ Strictly observe installation requirements when installing the
device. The manufacturer shall not be held responsible for
device damage caused by users' non-conformance to these
requirements.
Ÿ Strictly conform to local electrical safety standards and use
power adapters that are marked with the LPS standard when
installing and using this device. Otherwise, this device may be
damaged.
Ÿ Use accessories delivered with this device. The voltage must
meet input voltage requirements for this device.
Ÿ If this device is installed in places with unsteady voltage, ground
this device to discharge high energy such as electrical surges in
order to prevent the power supply from burning out.
Ÿ When this device is in use, ensure that no water or any liquid
flows into the device. If water or liquid unexpectedly flows into
the device, immediately power off the device and disconnect all
cables (such as power cables and network cables) from this
device.
Ÿ Do not focus strong light (such as lighted bulbs or sunlight) on
Ÿ Avoid heavy loads, intensive shakes, and soaking to prevent
damages during transportation and storage. The warranty does
not cover any device damage that is caused during secondary
packaging and transportation after the original packaging is
taken apart.
Ÿ Protect this device from fall-down and intensive strikes, keep
the device away from magnetic field interference, and do not
install the device in places with shaking surfaces or under
shocks.
Ÿ Clean the device with a soft dry cloth. For stubborn dirt, dip the
cloth into slight neutral cleanser, gently wipe the dirt with the
cloth, and then dry the device.
Ÿ Do not jam the ventilation opening. Follow the installation
instructions provided in this document when installing the
device.
Ÿ Keep the device away from heat sources such as radiators,
electric heaters, or other heat equipment.
Ÿ Keep the device away from moist, dusty, extremely hot or cold
places, or places with strong electric radiation.
Ÿ If the device is installed outdoors, take insect- and moisture-
proof measures to avoid circuit board corrosion that can affect
monitoring.
Ÿ Remove the power plug if the device is idle for a long time.
Ÿ All complete products sold by the manufacturer are delivered
along with nameplates, quick setup guide and accessories after
strict inspection. The manufacturer shall not be held
responsible for counterfeit products.
Ÿ The manufacturer will update this manual according to product
function enhancement or changes and regularly update the
software and hardware described in this manual. Update
information will be added to new versions of this manual without
prior notice.
Ÿ This manual may contain misprints, technology information that
is not accurate enough, or product function and operation
description that is slightly inconsistent with the actual product,
the final interpretation of company is as a standard.
Ÿ This manual is only for reference and does not ensure that the
information is totally consistent with the actual product. For
consistency, see the actual product.
Precautions
Open the package, check the appearance of product for no
obvious damage, and confirm the item list for table 1-1 is
consistent.
Table 1-1 Packing list
2.1 Device Ports
Component
Quantity
Remark
Vandal Dome Network Camera
Swell plastic button φ5.6×29mm
Stainless self-tapping screw PA 4.0×30mm
Installation location sticker
Quick Setup Guide
1
3
3
1
1
NOTE
NOTE
this device. Otherwise, the service life of the image sensor may
be shortened.
Ÿ If this device is installed in places where thunder and lightning
frequently occur, ground the device nearby to discharge high
energy such as thunder strikes in order to prevent device
damage.
L hexagonal wrench 80×25mm
1
CAUTION
WARNING
WARNING
CAUTION
1
Open Package Examination
1
Device Structure
2
Figure 2-1 Device ports
2.2 Camera Dimensions
Figure 2-2 Dimensions of Dome(Unit:mm）
Different devices may have different dimensions, please refer
to the actual product.
NOTE
Auxiliary thread-line tool
Reset
button
Long press the button 5 seconds to
restore the original settings.
Alarm/
Audio
Alarm
out/in
out A, alarm out A
Applied
for alarm
function
out B, alarm out B
G, ground
In, alarm in
Audio
out/in
In, audio in
Applied
for audio
function
Out, audio out
G, ground
Analog
video
CVBS, analog video output
G, ground
Network
access port
Connects to a standard Ethernet cable.
12V power
supply
The ports are 12V/ OUT/12V/IN.
Uses the to auxiliary thread-line tool
through the cable
There are two rubber stoppers, user
can use the tool (screw driver or L
hexagonal wrench )to pierce the stopper,
and plug all cords in.
Remark
Over cable
rubber
stopper
Table 2-1 Interface of camera
Port name
Description
φ140
57.5
109.5
100°
φ110
123°
Over
function-
cord rubber
stopper
NOTE
Different devices may have different device ports, please
refer to the actual product.
Green terminal block 3.81-9P
Green terminal block 3.81-4P
1
1
Reset
Alarm/Audio
interface
Over-line
buckle
Network access
port
Over -line
buckle
12V power supply
interface
Over function-cord
rubber stopper
Over cable rubber
stopper