User Guide

Step 5 The set screw should be aligned the direction icon of base
panel, then rotate the device clockwise to the extreme
position, then tighten the set screw to lock block.
Figure 3-4 Install device
Figure 3-6 Assembling cover
4.3 Browsing Video
To ensure the real-time video can be played properly, you must perform
the following operation when you login the web for the first time:
If you can view the live video directly, please ignore the steps of adding
trusted sites.
Figure 4-3 Adding a trusted site
Step 2 In the Internet Explorer, choose Tool > Internet Options >
Security > Customer level, and set Download unsigned
ActiveX control and initialize and script ActiveX controls not
marked as safe for scripting under ActiveX controls and
plug-ins to Enable, as shown in figure 4-4.
Step 3 Download and install the player control as prompted.
If the repair tips are displayed when installing the control , please
ignore the prompt, and continue the installation, close the browser
during installing. Then login the page again.
Step 1 The Internet Explorer. Choose Tools > Internet options >
Security > Trusted sites > Sites, in the display dialog box, click
Add, as shown in figure 4-3.
To browse a real-time video, login the device and click Live
Video. The Live Video page is displayed, as shown in figure 4-5.
Figure 4-5 Live Video
Figure 4-4 Configuring ActiveX control and plug-in
NOTE
4.1 Login
Step 1 Open the Internet Explorer, input the IP address of IP camera
(the default value: 192.168.0.120) in the address box, and press
Enter. The login page is displayed. as shown in figure 4-1 .
Step 2 Input the user name and password.
Ÿ The default user name and password both are admin. Modify the
password when you login the system for the first time to ensure system
security.
Ÿ It is advised to restart the device three minutes later after
modifying password to ensure modified successfully.
Ÿ
Ÿ User can change the system display language on the login page.
NOTE
Step3 Click Login, the main page is displayed.
4.2 Modify IP address
Choose Configuration > Device > Local Network, the Local Network
page is displayed.
Input the IP address in the IP Address box and click Apply as shown in
figure 4-2.
After the IP address is set successfully, please use the new IP address
to login the Web interface.
Figure 4-2 Local Network
User Name
Password
English
Figure 4-1 Login
Quick Configuration(e.g IE)
4
Step 4 Plug the network access port into interface by using the
tool, as shown in figure 3-3; The power supply of the
multi-head cable and other port to interface pass through
the rubber stopper by using screw driver or L hexagonal
wrench.
Horizontal
rotating
350°
Vertical
rotating 80°
Lens axis
rotating
350°
slotted
screw
Figure 3-3 Installing housing
NOTE
Ÿ During adjusting lens, the image might be blur, set the focus
value in Sensor > Lens control page in web page.
Step 6 Connect the camera to monitor , loosen the screws of
support frame, as shown in figure 3-5. Adjust the three
axes to focus image on monitoring scenarios. Tighten the
screws to finish adjustment.
Figure 3-2 Installation
Self -tapp ing screw s
The bu mp
12V Power
supply
Network por t
Alarm/Audio
interface
NOTE
Ÿ There are two outlet mode of cable, for the top outlet mode, user
should drill the hole at first for threading cable.
Ÿ The side outlet mode that the installation sticker’s gap should
align the outlet rubber stopper.
Side o utlet
rubber stop per
Set sc rew
Bloc k
Figure 3-5 adjust lens
Step 7 Arrange the cable of camera to over-line buckle, then
assemble the dome cover with hex wrench, as shown in
figure 3-6.
hexagonal wrench
Installation Steps:
Step 1 Stick the Installation location sticker which is in accessory
package on the ceiling or wall, Drill three holes based on
the marks on the sticker. Drive the swell plastic buttons
into the holes.
Step 2 Use the wrench in the accessory package to unscrew the
three screws on the dome cover. The camera is opened,
as shown in figure 3-1. And use release the base panel
To avoid moisture influence, install the dome cover at least
half an hour after the camera is installed and powered on.
Step 3 Fetch three black self-tapping screws from the accessory
package. Then fix the screws to fasten the base panel of
camera on the ceiling as shown in figure 3-2.The position
of hook should be put at the appropriate place, which
should pass the bump as shown in figure 3-2.
Figure 3-1 Opening camera
The vandal dome camera can be installed in the ceiling , wall,
wall bracket or ceiling bracket. This section describes how to
install the camera in the ceiling.
WARNING
3
Device Installation
Swell plastic
buttons
Local Network
Network Card ID
IP Protocol
DHCP
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server
MTU(1280-1500)
Refresh
Apply
1500
192.168.0.120
255.255.255.0
192.168.0.1
1
IPv4
http:// 19 2. 168.0.120
Live Video
Playback
Personnel Count
Configuration
Not e: Activ eX is bei ng used t o play li ve vide o now
Swi tch to VL C, then p lay the v ideo
Swi tch to Pl ugin, t hen pla y the vid eo
Strea m
str eam 1
1
2
1 Personnel Count: user can query the data of personnel count,
through year, month, day. The statistics can be downloaded. The
data can be shown by line chart, histogram, list.
2 AI Live video: click the icon to view the snapshots of human face
or license plate (click “Face” or “Plate” to switch ).
The bottom page will show the captured images of vehicle and
human .
4.4 Intelligent Analysis
At "Configuration > Intelligent Analysis" interface, user can set the
parameters of Perimeter, Single Virtual Fence, Double Virtual Fence,
Multi Loiter, Converse and Personnel Count, as shown in figure 4-7 .
Figure 4-7 Intelligent Analysis
Live Vi deo
Playb ack
Perso nnel Co unt
Confi gurat ion
Dev ice Inf o
Str eam
Dev ice
Ext ernal D evice
Int ellig ent Anal ysis
Per imete r
Sin gle Vir tua l Fen ce
Dou ble Vir tua l Fen ces
Mul ti Loit er
Con verse
Per sonne l Count
Ala rm
AI Mu ltiob ject
Dev ice Rec ord
Pri vacy Ma sking
Net work Se rvice
Pri vileg e Manag er
Pro tocol
Dev ice Log
Loc al Conf ig
Mai ntena nce
Perim ete r
Ena ble
Sen sitiv ity
Out put Cha nnel
Ala rm Reco rd
SMT P
FTP U plo ad
Cle ar
Ref resh
App ly
Sun
4.5 AI Multi object
At “Configuration > AI Multi object” interface, user can enable face
detection, full body detection, vehicle detection, set the other
parameters of detection, as shown in figure 4-8.
Figure 4-8 AI Multiobject
Face Detection
Fullbody Detection
Vehicle Detection
Display Trace Info
Show Detection Area
Confidence Coefficient
Face Pixel Min(30-30 0)
Body Pixel Min(30-30 0)
Body Pixel Min(30-30 0)
Vehicle Pixel Min(30- 300)
Image Matting Qualit y
Snapshot Mode
Upload Image Interva l(1-10s)
FTP Up load Image Matting
FTP Up load Whole Image
Algorithms Library Ve rsion
A
B
Pedestrian direction
15°
If user require higher
accuracy of personnel count,
we recommend the user to
install camera and draw the
line following as figure 4-6.
Figure 4-6 Installation of personnel count
CAUTION