User Guide

NO:101-100-0515-01
Issue:1.1
Mini Dome Network Camera
Quick Setup Guide
Special Announcement
For more information, please refer to website.
Fully understand this document before using this device, and
strictly observe rules in this document when using this device. If
you install this device in public places, provide the tip "You have
entered the area of electronic surveillance" in an eye-catching
place. Failure to correctly use electrical products may cause fire
and severe injuries.
It alerts you to moderate dangers which, if not
avoided, may cause minor or moderate injuries.
It alerts you to risks. Neglect of these risks may
cause device damage, data loss, device
performance deterioration, or unpredictable results.
It provides additional information.
Ÿ Strictly observe installation requirements when installing the
device. The manufacturer shall not be held responsible for
device damage caused by users' non-conformance to these
requirements.
Ÿ Strictly conform to local electrical safety standards and use
power adapters that are marked with the LPS standard when
installing and using this device. Otherwise, this device may be
damaged.
Ÿ Use accessories delivered with this device. The voltage must
meet input voltage requirements for this device.
Ÿ If this device is installed in places with unsteady voltage, ground
this device to discharge high energy such as electrical surges in
order to prevent the power supply from burning out.
Ÿ When this device is in use, ensure that no water or any liquid
flows into the device. If water or liquid unexpectedly flows into
the device, immediately power off the device and disconnect all
cables (such as power cables and network cables) from this
device.
Ÿ Do not focus strong light (such as lighted bulbs or sunlight) on
Ÿ Avoid heavy loads, intensive shakes, and soaking to prevent
damages during transportation and storage. The warranty does
not cover any device damage that is caused during secondary
packaging and transportation after the original packaging is
taken apart.
Ÿ Protect this device from fall-down and intensive strikes, keep
the device away from magnetic field interference, and do not
install the device in places with shaking surfaces or under
shocks.
Ÿ Clean the device with a soft dry cloth. For stubborn dirt, dip the
cloth into slight neutral cleanser, gently wipe the dirt with the
cloth, and then dry the device.
Ÿ Do not jam the ventilation opening. Follow the installation
instructions provided in this document when installing the
device.
Ÿ Keep the device away from heat sources such as radiators,
electric heaters, or other heat equipment.
Ÿ Keep the device away from moist, dusty, extremely hot or cold
places, or places with strong electric radiation.
Ÿ If the device is installed outdoors, take insect- and moisture-
proof measures to avoid circuit board corrosion that can affect
monitoring.
Ÿ Remove the power plug if the device is idle for a long time.
Ÿ All complete products sold by the manufacturer are delivered
along with nameplates, quick setup guide and accessories after
strict inspection. The manufacturer shall not be held
responsible for counterfeit products.
Ÿ The manufacturer will update this manual according to product
function enhancement or changes and regularly update the
software and hardware described in this manual. Update
information will be added to new versions of this manual without
prior notice.
Ÿ This manual may contain misprints, technology information that
is not accurate enough, or product function and operation
description that is slightly inconsistent with the actual product,
the final interpretation of company is as a standard.
Ÿ This manual is only for reference and does not ensure that the
information is totally consistent with the actual product. For
consistency, see the actual product.
Precautions
Open the package, check the appearance of product for no
obvious damage, and confirm the item list for table 1-1 is
consistent.
Table 1-1 Packing list
2.1 Device Ports
Component
Quantity
Remark
Mini Dome Network Camera
Plastic anchor
Stainless self-tapping screw
Installation location sticker
Quick Setup Guide
1
2
2
1
1
NOTE
NOTE
this device. Otherwise, the service life of the image sensor may
be shortened.
Ÿ If this device is installed in places where thunder and lightning
frequently occur, ground the device nearby to discharge high
energy such as thunder strikes in order to prevent device
damage.
L hexagonal wrench
1
CAUTION
WARNING
WARNING
CAUTION
Open Package Examination
1
Device Structure
2
Figure 2-1 Device ports
Table 2-1 Interface of camera
NOTE
Different devices may have different device ports; Please refer
to the actual product.
Video Output
SD Card Slot
Reset Button
Network Access
Port
Over-line Buckle
Power
Supply
Audio in/out
Alarm in/out
Port name
Description
Remark
Video Output
Analog video output
SD card slot
Insert SD card
Reset button
Long press the reset button for 5
seconds to restore the original
settings.
4 PIN terminal
block
(applied for
alarm function)
OA
Alarm out A
Applied
for inner
line
dome
camera
OB
Alarm out B
IN
Alarm in
G
Ground
5 PIN terminal
block
(applied for
audio function
and power)
+
12V Po sit ive
-
12V Negative
Audio in
Receive an analog audio
signal from devices such
as a sound pickup
device.
Audio out
Connect to an external
audio device such as a
speaker.
G
Ground
Over-line
buckle
Fixed the internal line of device.
Network
access port
Connect to a standard Ethernet
cable.
Table 2-3 Multi-head cable 2 description
ID
Core
Description
Remark
1
Network
access port
Connect to a standard Ethernet cable or
PoE. The green light is on, the network
connection is normal; The yellow light
flashes when the data is transmitted.
Some models maybe not have the lights;
Please refer to actual product.
2
Audio output
port
Connect to an external audio device
such as a speaker.
3
Power supply
(DC 12V)
Connect to a 12V direct current (DC)
power supply
4
IN
Alarm input terminal
Applied
for
alarm
function
G
Alarm input COM
OUT
Alarm output terminal
G
Alarm output COM
Figure2-3 Multi-head cable 2
Network cable
✔
✘
Figure 2-2 Multi-head cable 1
1
2
Powe
r
NOTE
Different devices may have different device ports; Please
refer to the actual product.
Table 2-2 Multi-head cable description
ID
Core
Description
Remark
1
Network
access port
Connect to a standard Ethernet cable or
PoE. The green light is on, the network
connection is normal; The yellow light
flashes when the data is transmitted.
Some models maybe not have the lights,
please refer to the actual product.
Support
PoE
supply.
2
Power supply
(DC 12V)
Connect to a 12V direct current (DC)
power supply.
Por t
1
2
3
4
IN
OUT
G
G
ALARM
Reset
Por t
2
3
4
5
6
IN
O
UT
G
G
Connect to a standard Ethernet
cable or PoE. The green light is on,
the network connection is normal;
The yellow light flashes when the
data is transmitted. Some models
maybe not have the lights; Please
refer to the actual product.
Connect to an external audio
device such as a speaker.
Applied for
camera with
audio
function
Receive an analog audio signal
from devices such as a sound
pickup device.
2
1
ID
3
Network
access port
Support PoE
supply.
Core
Description
Remark
Audio output
Audio input
port
Figure2-4 Multi-head cable 3
Table 2-4 Multi-head cable 3 description