2 Volt 10 Amp SOLAR CHARGE CONTROLLER RÉGULATEUR DE CHARGE SOLAIRE,12 VOLTS, 10 AMPÈRES Item 60031 Item 60021 User’s Manual Notice D’utilisation
12 Volt 10 Amp Solar Charge Controller Maintain 12V batteries in a fully charged state IMPORTANT SAFETY AND OPERATION INSTRUCTIONS SAVE THESE INSTRUCTIONS The charge controller is designed to protect your 12 Volt Lead-acid battery from being overcharged as well as prevent discharge of the battery during nighttime. This controller reduces overall system maintenance and prolongs the battery life. The LCD Display will display the battery voltage (60031 only).
CONTROLLER DIMENSIONS 60031 Shown FEATURES • Digital Meter (60031 only) – Battery voltage is shown digitally. • Protect and Maintain battery – Protect batteries from overcharging and maintains batteries in fully charged state. • Safety circuit protection – Reverse polarity protection • Reverse leakage protection – Protect batteries from discharge by solar panel • Temperature Protection– Over temperature protection and auto-resume • Status Lights – Easy reading LED indicators.
CONNECTION DIAGRAM 60031 Shown Wire size: - Refer to the “WIRE SIZE” chart below to determine the minimum size wire needed for each connection. When using heavy stranded wire, you may need to divide the ends into two groups and straddle the screw on the terminal block. Any wiring variation of size or length can affect performance of the charge controller Length of Wire AWG Battery Connection Distance round trip (wiring provided) < 0.
SPECIFICATIONS Technical Specifications PARAMETERS UNITS ELECTRICAL: Normal input (solar cell array voltage) Volt Max. input solar cell array voltage Volt Peak charging current: Amps Current Consumption when connected 12V Array (Battery not present) Current Consumption when connected 12V battery (Array not present) CHARGING CHARACTERISTICS Max. Bulk charging current Constant voltage for Lead-acid battery Float mode voltage LCD METER DISPLAY: (60031 only) Min. LCD Display Voltage Max.
Solar power Weak Flashing OFF Indicates the solar panel voltage is too low (insufficient sunlight) Float Charge OFF ON Indicates full charge reached, a small “Float” charge continues to optimize battery when you need Digital LCD meter (60031 only) A digital LCD meter is available on this controller; it will continuously display battery voltage. MAINTENANCE 1. Ensure all wire connections are sound and free from corrosion. Tighten the terminal block screws of the array connections. 2.
Contrôleur de charge solaire, 12 volts, 10 ampères Il maintient les batteries de 12 volts toujours chargées. DIRECTIVES IMPORTANTES PORTANT SUR LA SÉCURITÉ ET LE FONCTIONNEMENT CONSERVEZ CE GUIDE. Le contrôleur de charge est conçu pour protéger votre batterie au plomb de 12 volts contre les surcharges et pour prévenir la décharge pendant la nuit. Ce contrôleur réduit l’entretien global du système et prolonge la durée de fonctionnement de la batterie.
L’INSTALLATION DEVRAIT ÊTRE EFFECTUÉE PAR UNE PERSONNE QUALIFIÉE. SUIVEZ AVEC SOIN LES INSTRUCTIONS PORTANT SUR LE CÂBLAGE.
– (PANNEAU SOLAIRE -) (indiquée par une étiquette « - ») du contrôleur de charge au moyen d’un fil approprié. • Branchez la borne positive de la batterie à la connexion positive BATTERY + (BATTERIE +) (indiquée par un collier rouge) du contrôleur de charge au moyen du fil à bride torique inclus ou d’un fil approprié (vous pouvez dénuder les fils à joints toriques sans pour cela annuler votre garantie).
FONCTIONNEMENT Lorsqu’il est monté et branché correctement, le contrôleur de charge commence à charger immédiatement pourvu que la lumière solaire soit adéquate. Le contrôleur de charge de 12 volts, 30 ampères, fonctionne selon un algorithme de charge à trois niveaux : le mode « Pleine charge », le mode « Tension constante » et le mode « Charge d’entretien ».
SURVEILLANCE Voyants DEL Les trois voyants DEL indiquent l’état de la charge. Ces fonctions sont décrites ci-dessous. Énergie solaire (DEL de l’alimentation - rouge) ALLUMÉ: Indique que les panneaux solaires sont branchés correctement et que l’alimentation solaire se rend normalement au contrôleur. ÉTEINT: Aucune alimentation présente ou tension insuffisante pour activer le contrôleur de charge.
batterie additionnelle. Dans cette condition, le contrôleur peut n’être branché qu’à une seule des batteries. • La batterie peut être défectueuse. Un bas niveau de charge ou de décharge affecte grandement la tension de la batterie. Les batteries doivent être éventuellement remplacées. • Les câbles peuvent être incorrectement branchés au contrôleur de charge. Assurez-vous que les câbles sont branchés en parallèle au contrôleur et aux bonnes bornes.