Owner’s Manual OUTDOOR PATIO HEATER MODEL# PHTRGH/SS-34 DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call you gas supplier or fire department. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
PACKAGE CONTENTS PART A B C D E F G H I J K DESCRIPTION Reflector Mesh Glass Tube Fixer Ceramic Fiber Top Plate Glass Tube Upper Support (Long) Protective Guard Side Panel Black Silicone Ring Control Box Assembly QUANTITY 1 1 1 1 1 1 3 3 2 1 1 PART L M N O P Q 2 A Reflector B Mesh C Glass Tube Fixer D Ceramic Fiber E Top Plate F Glass Tube G Upper Support (Long) H Protective Guard I Side Panel J Black Silicone Ring K Control Box Assembly L Lower Support (Short) M Block Belt N
HARDWARE CONTENTS (shown actual size) AA BB Wing nut Qty. 3 CC DD Stud Qty. 3 Small Flat Washer Qty. 6 Fixing Bracket Qty. 3 M5 x 12 mm Screw Qty. 31 HH GG FF KK Long Stem Lighter Qty.1 M6 x 12 mm Bolt Qty. 8 II M4 x 10 mm Screw Qty.1 Knob Qty. 1 JJ EE Chain Qty.1 LL Wrench Qty. 1 MM Phillips Screwdriver Qty. 1 AA Battery (1.5 V) Qty.1 SAFETY INFORMATION This manual contains important information about the assembly, operation and maintenance of this patio heater.
SAFETY INFORMATION DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
ASSEMBLY INSTRUCTIONS 1 1-1. Unscrew the switch button, load small battery, tighten the switch button. 1-2.Insert the hoods of bottom plate (P) to the lower holes of the three lower supports (L) Insert the hoods of control box assembly (K) to the upper holes of the three lower support (L). Note: Make sure align the side of bottom plate (P) with the holes with the side of control box assembly (K) with the magnet. MM AA Battery (1.5 V) K L P 2 2.
ASSEMBLY INSTRUCTIONS 3.Use Phillips screwdriver (LL) to fasten the control box assembly (K) and the bottom plate (P) with M5 x 12 mm screws (DD). 3 Hardware Used DD DD M5 x 12 mm Screw x9 LL Phillips Screwdriver x1 4 4. Use Phillips screwdriver (NN) to secure the top plate (E) to the upper supports (G) with M5 x 12 mm screws (DD).
ASSEMBLY INSTRUCTIONS 5. Using wrench (KK) to assemble the wheel assembly (O) to the bottom plate (P) with M6 x 12 mm bolts (EE). 5 P Hardware Used EE EE M6 x 12 mm Bolt x8 KK Wrench x1 O 6. Use Phillips screwdriver (LL) to secure the block belt (M) to the lower supports (L) with M5 x 12 mm screws (DD).
ASSEMBLY INSTRUCTIONS 7. Carefully install the glass tube (F) between the center of top plate (E) and control box assembly (K). Make sure the end of the glass tube (F) is inserted securely into the three clips of the control box assembly (K). 7 E F K 8. Assembly the glass tube fixer (C). Insert the ceramic fiber (D) to the quartz tube fixer. Press the glass tube fixer to the glass tube. Make sure the ceramic fiber is outside of glass tube.
ASSEMBLY INSTRUCTIONS 9. Use Phillips screwdriver (LL) to install side panels (I) to bottom of assembly with M5 x 12 mm screws (DD). Note: Do not cover the panel where the magnet is. 9 Hardware Used DD M5 x 12 mm Screw x8 LL Phillips Screwdriver x1 DD I 10. Install the knob (GG) to M4x10 screw (HH). Hang the chain (II) to the hole on the control box assembly (K) and put the pothook of front panel to the holes of bottom plate.
ASSEMBLY INSTRUCTIONS 11. Assembly the protective guard and mesh Insert the hooks of protective guard (H) to the holes of upper supports (G). Put the mesh (B) on the top plate (E). Make sure the screw holes align the holes of top plate (E).Use Phillips screwdriver (LL) to secure the mesh (B) and protective guard (H) to the top plate (E) with M5 x 12 mm screws (DD) and fixing bracket (FF). 11 B H FF DD Hardware Used DD M5 x 12 mm Screw x3 FF Fixing Bracket x3 LL Phillips Screwdriver x1 12.
ASSEMBLY INSTRUCTIONS 13. Connect regulator to cylinder. Install cylinder, and secure with the propane block belt tightly. Complete installation. Note: The propane gas and cylinder are sold separately. Warning: Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See chapter 12 of the standard for storage and handling of liquefied petroleum gas, ANS/NFPA 58 or CSA B149.1, Natural Gas and Propane Installation Code.
ASSEMBLY INSTRUCTIONS Warning: A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your propane supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER smoke while carrying out the leak test. • Do not use the heater until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak check solution (one part liquid dish washing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
OPERATION INSTRUCTIONS DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed. Before Turning Gas Supply ON: 1.
OPERATION INSTRUCTIONS 4. Push and release the igniter button until pilot flame is visible through the glass tube. 5. Once the pilot is lit, continue to depress the control knob for 30 seconds. 6. If the pilot does not stay lit, repeat steps 4 to 6. 7. If after repeating steps 4 to 6 unit does not light, then -Push in control knob and turn counterclockwise to “PILOT” (Figure 3). -As you are depressing the control knob, place long stem lighter through the glass tube to light the pilot (Figure 4).
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 20 seconds before igniting the gas will cause a ball of flame upon ignition. When heater is ON: The flame should be blue with straight yellow tops. If excessive yellow flame is detected, turn off heater and consult “Troubleshooting” on page 19.
OPERATION INSTRUCTIONS 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is located at least 24" (top) / 36" (sides) from combustible materials. 12. Heater is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Cylinder valve is closed Open valve Blockage in orifice or pilot tube Pilot won’t light Air in gas line Note: Heater operates Low gas pressure with cylinder valve fully open at reduced efficiency below 40ºF (5ºC) Igniter fails Pilot won’t stay lit Turn cylinder valve OFF and replace cylinder Use match to light pilot; obtain new igniter and replace Dirt built up around pilot Clean dirt from around pilot Connection between gas valve and pi
CARE AND MAINTENANCE Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard. Disassemble the reflector, unscrew the reflector spacer, take off the screen, and take down one side of protective guards. Then take the glass tube from the heater and wash and clear.
WARRANTY This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part will be repaired or replaced. Sunheat International’s obligation under the warranty is to replace or repair defective parts at our discretion.
REPLACEMENT PARTS LIST PART A B C D E F G H I J K DESCRIPTION Reflector Mesh Glass Tube Fixer Ceramic Fiber Top Plate Glass Tube Upper Support (Long) Protective Guard Side Panel Black Silicone Ring Control Box Assembly QUANTITY 1 1 1 1 1 1 3 3 2 1 1 22 PART L M N O P Q A Reflector B Mesh C Glass Tube Fixer D Ceramic Fiber E Top Plate F Glass Tube G Upper Support (Long) H Protective Guard I Side Panel J Black Silicone Ring K Control Box Assembly L Lower Support (Short) M Block B