Installation Guide

ManualsBrandsSunjoy ManualsOutdoor Bar FurnitureTulsa 3-Piece Patio Serving Bar Set

Fairbanks 3pc Bar Set-Bar

Item# L-DN1388SAL-A

Congratulations on your purchase of Fairbanks 3pc Bar Set-Bar. Our clear, easy to follow,

step-by-step instructions will guide you through the assembly process from start to finish.

WARNING:

 Keep all children and pets away from assembly area. Children and pets should be supervised

when they are in the area of the Bar construction.



Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,

overhanging branches, laundry line or electrical wires.

 Some parts may contain sharp edges. When assembling and using this product, basic safety

precautions should always be followed to reduce the risk of personal injury and damage to the

product. Please read all instructions before assembly and use.

 Check all bolts for tightness before use and periodically check and tighten bolts as necessary.

 Prepare a carpet or something else to protect the table top during assembling.

 Assemble on level ground.

 For outdoor use only.

IMPORTANT

Please take time to read these instructions thoroughly and follow each step carefully for safe and

easy operation. Keep this manual for future reference.

We would like to hear from you with any comments or suggestions. In the continental U.S., you

can call us toll-free at 1-888-301-0332 from 8 a.m. to 5 p.m. CST Monday – Friday. You can also

send us an email using the feedback icon at SamsClub.com.

Summary of content (8 pages)

PAGE 1
Fairbanks 3pc Bar Set-Bar Item# L-DN1388SAL-A Congratulations on your purchase of Fairbanks 3pc Bar Set-Bar. Our clear, easy to follow, step-by-step instructions will guide you through the assembly process from start to finish. WARNING:  Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the Bar construction.
PAGE 2
Parts List No. Description Qty A Bar Top 1 B Cup Holder 6 C1 Side Panel 1 1 C2 Side Panel 2 1 D Front Panel 1 E1 Shelf 1 1 E2 Shelf 2 1 F1 Wine Rack Frame1 1 F2 Wine Rack Frame 2 1 G Connect Bar 4 Hardware Pack No.
PAGE 3
Step1: Fig1: Attach Side Panel 1(C1) to Front Panel (D) by Inner Hexagon Bolt (AA) and Flat Washer (DD) as show in Fig 1. Then attach Side Panel 2 (C2) to Front Panel (D) in the same way. Fig2: Put Shelf 1 (E1) between Side Panel 1(C1) and Side Panel 2 (C2). Fix Front Panel (D) and Shelf 1 (E1) by Outer Hexagon Bolt (BB) and Flat Washer (DD) as shown in Fig 2. Then fix Shelf 2 (E2) in the same way.
PAGE 4
Step3: Fig 6: Turn over Bar Top (A) carefully and put it on a Carpet to protect the Table Top. Then fix Bar Top (A) with Side Panel (C1&2) by Outer Hexagon Bolt (II), Flat Washe (DD) and Nut (JJ) as shown in Fig 6. Step4: Fig7: Attach Cup Holder (B) and Bar Top (A) by Screw (FF) as shown in Fig 7. (Note: the side of Cup Holder (B) with bigger bend should be outwards.) Turn up the bar. Your Bar is now ready for use.
PAGE 5
Care & Maintenance Before using, clean the Bar completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. Limited Manufacturer’s Warranty: This product carries a 1 year warranty against defects in workmanship and materials.
PAGE 6
Fairbanks 3pc Bar Set-Chair Item# L-DN1388SAL-A Congratulations on your purchase of Fairbanks 3pc Bar Set-Chair. Our clear, easy to follow, step-by-step instructions will guide you through the assembly process from start to finish. WARNING:  Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the Chair construction.
PAGE 7
Parts List No. Description Qty A Seat Board 1 B Upper Connector 2 C Leg 2 D Down Connector 2 E Foot Mat (pre-assembled) 2 Hardware Pack No. Description Qty AA Bolt M6x20 8 BB Bolt M6x35 4 CC Bolt M6x15 4 DD Flat Washer M6 8 EE Hex Key M6 1 FF Spring Washer M6 8 Step 1: Set the side with connector of Leg (C) Step 2: Rotate the assembled leg 180°. Insert upwards.
PAGE 8
Step 3: Turn over Seat Board (A). Attach the assembled leg to Seat Board (A) by Bolt (BB), Spring Washer (FF) and Flat Washer (DD) as shown in Fig 5. Then lock all the bolts tightly by Hex Key (EE). Turn up the assembled chair. Your chair is now ready for use. Relax & Enjoy! Care & Maintenance Before using, clean the chair completely with a soft dry towel. When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse thoroughly and dry completely.