Installation Guide

ManualsBrandsSunjoy ManualsKitchenLarson 12 ft. x 10 ft. Aluminum Fabric Gazebo

Assembly Instructions

Item: L-GZ339PAL

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The

final product will be a quality piece that will go together smoothly and give years of enjoyment.

Tools Needed: Screwdriver & hammer & ladder (more than 2.5m/8.2feet).

Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which

the part is used.

Summary of content (7 pages)

PAGE 1
Assembly Instructions Item: L-GZ339PAL Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The final product will be a quality piece that will go together smoothly and give years of enjoyment. Tools Needed: Screwdriver & hammer & ladder (more than 2.5m/8.2feet). Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in which the part is used.
PAGE 2
Parts List Long Beam (1) A 2 Long Beam (2) B 2 Short Beam (1) C 2 Short Beam (2) D 2 Beam connector E 4 Corner Connector F 4 Reinforcement Slat G 4 Corner mandril connector (1) H 2 Corner mandril connector (2) I 2 Long slanting bar J 4 Short mid top bar K 2 Long mid top bar L 2 Big top connector M 1 Small top connector N 1 Pothook O 1 Small top pole P 4 Post Q 4 Base Q1 4 Support bar R 8 Large canopy S 1 Small canopy T 1 Mosquito netting U 1
PAGE 3
Hardware Pack 1 AA M6X15 bolt 64 PCS BB M6 flat washer 64 PCS DD Plastic Hook 144PCS STEP 1 Fig.0: Install Plastic hook (DD) to the Beam A (B, C, D) as Fig.0 shows. 8pcs hooks and 10pcs hooks needed on each short beam and long beam separately. Fig.1: Connect Long beam (A&B) with Beam connector (E) by using bolt (AA) and flat washer (BB). Connect short beam (C&D) with Beam connector (E) in the same way. Fig.
PAGE 4
STEP 2 Fig.5: Install the Pothook (O) onto the Big top connector (M); then insert the Long slanting bar (J), Short mid top bar (K) and Long mid top bar (L) into the Big top connector (M). (Here one person is needed to support the Top connector M). Fig.6: Insert the Long slanting bar (J) into the Corner mandril connector (H) & (I). Fig.7: Install the Short (Long) mid top bar K (L) on the connector of the top of the beam frame with bolt (EE) and flat washer (BB) and nut (FF). Fig.
PAGE 5
STEP 3 Fig.10: Connect Post (Q) and Base (Q1) with bolt (AA) and flat washer (BB). Fig.11: Four people will be needed to lift the whole top while another attaches the Post (Q) with the bolt (GG) and flat washer (BB). (Note: 5 people are needed.) Fig.12: Fix one end of support bar (R) on post (Q) and another end on the Long (Short) beam with bolt (HH) and flat washer (BB). Then spread the Large canopy (S) and tighten. Note: Tighten all of the bolts with Screwdriver and Wrench (W1). Fig.
PAGE 6
IMPORTANT: 1. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use. 2. Some parts may contain sharp edges, wear protective gloves if necessary. At least five or more people are recommended for safe assembly. 3. Keep all children and pets away from assembly area. 4.
PAGE 7
Limited Warranty: This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of your item provided the item is maintained with care and used only for personal, residential purposes. The item is warranted to be free from defects in material or workmanship for a period of one (1) year. We don't reimburse for transportation or delivery costs, or compensate the individual or any outside party for assembling or disassembling the product.