User's Manual

400 / 600 / 1000 Watt
+
Turbo Charge
®
***
READ THESE IMPORTANT INSTRUCTIONS BEFORE USING YOUR BALLAST
***
INSTRUCTION MANUAL
KEEP ORIGINAL PACKAGING— all
returns need to be in the original packaging in
order to avoid product damage during shipping.
Any damage to products not in their original
packaging will not be covered under warranty.
SAFETY FIRST! Failure to observe the
following safety warnings may result in
serious injury. In addition, failure to observe
these safety warnings will result in a waiver of
all liabilities and will void all warranties.
WARNING
 If the exterior of the lamp is damaged,
replace lamp immediately.
 When re-lamping, make sure lamp has time
to cool before touching.
 Make sure power cord and lamp cord are
connected properly.
Disconnect power before re-lamping.
 DO NOT make contact with the interior of
the socket while power is on.
 DO NOT operate light systems in wet locations.
 DO NOT attempt to rewire or reconfigure
your system, it will void warranty and could
cause serious safety hazards (i.e. power
cord, lamp cord, lamp socket or ballast).
DO NOT hang by power or lamp cord. 
  DO NOT plug system into supply voltage
other than what is designated on ballast.
Keep away from children.
 DO NOT alter or modify this unit in any
way. It may cause bodily injury or death as
this is a high power electrical device.
 DO NOT submerse in water or splash water
on the unit.
 DO NOT plug or unplug the lamp cord
while the ballast is energized.
These high performance Electronic Ballasts
are extremely efficient. They have a high
power factor and high luminous efficacy. It’s
stable performance creates constant power
output even when power fluctuates (power
surge). Short circuit protection technology
prevents damage to the lamp and other
ballasts connected to the same circuit.
1. INSTALLATION PROCEDURE
 DO NOT alter or modify the electronic
ballast in any way. Not only may it damage
the unit, it will void the warranty.
 Lamp power rating must match electronic
ballast power rating.
OUTPUT TO HPS/MH LAMP
Connect lamp cord with male plug
to dual universal female lamp cord
receptacle on ballast
WARRANTY This unit, when properly used will provide you with years of service. It is
covered under a 3 year warranty. This warranty will be voided if the unit is misused, abused
or altered. Warranty repair or replacement will be at the sole discretion of the manufacturer.
Defective units need to be returned to the place of purchase with proof of purchase/receipt.
This warranty is expressly in lieu of all other warranties, expressed or implied, including the
warranties of merchantability and fitness for use and of all other obligations or liabilities
on the part of the seller. This warranty shall not apply to this product or any part thereof
which has been damaged by accident, abuse, misuse, modification, negligence, alteration
or misapplication. Manufacturer makes no warranty whatsoever in respect to accessories
or parts not supplied by manufacturer. This warranty does not cover labor, materials,
equipment, etc. to install or de-install lighting fixtures or any other product. Buyers sole and
exclusive remedy shall be the repair or replacement of the defective product at the sellers
sole discretion. This warranty shall apply only to the United States, including Alaska, Hawaii
and territories of the United States and Canada.
RETURNING UNITS Please contact your retail store for returns.
CONNECT APPROPRIATE AC POWER
PLUG HERE AC input 120 (included)
or 240V (purchase separately)
The Galaxy Digital Logic offers our exclusive Smart Volt
®
feature, allowing operation on either
120 or 240 volt power by simply plugging in the appropriate power cord. There is no further
modification necessary. It comes with a 120 volt power cord. To run this ballast on 240 volt,
purchase the 240 volt power cord separately (part #903082 six foot or #903084 twenty foot).
2. SPECIFICATIONS
 120-240 Volts
 Power source frequency: 50/60Hz
 Power Factor (cosø): > 0.99
 Ambient Temp: 50˚F to 120˚F
Crest Factor: < 1.5
Acoustic Resonance: none
 Total Harmonic Distortion:
(THD): < 10.0%
www.galaxyballasts.com
Part 18 compliance This device complies with Part 18 of the FCC Rules.
Advisory statement
This product may cause interference to radio equipment and
should not be installed near maritime safety communications
equipment or other critical navigation or communication
equipment operating between 0.45-30 MHz.
The interference potential
of the device or system
The interference potential of the device or system is the
operating frequency; 60 kHz.
Maintenance of the system Unplug the unit, wait 30 seconds, and plug the unit back in.
Simple measures that can be taken
by the user to correct interference
Move the unit away from any radio device.
 This product contains delicate electronic components. This means that if it is
placed near an object that transmits radio signals, it could cause interference.
This could be, for example, mobile telephones, walkie talkies, CB radios, remote
controls and microwaves. If interference occurs, move such objects away from
the appliance.
 Do not use the fixture when either its lamp or its power cord are damaged.
Replace the power cord only with original certified cords. Replace the lamp only
with lamps specified by Gavita (see paragraph 10.1). Modifications to the cords
can lead to unwanted electromagnetic effects, which makes the product not
comply with legal requirements.
3. NOTES
Galaxy Electronic Ballasts will operate with Metal Halide lamps and High Pressure Sodium
lamps that are rated at the proper wattage. This unit offers short-circuit and power fluctuation.
MAINTENANCE
 Regularly check the ballast for dust or dirt buildup.
Clean the outside of the fixture using a dry or damp cloth.
 Regularly check the wiring of the product to ensure it is undamaged.