Installation Guide

WARNING - RISK OF ELECTRIC SHOCK.
DISCONNECT MAIN POWER AT FUSE OR CIRCUIT
BREAKER BEFORE INSTALLING OR SERVICING
THE FIXTURE.
LED 4” DOWN LIGHT INSTALLATION INSTRUCTIONS -
MODEL D634-N-XX-XXXX
Please read carefully and save these instructions, as
you may need them at a later date.
1. INSTALLATION OR ASSEMBLY INSTRUCTIONS
Wiring instructions that specify the proper method of connecting the
grounding means and maintaining polarity shall be included with the
luminaire in a manner that will require the installer to handle the instructions
during installation.
2. "THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED" and "CE PRODUIT DOIT ÊTRE INSTALLÉ SELON
LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI
CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE
LES RISQUES INHÉRENTS«
3. "CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT
BRANCH CIRCUIT CONDUCTOR" and "CONSULTER UN ÉLECTRICIEN
QUALIFIÉ POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA
DÉRIVATION SONT ADÉQUATS“
_________________________________________
WARNING- RISK OF FIRE OR ELECTRIC SHOCK
•DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF
WIRING OR ELECTRICAL COMPONENTS DURING LAMP
INSTALLATION.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE
WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.
•SUITABLE FOR WET LOCATIONS
•SUITABLE FOR TYPE IC OR SUITABLE FOR TYPE NON-IC
•THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS
_____________________________
ASSEMBLY AND INSTALLATION
This IC/AT fixture is intended for use in recessed cavities or suspened
ceilings(with or without insulation).Choose the location for the fixture,
taking into consideration the location of the joists, the 5-6 in.depth
clearancc and electrical supply.
• Shut off power before installation
• Cut 4 ½ in. hole in the ceiling. (FIG1)
• When running the supply wire(s),allow an additional 18 in.of wire
at each installation in order to make the electrical connections on
the room side of the ceiling hole,identify the size of the wire.(FIG2)
• Remove the Junction Box Screws holding the Junction Box Cover.
• Using a screwdriver,push through the ¾ inch hole on the side.
• Using the quick connectors in the junction box insert the wires in
the supply wire AS FOLLOWS:
WHITE WIRE IN SUPPLY WIRE TO WHITE WIRE IN QUICK
CONNECTOR (NEUTRAL)
BLACK WIRE IN SUPPLY WIRETO BLACK WIRE IN QUICK
CONNECTOR (HOT/LIVE)
GREEN / BARE WIRE IN SUPPLY WIRE TO GREEN WIRE QUICK
CONNECTOR (GROUND)
• Carefully stuff all wires/connectors back into the junction box.
• Snap/replace the cover on top of the junction box.(FIG3)
• Press the top portion of the spring clips against the side of the
Housing Assembly.(FIG4)
• Push the Housing Assembly with the top side of the Remodel Clips
through the hole until tight. Continue to push the Housing
Assembly until the fixture snaps into place with the trim tight
against the ceiling(FIG5)
DIMMING
Dimming performance may depend on the dimmer, the dimmer range adjustment setting (for dimmers with
brightness range adjustments), the wiring method, and/or the number of LED modules installed onto the
dimmer circuit.
•For dimmer selection, Dimming control manufacturers revise their product often; for the latest list of
compatible dimmers please visit our website.
•For best results, it is recommended to install a minimum of four LED modules onto one dimmer.
•Before turning on the LED lights, set dimmer position at maximum before adjusting to a lower light level.
•Please follow the dimming control manufacturer’s instructions for the installation of all dimming controls.