Instructions Notice

NFC reader
Used for sensing Quick Pass Card.
Magnetic card reader
Used for reading the information stored in the magnetic
stripe of bank card.
Front-facing camera (optional)
Supports photographing and 1D/2D code quick scanning.
Type-C USB
Used for charging equipment and debugging by developers.
Function Key
Used for customized function.
Power button
Short press: wake up the screen, lock the screen.
Long press: long press for 2-3 seconds in power off mode to
switch on the device.
Long press for 2-3 seconds in normal operation
mode to select power off or reboot.
Long press for 11 seconds when system is frozenfor
automatic reboot.
Printer
For printing sales slips in power on mode.
Indicator lamp
Used for indicating the steps for swiping card.
IC Card socket
Used for inserting the bank chip card.
Rear camera
Supports photographing and 1D/2D code quick scanning.
Extend pins
To connect to dock.(Need to buy dock separately)
Slide down the metal buckle and take out the Nano SIM
SIM card slot (PSAM optional)
Used for inserting the SIM Card(PSAM optional)
P-SAM card slot
Used for inserting the P-SAM Card.
Micro SD card slot
Used for inserting extend SD card.
Nano SIM card slot
Used for inserting Nano SIM card.
Quick start
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
This device supports 58mm thermal paper with the specifications
of 57±0.5mm*Ø40mm.
① Please open the paper container with the uncovering handl ，
Please do not force open the paper container to avoid print
head gear wear;
② Feed the paper correctly into the paper container in the
direction as shown, and pull some paper outside the cutter;
③ Close the cover of the paper container to finish printing paper
feeding .
Note: If the printed paper is blank, please check whether the
paper roll has been installed in the correct direction.
Printing instructions
Notices
Safety Warning
Connect the AC plug to the AC socket corresponding to the
marked input of the power adapter;
To avoid injury, unauthorized persons shall not open the power
adapter;
This is a Class A product. This product may cause radio
interference in living environments.
In that case, the user may be required to take adequate
measures against interference.
Battery replacement:
1.Explosion danger may arise if replacing with the wrong
battery!
2.The replaced battery shall be disposed of by maintenance
personnel, and please do not throw it into fire!
Significant Safety Instructions
Do not install or use the device during lightning storms to avoid
the potential risks of lightning shock;
Please turn off the power immediately if you notice abnormal
odor, heat or smoke;
The paper cutter is sharp, please do not touch!
Suggestions
· Do not use the terminal near water or moisture to prevent
liquid from falling into the terminal;
Do not use the terminal in extremely cold or hot environments,
such as near flames or lit cigarettes;
Do not drop, throw or bend the device;
Use the terminal in a clean and dust-free environment if possible
to prevent small items from falling into the terminal;
Please do not use the terminal near medical equipment without
permission.
Statements
The Company does not assume responsibilities for the following
actions:
Damages caused by use and maintenance without complying
with the conditions specified in this guide;
The Company will not assume any responsibilities for the
damages or problemscaused by optional items or consumables
(rather than the initial products or approvedproducts of the
Company). The customer is not entitled to change or modify the
product without our consent.
The product’s operating system supports official systemupdates,
but if you change the operating system into a third party ROM
system or alter the system files by system cracking, it may cause
system instability and security risks and threats.
Disclaimer
As a result of product upgrading, some details in this document
may not match the product, and the actual product shall
govern. The Company reserves the right of interpretation of this
document. The Company also reserves the right toalter this
specification without prior notice.
Table for Names and Content Identification of Toxic and
Hazardous Substances in this Product
Part Name
Toxic or Hazardous Substances and Elements
Pb Hg Cd
Cr(VII)
PBB PBDE
Circuit Board Component
Structural Component
Packaging Component
indicates that the content of the toxic and hazardous substance in all
homogeneous materials of the component is below the limit specified in
SJ/T 11363-2006.
indicates that the content of the toxic and hazardous substance in at least
one homogeneous material of the component exceeds the limit stipulated
in SJ/T 11363-2006. However, as for the reason, because there is no mature
and replaceable technology in the industry at present.
：
：
The products that have reached or exceeded environmental protection
service life should be recycled and reused according to the Regulations on
Control and Management of Electronic Information Products, and should not
be discarded randomly.
Manufacture
Shanghai Sunmi Technology Co., Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
Transmitted
32.5 dBm
29.5 dBm
23 dBm
23 dBm
23 dBm
22.5 dBm
22 dBm
23 dBm
23 dBm
23 dBm
23 dBm
13 dBm
5.5 dBm
4 dBm
19 dBm
Technical features and characteristic
Operation Frequency
824-849 MHz
1850-1910 MHz
1850-1910 MHz
1710-1755 MHz
824-849 MHz
1850-1910 MHz
1710-1755 MHz
824-849 MHz
2500-2570 MHz
704-716 MHz
2496-2690 MHz
2412-2462 MHz
2402-2480 MHz
2402-2480 MHz
5150MHz-5825MHz
13.56 MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: 2AH25T6900
NOTE: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply
With RF exposure requirements, a minimum separation distance of 5mm
must be maintained between the user’s body and the handset, including the
antenna.
Third-party belt-clips, holsters, and similar including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do
not meet these requirements may not comply with RF exposure.
This smart POS system meets the government's requirements for exposure to
radio waves.
The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons regardless of age or
health.
FCC RF Exposure Information and Statement. The SAR limit of USA (FCC) is
1.6W/kg averaged over one gram of tissue.
Device types: T6900 has also been tested against this SAR limit.
The highest SAR value reported under this standard during product
certification when properly worn on the body is 2.586W/kg（10gSAR， test
distance：0mm，limit 4W/kg）and 1.262W/kg (1gSAR， test distance：5mm
，limit 1.6W/kg). This device was tested for body-worn operations with the
back of the handset kept 0mm and 5mm from the body. To maintain
compliance with FCC RF exposure requirements, use accessories that
maintain a 0mm and 5mm separation distance between the user's body and
the back of the handset. The use of belt clips, holsters and similar accessories
should not contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not comply with FCC
RF exposure requirements, and
should be avoided.
GSM 850
GSM 1900
WCDMA BAND II
WCDMA BAND IV
WCDMA BAND V
LTE BAND 2
LTE BAND 4
LTE BAND 5
LTE BAND 7
LTE BAND 17
LTE BAND 41
WIFI
BT
BLE
5G WIFI
NFC