User Manual

ManualsBrandsSunnex ManualsLightingPF2006-32

Sunnex Inc. is ISO 9001-2000 certified

Installation Instructions

Sunnex PF Series Exam Lights

Models: PF2015-44, PF2017-44, PF28010, PF2006-32

1.1 Applications

The Sunnex PF Series light was designed specifically for medical applications. These versatile

halogen lights are ideal for hospital exam areas where high lighting intensity is needed.

1.2 Operation of light

The arm system is fitted with a friction hinge, a fixed arm and a flexible gooseneck arm. Tightening the knob

of the hinge when the fixed arm is in desired position, the gooseneck arm can then be set in desired

position. The lamp head can be adjusted in order to obtain the best light intensity. The light can be switched

on and off with the switch placed at the top of the lamp head.

NOTE! The switch only switches off the secondary voltage to the lamp. The plug-in transformer must be

pulled out from the wall socket in order to disconnect the lamp unit from the main voltage.

1.3 Cleaning and Disinfection

The lamp fixture can be cleaned as needed with a damp cloth and a mild detergent. For disinfection use a

soft cloth with a disinfectant solution such as isopropyl alcohol. NOTE! Do not introduce any fluids to the

inside of the lamp head as this could cause a fire hazard.

7”

(

178 MM

)

3”

(

76 MM

)

Summary of content (16 pages)

PAGE 1
Installation Instructions Sunnex PF Series Exam Lights Models: PF2015-44, PF2017-44, PF28010, PF2006-32 1.1 Applications The Sunnex PF Series light was designed specifically for medical applications. These versatile halogen lights are ideal for hospital exam areas where high lighting intensity is needed. 3” (76 MM) 7” (178 MM) 1.2 Operation of light The arm system is fitted with a friction hinge, a fixed arm and a flexible gooseneck arm.
PAGE 2
The glass lens can be cleaned with a damp cloth and a mild detergent and inside part of the lens can be easily cleaned with Q-tips. 1.4 Service The transformer, cold light reflector, and mounting parts can be replaced by the user, see 2.4. All other service can only be carried out by Sunnex. Only original parts must be used, if not the technical characteristics of the lamp might be changed. 2. Technical Data 2.1 The lamp is approved in accordance with IEC/EN 60601-1, IEC/EN 60601-2-41.
PAGE 3
lamp. If in doubt consult your technician or the supplier. Accessories other than here mentioned are not allowed to use as they may negatively affect emissions and immunity. The complete light must be recycled in accordance with WEEE standard. 2.5 Transportation and Storage This light is packaged in card board and should be transported protected from moisture. The light should be stored in a dry environment and room temperature.
PAGE 4
3. Bulb Replacement 1. 50W Halogen MR16 bulb, part#: 32146 2. Lens, part#: 32140 3. O-Ring, part#: 32135 4. Lens Cover, part#: 32141 5. Lens Cover screws T10 Torx head, part#: 32142 1. Unplug lamp from power source and wait at least one hour for lamp to cool. 2. Remove the three small screws (5) and remove the lens (2), o-ring (3) and lens cover (4). 3. Grip bulb (1) and firmly pull straight out from the bulb socket on the lamp back 4.
PAGE 5
G. Plug the transformer into power outlet and turn on lamp with switch on back of lamp head. d CAUTION! The arm is equipped with friction joints. Do not tighten the joints excessively as this will cause uneven movement and could damage the arm. 5 Sunnex Inc.
PAGE 6
5.2 PF Ceiling (PF2017-44) Ceiling Mount - 50W - Plug-in transformer A. Securely fasten lamp down tube from ceiling. It is recommended that 6-5/16" diameter or larger fasteners of the proper length for your individual application be used. Be sure down tube is securely mounted to structural framework. Down tube should be mounted plumb and square to ceiling surface. B. Be sure transformer plug is not plugged into power source at this time. C.
PAGE 7
PF CEILING BRACKET HOLE PATTERN (DIMENSIONS IN INCHES) 5.3 PF Mobile (PF2006-32) Mobile caster base - 50W A. Place the pole (2) in the center housing (4) B. Press down until you feel resistance. Assemble the clamp plate (5) using the provided screw (7) and washer (6). Do not tighten the screw. The teeth on the plate should face inwards. C. Insert each of the 5 legs into the center housing, and place the 2 lockable casters on opposite sides. D. Tighten the screw (7).
PAGE 8
Insert Arm Assembly into caster pole A. Loosen the set screw in the pole. Insert the stem of the light fixture arm into the pole and tighten the set screw until you feel resistance. B. Verify that the arm is securely locked in the pole. C. Turn on the light by pushing rocker switch on back of lamp 5.4 PF Direct Mount (PF28010) Direct Mount Articulated arm - 50W The PF28010 can be directly mounted to a plane surface. An optional C-clamp is also available.
PAGE 9
6. Symbols CE-Mark AC powered: This product must be sorted as Waste from Electrical and Electronic Equipment (WEEE): 7. Sunnex Limited Warranty 7.1 Limited Warranty. Sunnex warrants that the Product, if properly used, will be free from defects in material and workmanship, for a period of three (3) years from the date of shipment to Customer. This Limited Warranty extends only to the original buyer.
PAGE 10
POSSIBILITY OF SUCH DAMAGES. IN ANY EVENT, THE TOTAL LIABILITY OF SUNNEX TO YOU FOR ANY CAUSE WHATSOEVER SHALL BE LIMITED TO THE PURCHASE PRICE YOU PAID FOR THE PRODUCT. THIS LIMITATION SHALL APPLY REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT OR TORT (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE).
PAGE 11
The provisions of this Limited Warranty shall be governed by the laws of the Commonwealth of Massachusetts without regard to its conflict of laws principles. This Limited Warranty shall not be modified except by an agreement signed by both parties specifically referencing this Limited Warranty.
PAGE 12
Guidance and manufacturer’s declaration — electromagnetic emissions The PF LIGHT is intended for use in the electromagnetic environment specified below. The customer or the user of the PF LIGHT should assure that it is used in such an environment. Emissions test Compliance Emissions test CISPR 15 Complies Harmonic emissions IEC 61000-3-2 Not applicable Voltage fluctuations/ flicker emissions IEC 61000-3-3 .
PAGE 13
Guidance and manufacturer’s declaration — electromagnetic immunity The PF LIGHT Image Intensifier is intended for use In the electromagnetic environment specified below. The customer or the user of the PF LIGHT Image Intensifier should assure that it is used in such an environment.
PAGE 14
Guidance and manufacturer’s declaration — electromagnetic immunity The PF LIGHT is intended for use In the electromagnetic environment specified below. The customer or the user of the PF LIGHT should assure that it is used in such an environment.
PAGE 15
Recommended separation distances between portable and mobile RF communications equipment and the PF LIGHT The PF LIGHT is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
PAGE 16
REV. 2.2 FEB. 2009 16 Sunnex Inc.