7130 Lancer Rear Drive Magnetic Commercial Indoor Cycling Bike Owner’s Manual Made in Taiwan
INDEX IMPORTANT SAFETY INFORMATION ..................................................................... 1 EXPLODED DRAWING ............................................................................................. 2 PARTS LIST................................................................................................................ 3 ASSEMBLY INSTRUCTION.................................................................................... 4-9 USER INSTRUCTION ........................................
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions. 1.
Exploded Drawing
Parts list NO.
Assembly Instruction STEP 1: (Y) Attach the Front Stabilizer (18) and the Rear Stabilizer (14) to the Main Frame (Y) using 4 Bolts (10), 4 Washers (9) and 4 Nuts (8). Tighten and secure using spanner wrench.
Assembly Instruction STEP 2: (Y) Remove plug from head tube of Main Frame (Y). You may have to loosen handle to remove it. Insert the Handlebar Post (22) into the head tube of the Main Frame (Y). Move Handlebar Post (22) to the desired height. Tighten the Release Lever (6) to secure the Handlebar Post (22) into position. Slide the Handlebar (23) onto the Handlebar Post (22). Tighten the L Shape Adjustment Knob (17) to secure the Handlebar (23) into position.
Assembly Instruction STEP 3: Insert the Seat Post (43) into the seat tube located on the Main Frame (Y). Insert the Seat Slider (42) into the Seat Post (43). Tighten the Release Lever (6) to secure the Seat Slider (42) in place. Secure the Saddle (1) onto the post of the Seat Slider (42). Tighten the saddle clamp screw to secure the Saddle (1) in place. Use Release Lever (6) to adjust height of the saddle, use Release Lever (6) to adjust the saddle back and forth.
STEP 4: IMPORTANT: Read instructions carefully, failure to do so may cause permanent damage to your bike. Assembly Instruction 23 Connect Pedals L/R (11) onto the Left and Right Crank Arms (20 and 21). (Before you begin, immobilize the crank arms by turning the tension control adjuster all the way to the right). NOTE: Pedals L/R (11) are marked, L for the (left pedal) and R for the (right pedal). Left Pedal: align the left pedal, Pedal L (11) with the Left Crank Arm (20) at 90 degrees.
Assembly Instruction STEP 5: 24 Adjust the exercise resistance on the bike using the Tension Adjuster (24) to increase (-) or decrease (+) resistance. Emergency Brake – This bike can be instantaneously stopped by rotating the red Tension Adjuster (24) completely forward.
Assembly is complete!
Before beginning use of equipment, please be sure to inspect the entire bike carefully. Ensure that all moving and stationary parts have been properly installed and are operational. Inspect all screws, nuts and bolts as well to make sure that they are tightened and secure. 39 MOVING There are Moving Wheels (39) on the rear stabilizer. Hold the front stabilizer, and lift the bike until the wheels touch the ground. Then you can move the bike.
User Instruction This bike is designed to be used in fitness and health clubs. ASSEMBLY Properly assembling the equipment before use is very important. Be sure to follow all instructions as detailed in the assembly instructions section of the owner’s manual. ADJUSTING THE RESISTANCE Adjust the resistance of the bike using the Tension Adjuster. Increase the level of resistance by moving it forward, and decrease the level of resistance by moving it back.
Maintenance IMPORTANT: Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to ensure that the equipment is maintained regularly. Any components found to be worn and/or damaged should be replaced before continuing use of the equipment. Equipment should only be used and stored indoors, prolonged exposure to weathering and changes in temperature and humidity may have a severe impact on moving parts of the machine.
