BELT DRIVE MAGNETIC INDOOR CYCLING BIKE SF-B1709 USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions. 1.
EXPLODED DIAGRAM 1 3
EXPLODED DIAGRAM 2 HARDWARE PACKAGE #29 M5X12 2PCS #8 M10X25 4PCS #7 #86 S5 1PC D10XΦ20X2 4PCS #87 S6 1PC #94 S4 1PC #89 S13,15 1PC #88 S17,19 1PC 4
PARTS LIST No. Description Spec. Qty No. Description Spec.
Spring Washer D6 80 Spring 66 Washer D6XΦ12X1.2 5 81 Hex Screw M8 3 67 Wave Washer D12XΦ18X0.
ASSEMBLY INSTRUCTIONS STEP 1: Attach 2 Adjusting Pads (No. 5) and 2 Hex Nuts (No. 6) to the Rear Stabilizer (No. 3) by using Wrench (No. 88). Unscrew the 4 Hexagon Socket Head Screws (No. 8) with Allen Wrench (No. 87), remove the 4 Flat Washers (No. 7), 2 Shipping Tubes (No. 35) from the Main Frame (No. 1). Attach the Front & Rear Stabilizer (No. 2& No. 3) to the Main Frame (No. 1) using 4 Hexagon Socket Head Screws (No. 8), 4 Flat Washers (No. 7). Tighten and secure with the Allen Wrench (No. 87).
STEP 3: Insert the Seat Post (No. 18) into the Main Frame (No. 1). Set Seat Post (No. 18) at desired height. Insert Spring Knob (No. 13) and tighten to secure. Insert the Seat Horizontal Tube (No. 20) into the Seat Post (No. 18). Insert Spring Knob (No. 13) and tighten to secure. Attach the Seat (No. 21) to the Seat Horizontal Tube (No. 20) using the Wrench (No. 89). STEP 4: Thread Extension Wire 1 (No. 24) into Main Frame (No. 1). Insert Handlebar Post (No. 4) into Main Frame (No.
STEP 5: Remove Hexagon Socket Cap Screw (No. 38) from Handlebar Post (No. 4) using Allen Wrench (No. 86). Unscrew preassembled Bolt (No. 28) and Washer (No. 93) from Triangle Knob (No. 26). Place Handlebar (No. 22) on Handlebar Post (No. 4). Do not slide all the way on yet. Insert Bolt (No. 28) into the hole in the Handlebar (No. 22) from the bottom. Hold Bolt (No. 28) on the threaded end to keep it in place while you slide the Handlebar (No. 22) onto the Handlebar Post (No. 4).
ADJUSTMENTS GUIDE ADJUSTING THE BALANCE In order to achieve a smooth and comfortable ride, you must ensure that the stability of the bike is secured. If you notice that the bike is unbalanced during use, you should adjust the foot levelers located beneath the front and rear stabilizers. To do so, use the Wrench (No. 88) to loosen Hex Nut (No. 6) by turning it clockwise (direction A). With the screw loosened, rotate Adjusting Pad (No. 5) until it sits level with the surface that the bike is on.
DISMOUNTING THE BIKE WARNING! Do not dismount the bike or remove your feet from the pedals until the pedals have stopped completely. You can stop the flywheel at anytime by pushing down on Brake Handle (No. 16). ADJUSTING THE HANDLEBAR 26 Loosen the [handlebar adjustment] Spring Knob (No. 13) to raise or lower the handlebar to the desired position. Make sure the Spring Knob (No. 13) settles into the desired hole and secure it firmly by turning clockwise. Loosen Triangle Knob (No.
MAINTENANCE INSTRUCTIONS This is general information for daily, weekly and monthly maintenance to be performed on your bike. DAILY MAINTENANCE MONTHLY MAINTENANCE After each exercise session, wipe down all the equipment: seat, frame, handlebars. Pay special attention to the seat post, handlebar post and belt/chain guard. Sweat is very corrosive and may cause problems that require parts replacement later. 1.
EXERCISE METER FUNCTION BUTTONS MODE Press to select the function displayed or enter value after setting. Press and hold for 2 seconds to enter the RACE interface in STOP mode. SET To set up the target value of TARGET, TIME, DIST, CAL. Press the button and hold for 2 seconds to speed up the increment during stop mode. RESET Press the button to reset function value during setting mode. Press the button and hold for 2 seconds to reset all value except Odometer to zero.
4. 5. 6. 7. TIME will flash. Press SET to select a value. Press MODE to enter. Repeat to select values for DIST and CAL. RACE MODE Press and hold MODE for 2 seconds to enter RACE mode. 1. TARGET: the preset CADENCE. 2. In STOP mode, press SET key to enter the TARGET setting in stop mode Press SET to increase the CADENCE five at a time. The setting change is 15………110→115→120→15→ ↑←←←←←←←←←←←↓ 3. The setting range of 15 -120 (Preset value is 60 CADENCES. It equals six bars) 4. Each bar equals 10 CADENCE.
PULSE To measure the pulse, press MODE until meter is on the PULSE function. Hold the contact pads for at least 5 seconds to measure your pulse. This value is for reference only. It cannot be used as the basis for medical treatment. BATTERY: This monitor uses two AAA batteries. If the display appears incorrectly or becomes difficult to read, please install new batteries. Always change both batteries at the same time. Do not mix battery types and do not mix old and new batteries.