TOTAL BODY BIKE SF-B2710 USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1- 877 - 90SUNNY (877-907-8669).
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions. 1.
EXPLODED DRAWING 2
PARTS LIST No.
HARDWARE PACKAGE Ordering Replacement Parts (U.S. and Canadian Customers only) Please provide the following information in order for us to accurately identify the part(s) needed: ✓ The model number (found on cover of manual) ✓ The product name (found on cover of manual) ✓ The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front of the manual) Please contact us at support@sunnyhealthfitness.com or 1- 877 - 90SUNNY (877-907-8669).
ASSEMBLY INSTRUCTIONS STEP 1 Loosen and pull the Release Knob (No. 45) from the folded Rear and Front Main Frame (No. 54 and No. 55) and unfold. Attach Rear Stabilizer (No. 6) to the Front Main Frame (No. 55) using 2 Curved Washers (No. 2), 2 Spring Washers (No. 3), 2 Carriage Bolts (No. 1) and 2 Cap Nuts (No. 4). Secure and tighten with Spanner (No. A). Attach Front Stabilizer (No. 7) to Rear Main Frame (No. 54) with 2 Curved Washers (No. 2), 2 Spring Washers (No. 3), 2 Carriage Bolts (No.
STEP 3 Remove the pre-assembled 3 Nylon Nuts (No. 51) and 3 Flat Washers (No. 50) from the back of the Seat (No. 68) with Spanner (No. A). Attach the Seat (No. 68) to the Seat Tube (No. 67) with 3 Nylon Nuts (No. 51) and 3 Flat Washers (No. 50) that were removed. Secure and tighten with Spanner (No. A). Remove the pre-assembled 2 Carriage Bolts (No. 69), 2 Flat Washers (No. 50), 2 Cap Nuts (No. 4) and 2 Spring Washers (No. 3) from the Backrest Tube (No. 70) with Spanner (No. A).
STEP 4 Loosen and pull out Release Knob (No. 45), then insert Seat Tube (No. 67) into Rear Main Frame (No. 54). Insert and tighten Release Knob (No. 45) to secure. STEP 5 Attach Handlebar (No. 84) to the Front Main Frame (No. 55) with 4 Screws (No. 87), 2 Flat Washers (No. 75), 2 Curved Washers (No. 90), and 4 Spring Washers (No. 88). Secure and tighten with Allen Wrench (No. B).
STEP 6 Remove 4 Screws (No. 85) from the back of the Meter (No. 86) with Allen Wrench (No. B). Attach Meter (No. 86) to the Front Main Frame (No. 55) with 4 Screws (No. 85) that were removed. Insert Sensor Wire (No. 39) into the hole on the back of the Meter (No. 86). Make sure the wire does not get caught when you attach the meter. Insert Hand Pulse Wire (No. 83) into the hole on the back of the Meter (86). STEP 7 Connect Ankle Strap (No. 59) to the Exercise Bands (No. 79) above the Cover (No. 58).
ADJUSTMENTS & USAGE GUIDE ADJUSTING THE TENSION OF BIKE Adjust the tension of bike by rotating the Tension Knob (No. 80) clockwise to increase the level of resistance. Rotate the knob counter-clockwise to decrease the level of resistance. ADJUSTING THE TENSION OF EXERCISE BANDS Adjust the tension of Exercise Bands (No. 79) by pulling out Pin (No. 57) and moving Cover (No. 58) to desired setting. Insert Pin (No. 57) into one of the three holes.
ADJUSTMENTS & USAGE GUIDE FOLDING THE BIKE Loosen and pull the Release Knob (45), fold the bike, and then engage Release Knob (45) into one of the preset holes and tighten MOVING THE BIKE First fold the bike according to the instructions above. To move the bike, hold Handlebar (No. 84) and tilt the bike until the Movable Wheel located on the front stabilizer end cap touch the ground. With the wheels on the ground, you can transport the bike to the desired location with ease.
USING THE BIKE Using the Total Body Bike, you can do a variety of exercises as below.
METER INSTRUCTIONS AUTO ON/OFF: The meter will turn on when you press MODE key. After 4 minutes of inactivity, the meter will shut off automatically. FUNCTION BUTTONS MODE: Press for 2 seconds to turn on meter. SET: During STOP mode, press to increase the value of TIME, DISTANCE or CALORIES. RESET: During STOP mode, press to clear value or setting value to zero. FUNCTIONS 1.