FORCE FITMILL SF-T7723 USER MANUAL IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1- 877 - 90SUNNY (877-907-8669).
IMPORTANT SAFETY INFORMATION We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions. 1.
EXPLODED DIAGRAM 39 40 31 40 5 31 40 38 6 6 4 40 38 14 41 40 39 40 7 4 39 40 38 44 33 35 34 3222 30 42 28 31 28 30 22 28 3 22 29 22 13R 40 2 34 33 31 35 32 28 29 38 13L 16 25 25 25 16 23 37 36 8 28 30 3 24 31 15 22 29 30 29 28 26 27 17 22 24 22 11 21 43 25 21 17 21 21 1 10 19 19 28 29 30 27 26 12 20 20 9 12 18 2 18
HARDWARE PACKAGE #31 M8x45x20 4PCS #32 M8x15 4PCS #28 φ8.2xφ16.2x1.5 8PCS #29 M8 2PCS #38 M8x85x20 4PCS #40 φ8xφ20x1.5 10PCS #39 M8x50x20 4PCS #36 1PC #37 φ12xφ28x2.0 1PC #45 S6 1PC #46 S13-14 1PC #47 S17-S19 1PC #48 S5 1PC Ordering Replacement Parts (U.S.
PARTS LIST No. Description 1 Spec Qty No. Description Spec Qty Main Frame 1 25 Phillips Self Drilling Screw ST4.8x16 7 2 Bottom Frame 1 26 Transportation Wheel 3 Stabilizer Tube 2 27 Socket Pan Head Screw M8x40x15 2 4 Rear Handlebar 2 28 Flat Washer φ8.2xφ16.2x1.5 10 5 Front Handlebar 1 29 Nylon Nut M8 6 6 Middle Handlebar 2 30 Phillips Pan Head Self Drilling Screw ST5.
ASSEMBLY INSTRUCTIONS STEP 1: #31 M8x45x20 2PCS #32 M8x15 4PCS #28 φ8.2xφ16.2x1.5 8PCS #29 M8 2PCS Remove 2 Socket Pan Head Bolts (No. 31), 4 Socket Pan Head Screws (No. 32), 8 Flat Washers (No. 28) and 2 Nylon Nuts (No. 29) from Stabilizer Tubes (No. 3) with Allen Wrench (No. 48) and Wrench (No. 46). #46 S13-14 1PC #48 S5 1PC Attach Stabilizer Tubes (No. 3) to Bottom Frame (No. 2) with 2 Socket Pan Head Bolts (No. 31), 4 Socket Pan Head Screws (No. 32), 8 Flat Washers (No. 28) and 2 Nylon Nuts (No.
STEP 3: #36 1PC Attach Main Frame (No. 1) to Bottom Frame (No. 2) with 1 Round Knob (No. 36) and 1 Flat Washer (No. 37). Then tighten and secure with Round Knob (No. 36). #37 φ12xφ28x2.0 1PC 2 1 36 37 STEP 4: #38 M8x85x20 2PCS Insert Rear Handlebars (No. 4) to Front Handlebar (No. 5), then attach them to Bottom Frame (No. 2) with 2 Socket Pan Head Bolts (No. 31) and 2 Arc Washers (No. 40). #31 M8x45x20 2PCS #40 φ8xφ20x1.5 4PCS #48 S5 1PC Attach Rear Handlebars (No. 4) to Bottom Frame (No.
STEP 5: #38 M8x85x20 2PCS Remove 4 Socket Pan Head Bolts (No. 39), 4 Arc Washers (No. 40) from Middle Handlebars (No. 6) with Allen Wrench (No. 48). #39 M8x50x20 4PCS #40 φ8xφ20x1.5 6PCS Attach Middle Handlebars (No. 6) to Front Handlebar (No. 5) with 2 Socket Pan Head Bolts (No. 39) and 2 Arc Washers (No. 40). Do not tighten the Socket Pan Head Bolts (No. 39). #48 S5 1PC Attach Bottom Handlebar (No. 7) to Middle Handlebars (No. 6) with 2 Socket Pan Head Bolts (No. 39) and 2 Arc Washers (No. 40).
FOLDING INSTRUCTIONS Folding: To fold up the treadmill, loosen and pull out Round Knob (No. 36) and Flat Washer (No. 37). Lift up on the rear end of Main Frame (No. 1) until the Cylinder (No. 15) lock into the tube. [When the Cylinder (No. 15) successfully locks into the tube you will hear a clicking sound]. Then re-tighten Round Knob (No. 36) and Flat Washer (No. 37) to Bottom Frame (No. 2). Unfolding: To unfold the treadmill, loosen and pull out Round Knob (No. 36) and Flat Washer (No. 37).
HOW TO MOVE THE TREADMILL Before attempting to move the treadmill, please make sure that it has been properly folded. To tilt, start by placing one hand at Rear Handlebar (No. 4) to support the treadmill. Next, place one foot on position “A” to hold the bottom end of the treadmill steady. With your foot at “A”, slowly tilt Rear Handlebar (No. 4) downward towards the ground. Once Rear Handlebar (No. 4) reaches a low enough point, the transportation wheels will reach the ground and start rolling.
MAINTENANCE INSTRUCTIONS CENTERING THE WALKING BELT: If the walking belt is off centered, the unit will make noise. Please use the tool to re-adjust the walking belt if it is too loose or too tight. 1. When the walking belt moves to the right side, please turn the right side hexagon socket screw clockwise 1 or 2 circles, and then turn back a little bit. 2. When the walking belt moves to the left side, please turn the left side hexagon socket screw clockwise 1 or 2 circles, and then turn back a little bit.
TREADMILL LUBRICATION To reduce the friction of the walking belt and minimize wear, lubricant may be applied directly onto the treadboard and underside of the walking belt. Lift one side of the walking belt and touch the top surface of the treadboard. If the surface is wet, no lubrication is required. If the surface is dry, lift one side of the walking belt edge first and at the same time spray or apply lubricant to the board.