User manual

ManualsBrandsSUNPOWER ManualsPSU ComponentsAC/DC PSU module 5 Vdc 7 A 60 W

SUNPOWER TECHNOLOGY CORP.

16F-1, No.150, Jian Yi Rd., Chung Ho City, Taipei Hsien, Taiwan, R.O.C.

TEL: 886-2-8226-3100 FAX: 886-2-8226-3111

http://www.sunpower.com.tw

E-mail: sunpower@sunpower.com.tw

Specifications subject to change without notice.

2003/1/14

＊Safety Standard:

Approved: UL1950/ CSA C22.2 No 60950/ TUV EN 60950/ IEC 60950/

EMKO-TSE 207/94

＊EMI: FCC CFR47 Part 15 Class B/ EN50081-1/ CNS 13438 Class B

EMS: EN50082-1

＊Power factor correction P.F.>0.95

＊Universal full range AC/DC input

＊Over load, over voltage & short circuit protection

＊Built-in EMI filter, low ripple noise

＊100% 50℃ burn-in test.

＊2 years warranty

＊Operating temperature range: 0~70℃

＊De-rating factor 42℃~70℃:2%/℃

＊Storage temperature: -10 to +75℃

＊Humidity: Operation: 20% to 85% RH.(Non condensing)

Storage: 10% to 95% RH.(Non condensing)

＊MTBF: >290,000 hours

＊Universal full range 85~264VAC or 120~375VDC

＊AC Frequency: 47~63Hz

＊Current: <1.8A@100V

＊Inrush current: <30A@115V, <60A@230V

Cold start at 25℃ ambient

＊Leakage current: ≦1.5mA@AC 264V

＊Maximum power: 60watts

＊Setup time: 3Sec@115VAC, 1Sec@230VAC

＊Rise time: ≦20ms

＊ Hold up time: 16.7ms@115VAC, 80ms@230VAC

＊N.W.: 0.6Kg / 1pc; 30pcs / 1.18 Cu ft

/ 1 CTN

＊Connector: 7p/9.5mm pitch terminal block (Right angel type optional)

＊Terminal block with pc cover optional, show as below:

Type A: Stright pins with pc cover

Type B: Right angle pins with pc cover

ENCLOSURE

SPS-060PT Series

60W, Triple Output, P.F.C Fuction

159 x 95 x 38mm

6.26 x 3.74 x 1.50inch

MODEL NO. SPS-060PT1 SPS-060PT2 SPS-060PT3 SPS-060PT4

OUTPUT V1 V2 V3 V1 V2 V3 V1 V2 V3 V1 V2 V3

VOLTAGE +5 V +12 V -5 V +5 V +12 V -12 V +5 V +15 V -15 V +5V +12V +24V

MIN. LOAD 0.3 A 0.1 A 0 A 0.3 A 0.1 A 0 A 0.3 A 0.1 A 0 A 0.3 A 0.1 A 0 A

MAX. LOAD 8 A 3.5 A 1 A 7 A 3.5 A 1 A 7 A 3 A 1 A 6 A 1.5A 1.2A

Regulation

± 3% ± 5% ± 10% ± 3% ± 5% ± 10% ± 3% ± 5% ± 10% ± 3% ± 5% ± 10%

RIPPLE & NOISE(MAX.)

50 mV 120 mV 100 mV 50 mV 120 mV 150 mV 50 mV 150 mV 200 mV 50 mV 120 mV 200 mV

EFFICIENCY(TYP.) 74% 74% 74% 74%

FEATURES

AMBIENT

OUTPUT

INPUT

PACKING

Summary of content (8 pages)

PAGE 1
SUNPOWER TECHNOLOGY CORP. 16F-1, No.150, Jian Yi Rd., Chung Ho City, Taipei Hsien, Taiwan, R.O.C. TEL: 886-2-8226-3100 FAX: 886-2-8226-3111 http://www.sunpower.com.tw E-mail: sunpower@sunpower.com.tw ENCLOSURE SPS-060PT Series 60W, Triple Output, P.F.C Fuction CB 159 x 95 x 38mm 6.26 x 3.74 x 1.50inch FEATURES ＊Safety Standard: Approved: UL1950/ CSA C22.
PAGE 2
SUNPOWER TECHNOLOGY CORP. 16F-1, No.150, Jian Yi Rd., Chung Ho City, Taipei Hsien, Taiwan, R.O.C. TEL: 886-2-8226-3100 FAX: 886-2-8226-3111 http://www.sunpower.com.tw E-mail: sunpower@sunpower.com.tw Copy Right Sunpower Technology Corp. 2002, All Right Reserved. Specifications subject to change without notice.
PAGE 3
RS020400 SUNPOWER TECHNOLOGY CORP. SPECIFICATIONS OF SWITCHING POWER SUPPLY MODEL NO.: SPS-060PT1 REV.: 1.2 SPS-060PT2 SPS-060PT3 SPS-060PT4 (UL/cUL/TUV APPROVED) STAMP \QR0405 REV.:1.
PAGE 4
MODEL NO.: SPS-060PT SER. REV.:1.2 UL/cUL/TUV APPROVED RS020400 1. AC INPUT: 1-1.VOLTAGE: AC: 85V (MIN.) --- 264V (MAX.) DC: 120V (MIN.) --- 375V (MAX.) UNIVERSAL FULL RANGE. 1-2. FREQUENCY: 47--------63Hz. 1-3. CURRENT: 1.8A MAX. AT 100V AC INPUT, FULL LOAD CONDITION. 1-4. INRUSH CURRENT: 30A MAX. AT 115V AC INPUT, FULL LOAD CONDITION. 60A MAX. AT 230V AC INPUT, FULL LOAD CONDITION. * COLD START, AT 25℃AMBIENT. 1-5. LEAKAGE CURRENT: 1.5mA MAX. AT 264V AC INPUT.
PAGE 5
MODEL NO.: SPS-060PT SER. REV.:1.2 UL/cUL/TUV APPROVED RS020400 * TOTAL OUTPUT MAXIMUM 60 WATTS. ** THE OUTPUT VOLTAGE LOAD REGULATION IS LESS THAN THE VALUES IN THE ABOVE TABLE BY CHANGING EACH OUTPUT LOAD ±40% FROM 60% RATED OF LOAD, AND KEEP THE OTHER OUTPUTS AT 60% OF RATED LOAD. 3. ELECTRONIC CHARACTERISTICS: 3-1. RISE TIME: 20mS MAX. 3-2. HOLD UP TIME: 16.7mS MIN, TEST CONDITION AT 115V/60Hz AC INPUT, AC OFF POINT AT 0 DEGREE.
PAGE 6
MODEL NO.: SPS-060PT SER. REV.:1.2 UL/cUL/TUV APPROVED RS020400 7. EMC: THIS PRODUCT IS DESIGN TO COMPLY WITH THE FOLLOWING STANDARDS: 7-1. EMI (1). FCC CFR 47 PART 15 SUBPART J, CLASS B LIMIT (2). EN 50081-1:1997 EMISSION STANDARD EN 55022: 1997 CLASS B LIMIT EN 61000-3-2: 1995 CLASS A EN 61000-3-3: 1995 (3). CNS 13438 CLASS B. 7-2. EMS (1). EN 50082-1 (1997) IMMUNITY STANDARD: EN 61000-4-2: 1995 ELECTROSTATIC DISCHARGE STANDARD. EN 61000-4-3: 1996 RADIATED RF STANDARD.
PAGE 7
SPS-060 (3.3V, 5V) / SPS-060P (3.3V, 5V) SPS-070 / SPS-070P / SPS-075 SDS-060 Series User’s Menu To Serialize Switching Power Supplies: a. To up rise output voltage: INPUT Power Supply (1) 12V Please read this user's guide carefully before setup. LOAD INPUT Power Supply (2) 12V Input: 1. Input range: SPS-060 (3.3V, 5V) / SPS-060P (3.3V, 5V) / SPS-070 / SPS-070P: b. To generate both positive and negative output voltage.
PAGE 8
A. Directly mount to system chassis: C. Mounting holes dimension: System chassis 2- M3x(4+t) t = thickness of chassis Safety terms: 1. The Y capacitor inside power supply could deliver leakage current. When multiple power supplies work in parallel or in series, the leakage current will increase to cause the possibility of getting electric shock. Make sure ground wire is thick enough to prevent the danger. 2.