Blower Assembly

ManualsBrandsSunStar ManualsAppliancesSC30T-1-LP Thermostat Control Vent-Free Room Heater

Form #43127360

-1- July 09

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

OPTIONAL THERMOSTATIC BLOWER ASSEMBLY

No. SC30T

INSTALLATION INSTRUCTIONS

(for Heater Models SC30T-1, SC30M-1)

GENERAL INFORMATION

This series is design certified by the CSA Laboratories as an Unvented Heater, and must

be installed according to these instructions.

ANY ALTERATION TO THE ORIGINAL DESIGN, INSTALLED OTHER THAN AS

SHOWN IN THESE INSTRUCTIONS, OR USED WITH A TYPE OF GAS NOT SHOWN

ON THE RATING PLATE IS PROHIBITED AND VOIDS THE WARRANTY.

The installation must conform to local codes. In the absence of local codes, the installation

must conform to the National Fuel Gas Code, also known as NFPA 54 and ANSI Z223.1-

latest edition.

This is a heating appliance. Any safety screen or guard removed for servicing the

appliance must be replaced prior to operating the appliance.

These instructions cover the installation of an accessory blower into a new heater prior to

installation. If the Heater is already installed then the following instructions shall be referred

to for the removal and re-installation of the heater.

Form Number Heater Model

#43126220 SUNSTAR SC30T-1

#43126210 SUNSTAR SC30M-1

Before continuing to remove the heater, seek a qualified service person to disconnect the

gas.

READ ALL THE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THE BLOWER.

Summary of content (8 pages)

PAGE 1
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. OPTIONAL THERMOSTATIC BLOWER ASSEMBLY No. SC30T INSTALLATION INSTRUCTIONS (for Heater Models SC30T-1, SC30M-1) GENERAL INFORMATION This series is design certified by the CSA Laboratories as an Unvented Heater, and must be installed according to these instructions.
PAGE 2
INSTALLING OPTIONAL BLOWER 1. Check contents of the carton before proceeding with the installation. Wiring Diagram 6 Fan Control Bracket 1 2 Nameplate 7 8 3 4 5 10 9 11 Fan Control Switch KIT NO. 43741570 – for Heaters SC30T-1, SC30M-1 ITEM NO. 1) 2) 3) 4) 5) 6) PART NO.
PAGE 3
. Attach fan Control Bracket and feed wires through the hole. Terminals Fan control bracket Sheet metal screws 4. Turn the heater over, assemble the cord retainer and insert through the back of the heater.
PAGE 4
5. Turn the heater over again, insert the plastic bushing into the “L” Bracket and attach it to the heater. Plastic bushing Sheet metal screws L Bracket 6. Lay down the blower beside the heater and pass the 3 wires through the plastic bushing. Secure fan control switch wires using wire clamp and screw.
PAGE 5
7. Make electrical connections shown in the diagram below. WIRING SCHEMATIC DIAGRAM OPTIONAL BLOWER Fan Control Switch White Blower Motor Violet Violet 120V Black If any original wire, as supplied with this appliance, has to be replaced, it must be replaced with #18 gauge, 125ºC, 2/64 insulation or its equivalent. Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
PAGE 6
8. Carefully insert the blower assembly under the lip of the heat shield and rotate into place. Blower assembly Blower case Heat shield 9. Lower the blower into the heater and secure both ends with sheet metal screws.
PAGE 7
STEP 1. STEP 2. STEP 3. STEP 4. LO HI Fan thermostat off after 5 mins, Blower OFF Legend: Function ON: LO HI Step 1 T0 T1 T2 T3 -7- TO TURN OFF GAS TO APPLIANCE Turn the thermostat (gas control knob) clockwise to the OFF position. Do not use excessive force when turning knob. Turn off all electric power to the appliance. 6. Repeatedly push the piezo ignitor button until the pilot is lit (a match can also be used to light pilot buner).
PAGE 8
CLEANING The blower wheel will collect lint and could require cleaning once a year. If the air output decreases, or the noise level increases, it indicates a dirty wheel. Clean the blower wheel with a vacuum cleaner or apply high-pressure air to the blower wheel. NOTE ! Unplugging of blower accessory will not stop the heater from cycling. To shut the heater off, turn the control knob to "OFF".