Spec Sheet

ManualsBrandsSunstone ManualsOutdoor CookingDesigner Series 304 Stainless Steel 34 in. x 34.5 in. x 28.25 in. Appliance Cabinet for up to 25 in. W Fridge

COVER &

1-GANG BOX

FRONT & BACK

KICK PLATES

Product Dimensions

Product Inserts

SUNSTONE METAL PRODUCTS

DESCRIPTION

34" Appliance Cabinet for up to 25" Fridges

& Ice Makers w/Convenient front Electrical

Cover & Interior Back Panel 1-Gang

Electrical Box

34" Appliance For up to

25" Wide Fridge

Item No. SAC34APC

PRODUCT

16004 CENTRAL COMMERCE DR.

PFLUGERVILLE, TEXAS 78660

Tel: 888.934.9449

Bus: 512.487.5116

Fax: 512.487.7016

34"W x 28-1/4"D (w/Panel)

x 34-1/2"H (w/Legs) or 30-

1/2"H (no Legs) or Upto 36"

Max Adjustable Height

34-1/2" HEIGHT W/LEGS

30-1/2" HEIGHT W/O LEGS

MATERIAL SPECS

304 Stainless Steel entire

structure, 18 Gauge for Door

Panel , 18 Gauge for Cabinet

Box, 18 Gauge for Shelf,

Handles are made of Solid 304

Stainless Steel Bar.

Configuration Options

1-GANG

ELECTRICAL BOX

INCLUDED COMPONENTS

�Front Kick Plates

�Back Solid Kick Plate

�(4) Adjustable Peg Legs

�Front Electrical Cover

�Back Panel Electrical Box

28-1/4" Depth

w/Panel

34" Width

PRODUCT DIMENSIONS

INSERT DIMENSIONS

25" Width x 33-1/4" Height x

25-1/4" Depth

INSERTABLE PRODUCTS

Works with up to 25" Wide

x 35-1/2" Height Fridges,

Wine Coolers & Ice Makers

4" SS PEG-LEGS

REMOVABLE

COUNTER RAIL

25" WIDTH

18-3/4" DEPTH

33-1/4"

HEIGHT

INCREASE

PEG-LEG

EXTENSION

RAISES 1-1/2"

ADDITIONAL

FOR ADA LEG

THE HEIGHT

IS 31-1/4"

25" WIDTH

SEE PAGE 3 OF SETUP-GUIDE

HOW TO INCREASE WIDTH

25-1/4" DEPTH

FRONT PANEL

TO LOWER

BACK SUPPORT

1. Standard Appliance

insert is 25" Width by

34" Height - leave min.

1/2" clearance all sides.

2. Remove top Counter

Rail & Support to give

additional 1" Height for

taller appliance. Adjust

Peg-Leg Upto 1-1/2"

for increased height

allowance.

ADD 1" HEIGHT

BY REMOVING

COUNTER RAIL

& SUPPORT

�Lifetime Structure Warranty

�304 Stainless Steel Structure

�Front & Back Kick-Plates

�Easy Pin-Lock Installation

�Covered Access Ports

�Adjustable Peg-Legs

�Optional Wheel Casters

�Assembly Required

Summary of content (5 pages)

PAGE 1
Product Dimensions Product Inserts 28-1/4" Depth w/Panel 34" Width 18-3/4" DEPTH 25" WIDTH ADD 1" HEIGHT BY REMOVING COUNTER RAIL & SUPPORT HT W/LEGS 34-1/2" HEIG 1-GANG ELECTRICAL BOX COVER & 1-GANG BOX 30-1/2" H EIGHT W/O LEGS REMOVABLE COUNTER RAIL SUNSTONE METAL PRODUCTS 16004 CENTRAL COMMERCE DR. PFLUGERVILLE, TEXAS 78660 Tel: 888.934.9449 Bus: 512.487.5116 Fax: 512.487.
PAGE 2
SAC34APC SETUP INSTRUCTIONS A Before proceeding, review the individual Specification Sheets of each Panel, follow any base setup instructions - do not install any kickplates. SCC25SPE SCC4SPEL 1 SCC4SPER Bring all three panels together Item Numbers SCC25SPE, SCC4SPEL & SCC4SPER while supporting each in hand upright, elevate the back panel SCC25SPE so the individual Pins align up to the adjacent notches and the back panel attaches to each side item SCC4SPEL on left and SCC4SPER on right.
PAGE 3
SAC34APC SETUP INSTRUCTIONS C SCC25SPE 2 IMPORTANT! If you are placing any appliance which product height is higher than 34-1/2", you can either increase the height of Peg-Leg up to an additional 1-1/2" higher, or simply do not install the Support Arm giving you an immediate 1" additional height clearance. Packaged with the back panel item no. SCC25SPE there is a cross-beam support with counter rail attached. This support beam supports the counter front.
PAGE 4
SAC34APC SETUP INSTRUCTIONS E 3 CREATE MULTIPLE APPLIANCE RUN BY ADDING ADDITIONAL BACK PANELS. 1 2 Connect multiple back panels to create multifridge Runs use Item No. SCC25SPE for Fridges up to 25" Width, SCC21SPE for Fridges up to 21" Width, and SCC15SPE for Fridges up to 15" Width. When connecting panels together you must use bolts in conjunction with the Lock-Nuts.
PAGE 5
SAC34APC SETUP INSTRUCTIONS G 4 IMPORTANT! Install All Electrical Boxes, & Peg Legs before proceeding further, follow these instructions. Electrical Wires are installed after all cabinets are connected but before counter is installed. Always use GFCI 2 way Electrical Outlet in front facing panel, standard electrical can be placed on the interior. See cover panel can be removed and hung below when electrical is in use.