TT-SK15 USER MANUAL SOUND BAR
Contents Features .....................................................................................................................2 Contents For your Attention........................................................................................................3 Panel.......................................................................................................................4-5 Connections......................................................................................................
Features Thanks for your purchase of our product. Please read through this manual before making connections and operating this product. Retain this manual for future reference.
For Your Attention IMPORTANT NOTES Please read through this manual before making connections and operating this product. Retain this manual for future reference. Don't open the cabinet of this unit. No user-serviceable parts inside. Refer servicing to qualified personnel only. Switch off the unit when you don't use it. Switch off the unit and disconnect it from the AC power supply when it is not being used for a long time. Don't install the unit in a place exposed to heating sources or direct sunshine.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Panel FRONT PANEL: Standby/ON BT LINE/AUX COAX/OPT 1 2 3 4 5 6 7 8 1 STANDBY Press to switch on the sound base; Press it again to put the sound base in standby mode. (STANDBY--red indicator, BLUETOOTH--red and blue indicator is ready for pairing enabled device, blue indicator flahing means has connected to the sound base.
Panel REAR PANEL: 1 2 4 3 1 LINE INPUT 2 OPTICAL INPUT 3 COAXIAL DIGITAL AUDIO INPUT 4 AC INPUT SIDE PANEL: 1 AUX INPUT 1 2 -6-
Connections AUX IN/LINE IN AUDIO INPUT This sound base has an extra group of audio input terminals. You can input the analogue stereo audio signals from extra devices such as VCD, CD, VCR, DVD player, etc. Use the audio cable to connect the stereo audio output terminals of a VCD, CD, VCR,DVD player to the stereo input terminals AUX IN/LINE IN of this sound base. Its corresponding signal source is AUX IN/LINE IN which can be available by pressing [AUX]/[LINE] on the remote control.
Connections BLUETOOTH Press standby button to power on the sound base, then press source button to switch the corresponding bluetooth mode, the blue indicator flashing , the sound base is in searching bluetooth signal status, use your smart phone to search the bluetooth signal of the sound base, select HSB3818 on your list, input the password 0000 if need the password prompt, the sound base will synchronize to play songs on your mobile phone while they connected successfully.
Remote control Remote Control Operation Insert the batteries into the remote control. Point the remote control at the remote sensor on the front panel. The remote control works within a distance of about 8 metres from the sensor and within an angle of about 30 degrees from the left and right side. Battery Installation Remove the battery compartment cover on the back of the remote control. Load one AAA/1.
Remote Control 1 2 9 3 4 10 5 6 7 8 11 1 STANDBY 2 BT 3 VOLUME+ 4 PREVIOUS 5 PLAY/PAUSE 6 VOLUME7 COAXIAL 8 MUTE 9 LINE/AUX 10 NEXT 11 OPTICAL -10-
Basic Playback Operation STANDBY Press to switch on the unit. Press it again to put the unit in standby mode. Press to enter to bluetooth.. Press to enter to COAXIAL IN mode. Press to enter to OPTICAL IN mode. LINE/AUX Press repeatedly to switch between LINE and AUX IN mode. Press to temporarily pause a playback. Press it again to resume the playback. Hold down this button for 3 seconds to disconnect bluetooth. Press to skip to the next chapter/track. Press to return to the previous chapter/track.
Troubleshooting Before resorting to maintenance service, please kindly check by yourself with the following chart. Symptom No Power Sound There is no sound or the sound is distorted. Cause(s) Remedy The DC power cord is not connected to the power Please check that the DC power cord is connected securely. supply or is not connected to a power supply securely. The audio cables aren't connected securely. The volume is set to the minimum level. The sound is switched off. Connect the audio cables securely.
Specifications Power supply Temperature Working environment Relative humidity Power output (Max) Frequency response AC ~100-240V,50/60Hz 20W -10~+35 5%~90% 20WX2 3dB(20Hz~20kHz) -13-
