Owner's Manual

ManualsBrandsSunwell Technology ManualsElectronicsFireplace Remote Control

Page 1 of 5

Model: RCB04A

Standard Thermostatic On/Off Remote Control

INSTALLATION AND OPERATING INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS

DO NOT ATTEMPT TO INSTALL OR OPERATE

INSTRUCTION:

This wireless thermostatic on/off/ remote control system provides a safe, reliable, and user-

friendly remote control for millivolt valve gas appliances. The system can be thermostatically or

manually turned on and off with the transmitter. Always check the appliance home owner’s

manual for additional information, or warnings regarding accessory installation before

connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged,

immediately contact the dealer from whom you purchased the kit. Do not attempt to install any

part of the kit unless all parts are in good condition. Please keep these instructions for future

reference.

CONTENTS OF KIT

Description

Quantity

RCB04A Thermostat remote control Transmitter

Installation Instructions

Screws (for install Transmitterl)

Screws Cap (for install Transmitterl)

Wall Clip (for install Transmitter)

NOTE:Due to the sensitive temperature monitoring components in the transmitter,it is necessary

to allow the transmitter to stabilize to room temperature before accurate room temperature are

displayed, If the transmitter is activated from a severe cold condition allow 15 minutes for

accurate temperature reading to appear on the LCD.

WARNING

Important Safety Information

 Read this manual thoroughly prior to installing, programming or operating any remote

control.

 This remote control system is designed for use with a millivolt or 24V gas valve system.

Do not use this remote control system on applications with voltages above 24 Volts

AC/DC and 1 amp current.

 This remote control Transmitter requires two (2) “AAA” alkaline batteries to power the

transmitter

FEATURES/SPECIFICATIONS

 Easy Access Thermostatic Control

 Low Battery Indication

 Child Proof Lock-out

 Select Between °C and °F display.

 4 bits DIP Switches Select Security Codes

Summary of content (5 pages)

PAGE 1
Model: RCB04A Standard Thermostatic On/Off Remote Control INSTALLATION AND OPERATING INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INSTRUCTION: This wireless thermostatic on/off/ remote control system provides a safe, reliable, and userfriendly remote control for millivolt valve gas appliances. The system can be thermostatically or manually turned on and off with the transmitter.
PAGE 2
Transmitter: Installing Batteries: The remote transmitter uses two (2) “AAA” batteries. To install batteries: 1. Press down the battery door and remove the battery door. 2. Install uses two (2) “AAA” batteries batteries as indicated on transmitter. 3. Close the battery door by snapping in place. 4. The batteries should be replaced when the low battery indicator display in LCD. 5. When both batteries are installed, the transmitter will initialize for 1 seconds and then is ready for use.
PAGE 3
OPERATIONS: Transmitter: General: The RCB04A Remote Control has two (2) operating modes: Manual and Thermostatic. The control system can be set to temperature ranges between 45°F and 99°F. The transmitter will operate the remote receiver from 1 foot to 30 feet. The distance is reduced when batteries are low or when the receiver is inside a metal enclosure. Initial start up: 1. After initial power up the transmitter is reset. 2. During system reset, all features of the LCD will be visible.
PAGE 4
2. The remote control will not work until child-proof mode is deactivated by pressing the ”ON”and”MODE” buttons at same time for 5 seconds again to exit child-proof mode. TRANSMITTER WALL CLIP The transmitter can be hung on a wall using the clip provided. If the clip is installed on a solid wood wall, drill 1/8” pilot holes and install with the screws provided. If it is installed on a plaster/wallboard wall, first drill two 1/4” holes into the wall.
PAGE 5
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.